Orderman Vapiano User manual
User Manual
Touch Terminal
ORDERMAN
-Touch Terminal
- 2 -
© 2005 by
Bachstraße 59,
5023 Salzburg – Österreich
www.orderman.com
Errors and misprints excepted.
Copyright, all rights reserved.
Duplication, reproduction or distribution, even in part, is prohibited without the written consent
of think dig high tech solutions gmbh.
P3.65-088 V1.0
• think dig assumes no responsibility for injuries or losses resulting from the utilization of these
instructions.
• think dig assumes no responsibility for losses or claims by third parties resulting from the use
of the charging station.
• The contents of these instructions are subject to changes, which can be carried out without
prior notice.
• These operating instructions do not constitute part of a contract.
• Any changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.
Windows, Windows CE and ActiveSync are registered trademarks from Microsoft Corporation.
Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respec-
tive companies and are used only for identification or explanation and to the owners’ benefit, without intent to infringes.
ORDERMAN
-Touch Terminal Manuale d’uso
- 3 -
Italiano
1Introduction of the ORDERMAN-Touch Terminal......................................................... 4
2The MenuCard............................................................................................................... 5
2.1 The ORDERMANToolbar .................................................................................... 5
3The Operating system of the ORDERMAN-Touch Terminal......................................... 6
3.1 The Windows CE licence ....................................................................................... 6
3.2 The Desktop .......................................................................................................... 6
3.3 The Start menu ...................................................................................................... 7
3.3.1 Run .................................................................................................................................... 7
3.3.2 Help.................................................................................................................................... 7
3.3.3 Settings .............................................................................................................................. 7
3.3.4 Programs ........................................................................................................................... 7
3.4 The Taskbar Icons ................................................................................................. 7
3.5 The Input Panel...................................................................................................... 8
3.6 MyComputer .......................................................................................................... 8
3.7 The Control Panel.................................................................................................. 8
4Saving files and settings (registry) ................................................................................. 8
5HowTo...........................................................................................................................9
5.1 Connect the OM-TT to a Local Area Network......................................................... 9
5.2 Active Sync ...........................................................................................................10
5.3 Use the Registry Editor .........................................................................................11
5.4 Install a Compact Flash Card................................................................................11
5.5 Install a program ...................................................................................................11
5.6 Remove a program ...............................................................................................11
5.7 Save system settings / changes in the registry......................................................12
5.8 Change the MenuCard..........................................................................................12
5.9 Change the Keyboard layout.................................................................................12
5.10 Re-calibrate the touch...........................................................................................13
5.10.1 Calibrate by using the Control Panel........................................................................... 13
5.10.2 Shortcut to the touch calibration.................................................................................. 13
5.11 Starting Programs at Start Up ...............................................................................14
5.12 Add a Link to the Desktop .....................................................................................14
5.13 Change the background image of the Desktop .....................................................14
5.14 Hide the Taskbar...................................................................................................14
5.15 Use Remote Desktop / RDP..................................................................................14
5.15.1 Automatic start of the Remote Desktop Connection ................................................... 15
5.16 Restart the ORDERMANTouch Terminal ...........................................................16
5.17 Set the ORDERMANTouch Terminal back to factory defaults ............................16
6Programs on the ORDERMANTouch Terminal ..........................................................16
6.1 OM-TT Process Viewer.........................................................................................16
6.2 SDAuthUtilDevice .................................................................................................17
6.3 RegClear...............................................................................................................17
6.4 RegFlush ..............................................................................................................17
6.5 RegEditSave.........................................................................................................17
6.6 Installation Backup / FileSystemWatcher ..............................................................17
6.7 TextEditor .............................................................................................................17
6.8 OMTTHWManager................................................................................................17
7Special Files/Folders on the ORDERMANTouch Terminal.........................................18
8FAQ’s ...........................................................................................................................19
8.1 What’s the Installation Backup good for ? .............................................................19
8.2 My settings are lost after re-starting the system. ...................................................19
Manuale d’uso ORDERMAN
-Touch Terminal
- 4 -
Italiano
OM-TT customer
VFD 140 x 16 Dots (Op-
Integrated Ordercardreader
(option)
SVGA TFT-Display
Waiterloc
k (Option)
Tool-
MenuCard
ON/OFF Button
1 Introduction of the ORDERMAN
-Touch Terminal
The ORDERMAN-Touch Terminal contains the following interfaces:
External interfaces: Internal interfaces for optional hardware:
1x Ethernet 100Mbit, 100 Base-TX, RJ45 1x Waiterlock
4x Serielle Ports RS232, RJ 11 1x OM-TT customer VFD 140 x 16 Dots
1x PS/2 keyboard 1x ORDERCARD
reader
1x Compact Flash Card Type 1
1x USB-Slave
ORDERMAN
-Touch Terminal Manuale d’uso
- 5 -
Italiano
Pin 1…RTS
Pin 2…TxD
Pin 3…RxD
Pin 4…CTS
Pin 5…GND
Pin 6…NC
NC... Not connected
Pin 1
Pin assignement of the serial
ports
The location of the interfaces can be found
on the serial number sticker.
Scancode 101
Scancode 102
Scancode 103
Scancode 104
Scancode 105
2 The MenuCard
The MenuCard (e.g. figure on the right) is part of the
ORDERMANTouch Terminal and can be configured
for your specific purpose.
Use the ORDERMANMenuCardDesigner to create
your MenuCard.
(Detailed description for using the ORDERMAN
MenuCardDesigner see its online help)
2.1 The ORDERMAN
Toolbar
The Toolbar contains five buttons with fix
Scancode which can be used for your specific
purpose.
Manuale d’uso ORDERMAN
-Touch Terminal
- 6 -
Italiano
3 The Operating system of the ORDERMAN
-Touch
Terminal
The ORDERMAN-Touch Terminal is running Microsoft WindowsCE 4.2, so working is com-
parable to your desktop PC. Here only some parts of Windows are brought up for a detailed
description of Microsoft WindowsCE see the Microsoft Help (see “3.3.2 Help”).
3.1 The Windows CE licence
The Microsoft Windows CE licence can be found on the sticker on the bottom side of your
ORDERMAN-Touch Terminal.
3.2 The Desktop
The Desktop is the screen that is displayed after starting the ORDERMAN-Touch Terminal.
The Desktop contains things like the Start Menu or Links.
For adding a link to the Desktop see “5.12 Add a Link to the Desktop”
Start Menu
and Taskbar
Taskbar Icons
Version of the Operating S
y
s-
tems image
The number can deviate from
the number displayed here.
Link
s
ORDERMAN
-Touch Terminal Manuale d’uso
- 7 -
Italiano
3.3 The Start menu
The Start menu contains the following items which are described below.
Programs
Favorites
Documents
Settings
Help
Run
3.3.1 Run
Run is used to launch programs.
3.3.2 Help
Via the Help link you can open the Microsoft WindowsCE Help which contains
common Help topics like connecting to a local area network.
3.3.3 Settings
The Settings folder contains links to
• Control Panel (see “3.7 The Control Panel”)
• Network and Dial-Up Connections (see “5.1 Connect
the OM-TT to a Local Area Network”)
• Taskbar and Start Menu (see Microsoft Help).
3.3.4 Programs
The Programs section of the Start Menu contains
this entries by default.
• Command Prompt: starts the DOS shell for
those who dislike the Windows Explorer.
• Installation Backup: see “5.5 Install a
program”
• Internet Explorer: visit the www (see Microsoft Help)
• Registry Backup: see “5.7 Save system settings / changes in the registry”
• Registry Editor: see “5.3 Use the Registry Editor”
• Remote Desktop Connection: see “5.15 Use Remote Desktop / RDP”
• Windows Explorer (see Microsoft Help)
3.4 The Taskbar Icons
Manuale d’uso ORDERMAN
-Touch Terminal
- 8 -
Italiano
The ORDERMANTouch Terminal is connected to a LAN. (see “5.1 Connect
the OM-TT to a Local Area Network”)
The LAN connection is interrupted (see “5.1 Connect the OM-TT to a Local Area Network”)
The OMTTHWManager is running. (see “6.8 OMTTHWManager”
Tapping this button brings the Desktop to the front.
The MyComputer link leads you to the root directory of your ORDERMAN Touch
Terminal.
Here you can access e.g. the FlashDisk or the Harddisk/CompactFlash Card
(option). For using MyComputer respectively the Windows Explorer see the Mi-
crosoft Help.
Large Keyboard
3.5 The Input Panel
The Input Panel is a virtual keyboard on your screen which
can be used, for example, to enter a password without
connecting a real keyboard to your ORDERMANTouch
Terminal.
3.6 MyComputer
3.7 The Control Panel
You can access the Control Panel via the link in the Start Menu (see3.3
The Start menu) or through MyComputer and the Windows Explorer.
The Control Panel allows users to set
a variety of system-wide properties,
such as network setup, and the
desktop color scheme.
For a detailed description of the
Control Panel see the Microsoft Help.
4 Saving files and settings (registry)
A
n Active Sync connection is established. See “5.2 Active Sync”
e Input Panel”)
The Taskbar Icons section can deviate from this figure, this depends
on the programs running on the ORDERMANTouch Terminal.
Tip
ORDERMAN
-Touch Terminal Manuale d’uso
- 9 -
Italiano
Files copied to the
Flashdisk directory are
save in case of a system
restart.
The Flashdisk, the Harddisk (optional Com-
pactFlash card) can be used to save your
data.
A
ll other directorys are placed in RAMDisk
and are not safe in case of a system restart.
Caution
After committing changes in the Systemsettings call the Registry Backup. See
„5.7 Save system settings / changes in the registry“
The ORDERMANTouch Terminal consists of a RAMdisk, a Flashdisk and an optional
Harddisk (CompactFlash card).
This is important if you want to make changes to the system (e.g. Create a link on the Desk-
top), the registry or install any software.
All settings, files and folders except the Flashdisk and the Harddisk (CompactFlash card) are
saved in RAMdisk. This means everything installed into RAMdisk that don’t belong to the
default image of WindowsCE is lost after a restart of the system or a power failure (blackout).
5 HowTo
5.1 Connect the OM-TT to a Local Area Network
Connect the ORDERMANTouch Terminal to your network by using a network cable.
Caution
• Although you install something to the Flashdisk or Harddisk with an instal-
lation routine, some files may be copied to the Windows directory (RAM-
Disk). To avoid to loose this data you have to run Installation Backup (Start
=> Programs => Installation Backup).
• If you change settings e.g. if you change the background image on the
Desktop, you have to save the registry with the Registry Backup tool
(Start => Programs => Registry Backup).
• If you don’t use the installed registry editor to change the registry you have
to save the registry with the Registry Backup tool witch can be found in the
Programs section of the Start Menu (Start => Programs => Registry
Backup).
Manuale d’uso ORDERMAN
-Touch Terminal
- 10 -
Italiano
Open the Control Panel (see “3.7 The Control Panel”) and double tap the
Network and Dial-up Connection button.
Open the settings for the Network connection by double tapping the button.
The grey icon indicates that Active Sync is available.
The Active Sync icon changes to connected (green).
If you are asked to set up a partnership select
“NO”.
A
fter that you can access the ORDERMAN
Touch Terminal with your Explorer or the
Explore button in the Active Sync Window.
You need at least Active Sync V3.7.
Tip
If your network uses DHCP select “Obtain an IP address via DHCP”, otherwise enter a cor-
rect IP Address and Subnet Mask to the form.
For details and questions about
networks, DHCP or which IP Address to
use see Microsoft Help and/or ask you
network administrator.
5.2 Active Sync
Active Sync is a program used to synchronize your device to a Desktop PC and/or a Server.
You can download Active Sync from the Microsoft homepage.
Connect the ORDERMANTouch Terminal to your PC by using an USB cable.
ORDERMAN
-Touch Terminal Manuale d’uso
- 11 -
Italiano
If you install anything on the ORDERMAN Touch Terminal you have to
copy/install it to the Flashdisk or the Harddisk and run the Installation
Backup. Otherwise it is not guaranteed that the installed program
works correct. (see 4 Saving files and settings (registry) for details).
Tip
5.3 Use the Registry Editor
Launch the Registry Editor out of the “Programs” section of the “Start Menu” or the “Re-
gEditSave” shortcut in the “My Computer” section.
After changing the registry settings you have to save the changes to the flashdisk.
This can be done by tapping “Registry Backup” in the “Programs” section of the “Start Menu”.
5.4 Install a Compact Flash Card
The CompactFlash Card slot on the ORDERMANTouch Terminal is NOT “Hot Plug&Play”.
This means you have to disconnect power before inserting a CF card.
5.5 Install a program
Copy the files to the ORDERMANTouch Terminal by using e.g. an ActiveSync connection.
You can also copy it to a CompactFlash card (option).
Install the files to Flashdisk or Harddisk.
After the installation has completed you have to ini-
tiate a backup copy of files copied to the windows
directory and save registry settings.
Tap Start => Programs => Installation Backup.
(see “4 Saving files and settings (registry)”for details)
5.6 Remove a program
• Select the program you want to uninstall in the list by
tapping on it.
• Tap the “Remove” button in the dialog.
Select the Remove Programs button in the Control Panel. (How to enter
the Control Panel see 3.7 The Control Panel)
Only programs which were installed with an installation routine (*.cab
files) are listed up here.
Tip
Manuale d’uso ORDERMAN
-Touch Terminal
- 12 -
Italiano
Information for developers:
There are two ways to change the Menucard:
• You can use the OMTTHWHandler to change the MenuCard by software
(see its documentation for details).
• Copy the “omtt.bly” file to Flashdisk\ORDERMAN\MenuCard and replace
the existing file. After that tap the LoadMC link. Now you can use the new
MenuCard file.
Information
The name of the MenuCard file has to be “omtt.bly”.
Tip
• Tap “Yes” to confirm that the program is removed.
• After the program is uninstalled call the Installation Backup out of the Programs sec-
tion in the Start Menu. This is required to delete the backup files of the installation.
(“4 Saving files and settings (registry)“ for details).
5.7 Save system settings / changes in the registry
See “4 Saving files and settings (registry)”
To ensure that your changes in system settings (e.g. You have set the Taskbar to be always
visible or changed the view options of the Explorer) are available after restarting the system
you have to call Registry Backup in the Programs section of the Start Menu.
5.8 Change the MenuCard
For details of the MenuCard see “2 The MenuCard” first.
You can only change the MenuCard if your software supports this feature. For details please
see its manual.
5.9 Change the Keyboard layout
For using a special character set on your keyboard e.g. the german “Ö” you have to change
the keyboard layout to this language.
See the table for available keyboard layouts.
The default keyboard layout is 00000407 - German.
For changing the Keyboard layout open the RegistryEditor in
the Programs section of the Start Menu.
Go to HKEY_CURRENT_USER => Keyboard Layout =>
Preload => 1
ORDERMAN
-Touch Terminal Manuale d’uso
- 13 -
Italiano
Double tip Default in the right column and
enter the Value of the keyboard layout you
want to use.
Tap OK to confirm your settings.
Close the RegistryEditor by tapping Exit in the Registry Menu.
After closing the Registry Editor you receive a message box. Tap Yes to save the registry to
internal flash. (for details see “4 Saving files and settings (registry)”)
5.10 Re-calibrate the touch
5.10.1 Calibrate by using the Control Panel
Select the Calibration tap in the Stylus
Properties and tap the “Recalibrate” but-
ton.
Follow the instructions on the screen
and save the calibration.
Exit the Stylus Properties with the “OK”
button. (For more information see the
Microsoft Help)
5.10.2 Shortcut to the touch calibration
• Tip and hold down anywhere on the touch.
• Switch Off the ORDERMANTouch Terminal with the ON/OFF button
(see “1 Introduction of the ORDERMAN-Touch Terminal”)
• Switch On again
• Release the touch.
• Now you are in the touch calibration mode. Follow the instructions on the screen.
• Save the settings after finishing calibration.
Layout Value
US 00000409
German 00000407
Spanish 0000040a
French 0000040c
Italian 00000410
Croatia 0000041a
Spanish int. 00000c0a
UK 00000809
Double tip the Stylus button in the Control Panel. (How to enter the Control
Panel see “3.7 The Control Panel”)
Use the ORDERMAN
-touch pen for calibration. Only precise calibra-
tion insures precise operation.
Tip
Manuale d’uso ORDERMAN
-Touch Terminal
- 14 -
Italiano
5.11 Starting Programs at Start Up
Copy your file or link to “\Flashdisk\Autostart”. This ensures that all optional hardware com-
ponents are available.
5.12 Add a Link to the Desktop
Create the link on the Desktop and run the Installation Backup.
For details how to create a link see Microsoft Help.
(See ” 4 Saving files and settings (registry)”)
5.13 Change the background image of the Desktop
• Go to the Desktop.
• Tip and hold down the touch.
• Open the properties.
• Tap the “Browse” button and
select a bitmap file (*.bmp)
• Tap “OK” and save the
changes to the registry with the
Registry Backup in the Pro-
grams section of the Start Menu.
You can also enter the display properties via the Control Panel.
The “Orderman_Logo.bmp” (background image) is saved in the “Windows” directory .
5.14 Hide the Taskbar
Open the “Taskbar and Start Menu” in the “Set-
tings” part of the “Start Menu”.
(Start => Settings => Taskbar and Start Menu)
In the properties uncheck the “Always on top”
control box and enable the “Auto Hide prop-
erty”.
5.15 Use Remote Desktop / RDP
Remote Desktop is used to connect to a terminal server or a computer running remote desk-
top. For details to RDP see Microsoft Help and/or ask your administrator.
For using Remote Desktop you need a computer running remote desktop Server and a net-
work connection. (see “5.1 Connect the OM-TT to a Local Area Network”).
ORDERMAN
-Touch Terminal Manuale d’uso
- 15 -
Italiano
Open the Remote Desktop Connection link on the Desktop or via the
Programs section in the Start Menu and Expand the Options section.
In the General tab you have to enter the IP – Ad-
dress of the remote Computer, your user name,
password to login and the domain you are working
in.
Here you can also save your connection settings.
Before opening you have to configure the connection.
• In the Display section of the Remote Desktop
Connection settings you can disable the con-
nection bar
• The Local Rescources section holds the settings for connecting the serial Ports or
your disk drives of the ORDERMANTouch Terminal to the remote computer.
• The Experience form holds the settings to optimize performance for your connection
speed
• In the Program section you can enter an application to run after connecting to the re-
mote Computer
After configuring you Remote Desktop Connection you have to save you setting.
5.15.1 Automatic start of the Remote Desktop Connection
Because the password isn’t saved in the configuration file, the ORDERMANTouch Terminal
uses a modified version of the RDP-client to simplify the start-up of your Remote Desktop
Connection. (cetsc.exe can be found in the windows directory)
Manuale d’uso ORDERMAN
-Touch Terminal
- 16 -
Italiano
Parameters to start CETSC.exe
To start the Remote Desktop Connection automatically use the following parameters:
/orderman:<password[:<connection file>]>
e.g. :
\windows\cetsc.exe /orderman:1234:\flashdisk\myRDPSettings.rdp
5.16 Restart the ORDERMAN
Touch Terminal
Hold down the ON/OFF Button (approximately 6 sec.) until you here the buzzer, than release
the ON/OFF Button.
5.17 Set the ORDERMAN
Touch Terminal back to factory defaults
This resets the settings / registry of your ORDERMANTouch Terminal. All installed pro-
grams are lost and must be re-installed. The Registry is set back to default.
• Go to “My Computer” (the root directory).
• Start “RegClear”.
• Follow the screen instructions.
6 Programs on the ORDERMAN
Touch Terminal
6.1 OM-TT Process Viewer
You can find the “OM-TT Process Viewer” in “My Computer”.
The OM-TT Process Viewer can be used to end running processes.
This tool is for software developers only.
Information
ORDERMAN
-Touch Terminal Manuale d’uso
- 17 -
Italiano
6.2 SDAuthUtilDevice
You can find it in “My Computer”
6.3 RegClear
You can find it in “My Computer”
This program resets the system. All installed programs and settings are lost.
See “5.17 Set the ORDERMANTouch Terminal back to factory defaults”
6.4 RegFlush
You can find it in “My Computer”.
“RegFlush” creates a backup of the registry.
6.5 RegEditSave
“RegEditSave” can be found in “My Computer”.
“RegEditSave” launches a registry editor, that automatically creates the backup for the regis-
try.
For details see “4 Saving files and settings (registry)”
6.6 Installation Backup / FileSystemWatcher
The “Installation Backup” link in the “Start Menu” starts the “FileSystemWatcher.exe”. This
Program can be found in the “Windows” directory. It is used to create a backup of installed
programs. For details see “4 Saving files and settings (registry)”
6.7 TextEditor
The “TextEditor” can be found in the “Flashdisk\ORDERMAN” directory.
6.8 OMTTHWManager
The “OMTTHWManager” is a software running on the ORDERMANTouch Terminal which
handles the optional hardware, the keyboard and the MenuCard. You can access the
“OMTTHWManager” with the “OMTTHWHandler” (part of the Integration Package provided
by Think Dig).
The following settings can be taken in the configuration file of the OMTTHWManager (Flash-
disk\ORDERMAN\OMTTHWManager\OMTTHWManager.exe.config)
This section is for software developers only.
Information
This tool is for software developers only.
Information
Manuale d’uso ORDERMAN
-Touch Terminal
- 18 -
Italiano
• ServerTCPSocketPort
The Port used be the OMTTHWManager. This has to go conform with the settings of the
OMTTHWHandler.
• StartupType
This starts the OMTTHWManager visible or hide.
• HardwarePort
This setting must not be changed.
• Transponder_Animation:
Enable or disables the animation during the Transponder is running. (the Transponder is
optional)
• AutoWaiterLockWakeUp
This enables or disables the waiter lock wake up.
7 Special Files/Folders on the ORDERMAN
Touch Ter-
minal
This files are necessary to guarantee that the ORDERMANTouch Terminal runs correct
and must not be changed.
• Windir.txt
• Omtt_menucardbuffer40_file
• OutOfTouch
• Flashdisk\Windows:
ORDERMAN
-Touch Terminal Manuale d’uso
- 19 -
Italiano
A System required folder that must not be changed.
• Flashdisk\ORDERMAN\
“Flahdisk\ORDERMAN\ “contains the following sub folders:
• \AVR: A System required folder that must not be changed.
• \MenuCard: This folder contains the definitions for your Menu Card.
See “2 The MenuCard” for details.
• \OMTTHWManager:
A System required folder that must not be changed.
See “6.8 OMTTHWManager” for details.
8 FAQ’s
8.1 What’s the Installation Backup good for ?
See “4 Saving files and settings (registry)”
The Installation Backup creates a backup file for your current settings and installed pro-
grams.
If you restart your ORDERMANTouch Terminal your settings are restored.
8.2 My settings are lost after re-starting the system.
See „4 Saving files and settings (registry)” section.
Table of contents
Other Orderman Touch Terminal manuals
