Organic Lighting Systems liniLED Top User manual

LED strip manual
liniLED® Top High Power
BEND
R
30 mm
F
FROST
RoHS
GLOW WIRE
850 °C
24
V D
C
SEA
IP40/IP68 UV POOL CL
CRI
80
+
IK08 CLEANING POOL CL
MAC
ADAM
2
S D C M

liniLED® Top High Power
Technical notes 4
Top High Power - Product drawings 5
Product information 5
Product specications 5
Cable selection 6
Area advice 7
Product care and handling 8
Cutting instructions 9
Solder 11
Connect IP40 13
Uninstalling the connector 15
Power supply 16
Symbols 17

4
LED strip manual | liniLED® Top High Power
Read the instructions and safety precautions before installation, usage and storage of the products to secure safety of the user and reliability of the product.
- Hand over the instructions to the end-user and those responsible for installation and usage.
- Triolight B.V. cannot be held responsible for improper handling, product installation, usage or storage.
Handling
- Handle with care.
- The product may not be modied or converted otherwise than prescribed.
- Products are transported in proper packaging. Products should remain packed until installation.
- Take ESD (Electrostatic Discharge) protection measures when handling liniLED® products.
- The products and their components may not be exposed to mechanical, static loads and other tension/compression other than from the product itself.
Installation
- Attention: The power has to be switched o the main power supply or the connection before installation. Not doing so may damage the product.
- Use a suitable LED power supply/driver: 24 V DC constant voltage. Do not drive the product on other voltages than described in their datasheet/products
specications.
- Installation has to be done by a certied professional with knowledge of electrical circuits or a specialised maintenance person known with valid directives.
- General and local construction-, safety- and installation regulations should be respected.
- Use only supplied parts, accessories and required tools as prescribed in the installation manual to guarantee a safe installation and use of the product.
- Products may solely be installed in the areas according to their prescribed IP-rating, IK-rating, temperature range and chemical resistances.
- Do not fasten anything on the product, same applies for hanging.
- Do not install the product in the following cases:
- Damage is visible on the product or its cables.
- The inside of the product is moistened or dirty.
- The product or its cables have been modied. It could lead to an electrical shock or a short circuit may occur.
- Children may not play unsupervised with electrical products as they cannot judge the dangers in dealing with electrical circuits correctly.
Operation and use
Solely use the product when its working correctly. If not, switch the power o immediately and advise an electrical specialist in the following cases:
- Damage is visible on the product.
- The product does not function.
- Smoke or steam rises from the product.
- Crackling sounds are noticeable.
- The product is overheating.
- Repairs on the installation may only be performed by qualied electricians. Product repairs may solely be done by Triolight B.V.
Cleaning and maintenance
- Attention: Disconnect the power before maintenance and cleaning.
- Dust and dirt accumulated over time should be removed from the light-emitting surface to assure optimal functioning of the product.
- Paints, solvents and corrosive cleaning chemicals may not contact and thus aect the product.
Environment and waste
- Exterior decorative lighting should only be used after sunset.
- This product may not be treated as household waste. Dispose of the material through the waste recycling of electrical and electronic equipment.
Warranty
This product comes with a 2 year warranty. Warranty void if:
- The installation guide has not been consulted (installation mistake).
- The installation is not done by a certied installer.
- Local rules and guidelines are not respected.
- The invoice cannot be shown and/or has been altered.
- Damage is caused by negligence, abnormal use or improper handling, use, maintenance and/or cleaning of the product.
Technical notes

5
LED strip manual | liniLED® Top High Power
The liniLED® Top High Power (HP) LED strip (IP40/IP68*) is a high quality, exible LED strip with a unique co-extrusion
technology. The combination of high quality and exceptional exibility, allows for an endless range of indoor and outdoor applications.
*For usage in wet enviroments, use the liniLED® IP68 Kit or mirror welded.
LED strip top view
LED strip front view
6
12
50
12
Product information
Product specications
Colour LED/m V DC W/m lm/m Temp ˚C Max. Length B50/L70
2400K 120 24 8.9 623 -30...5510 m > 60.000 h
2700K 120 24 8.9 703 -30...5510 m > 60.000 h
3000K 120 24 8.3 617 -30...5510 m > 60.000 h
4000K 120 24 8.6 711 -30...5510 m > 60.000 h
6500K 120 24 8.6 693 -30...5510 m > 60.000 h
Max. connection length between -20 °C and -30 °C is 7 metres.
Top High Power - Product drawings

6
LED strip manual | liniLED® Top High Power
1. Colour temperature 2400K - 2700K
2. LED strip length 1 m 2 m 5 m 10 m
3. Voltage 24 V DC 25 V DC 24 V DC 25 V DC 24 V DC 25 V DC 24 V DC 25 V DC
4. Cable cross section 0.50 mm - 0.035 Ω/m 33.5 m 65.5 m 16.1 m 32.1 m 5.6 m 12.0 m 2.1 m 5.4 m
0.75 mm - 0.023 Ω/m 50.4 m 98.6 m 24.2 m 48.3 m 8.5 m 18.1 m 3.3 m 8.1 m
1.00 mm - 0.018 Ω/m 67.0 m 131.1 m 32.2 m 64.2 m 11.3 m 24.1 m 4.3 m 10.8 m
1.50 mm - 0.012 Ω/m 100.9 m 197.2 m 48.5 m 96.7 m 17.0 m 36.3 m 6.6 m 16.2 m
2.50 mm - 0.007 Ω/m 167.9 m 328.3 m 80.7 m 160.9 m 28.4 m 60.5 m 11.0 m 27.0 m
1. Colour temperature 3000K
2. LED strip length 1 m 2 m 5 m 10 m
3. Voltage 24 V DC 25 V DC 24 V DC 25 V DC 24 V DC 25 V DC 24 V DC 25 V DC
4. Cable cross section 0.50 mm - 0.035 Ω/m 36.0 m 70.4 m 17.3 m 34.5 m 6.1 m 13.0 m 2.4 m 5.8 m
0.75 mm - 0.023 Ω/m 54.2 m 105.9 m 26.1 m 51.9 m 9.3 m 19.6 m 3.6 m 8.8 m
1.00 mm - 0.018 Ω/m 72.1 m 140.8 m 34.7 m 69.1 m 12.3 m 26.1 m 4.8 m 11.7 m
1.50 mm - 0.012 Ω/m 108.4 m 211.8 m 52.3 m 103.9 m 18.6 m 39.2 m 7.3 m 17.7 m
2.50 mm - 0.007 Ω/m 180.5 m 352.5 m 87.0 m 173.0 m 30.9 m 65.3 m 12.2 m 29.4 m
1. Colour temperature 4000K - 6500K
2. LED strip length 1 m 2 m 5 m 10 m
3. Voltage 24 V DC 25 V DC 24 V DC 25 V DC 24 V DC 25 V DC 24 V DC 25 V DC
4. Cable cross section 0.50 mm - 0.035 Ω/m 34.7 m 67.9 m 16.7 m 33.3 m 5.9 m 12.5 m 2.3 m 5.6 m
0.75 mm - 0.023 Ω/m 52.2 m 102.1 m 25.1 m 50.1 m 8.9 m 18.8 m 3.4 m 8.4 m
1.00 mm - 0.018 Ω/m 69.5 m 135.8 m 33.4 m 66.6 m 11.8 m 25.1 m 4.6 m 11.2 m
1.50 mm - 0.012 Ω/m 104.5 m 204.3 m 50.3 m 100.2 m 17.8 m 37.7 m 6.9 m 16.9 m
2.50 mm - 0.007 Ω/m 174.0 m 340.0 m 83.7 m 166.7 m 29.6 m 62.8 m 11.6 m 28.2 m
Note: Calculations are based on a standard connector with 1 metre cable (0.5 mm).
1= Select colour temperature.
2 = Select LED strip length.
3= Select output voltage.
4= Select cable cross section.
Result = Maximum cable length based
on the cable thickness and power supply
voltage.
Cable selection
-+
Top/Side Connector (1000 mm)
1
2
3
4
Result
Cable selection

7
LED strip manual | liniLED® Top High Power
Depending on the area where the liniLED® LED strip is installed we oer a range of solutions to cope with external factors. The product portfolio includes a
range of IP40 and IP68 connectors. Below the dierent connectors are displayed for use in dierent environments.
Indoor environment | (IP20)
Solder
Submersible, chlorine resistant | (IP68) |Mirror Welded Connector
Product code: 11290
Indoor environment | (IP40) | liniLED® Top Connector set
Product code: 11200 (1m), 11201 (5m)
Wet environment | (IP67) | liniLED® Top IP67 Kit
Product code: 11506
Area advice

8
LED strip manual | liniLED® Top High Power
30 mm
30 mm
Maximum bending radius is 30 mm. Solely bend up or downward. Do not compress or stretch the LED strip.
Do not bend the LED strip sidewards. Do not twist the LED strip.
The LED strip has to be unreeled on a horizontal surface at the time of installation. Do not unreel the spool of LED strip before installation.
Product care and handling

9
LED strip manual | liniLED® Top High Power
Work in an ESD protected environment. Make use of an anti-static
strap.
Turn o the power before cutting the LED strip.
Side view | Make sure the cut is vertical as illustraded in the image
above.
Top view | Make sure the cut is vertical as illustraded in the image
above.
Top view | Only cut on the dotted lines to prevent damaging the LED
strip.
Dispose of the unnecessary material through waste recycling of
electrical and electronic equipment.
Cutting instructions
5
3
2
4
6
1

10
LED strip manual | liniLED® Top High Power
Place the liniLED® LED strip on the base of the cutting tool. Not doing so may result in a deformed LED strip.
Cutting instructions
7

11
LED strip manual | liniLED® Top High Power
Work in an ESD protected environment. Make use of an anti-static
strap.
Turn o the power. Make sure the wires are not under electric
current.
0.5 mm
2
8 mm
Solder the wires to the PCB. We advise to use a cable with an area not
higher then 0.5 mm
Top view | Only cut the LED strip extrusion on the dotted line of
the extrusion to prevent damaging the PCB. Carefully cut away this
part of the extrusion.
Side view | Do not cut the PCB! The end result after cutting the LED strip extrusion should look
similar to the image above.
Solder
5
3
2
4
6
1

12
LED strip manual | liniLED® Top High Power
350 C
Pre-solder the connector pads. Pre-solder the wires.
Solder the wires to the connector pads. Connect the liniLED® LED strip to the power supply (24 V DC) con-
stant voltage.
Solder
9
8
10
7
350 C
350 C

13
LED strip manual | liniLED® Top High Power
1
2
3
4
The liniLED® IP40 Connector consists of: End cap (1), Shell (2),
Connector (3), Clamp (4).
Take into account the direction of the arrow on the bottom of the
liniLED® LED strip and allign it with the arrow on the clamp (4).
Place the shell (2) over the LED strip. Make sure the side with the small-
est opening is put on rst.
Side view | Slide the clamp (4) over the cable to reveal the
connector (3).
Slide the connector (3) sideways into the hollow chamber of the
liniLED® LED strip. Side view | Do not cut the PCB!
Front view | Make sure the connector and the PCB are perfectly
horizontally alligned.
Connect IP40
5
3
2
4
6
1

14
LED strip manual | liniLED® Top High Power
Slide the clamp (4) over the connector (3) and make sure that the
arrow is on the upper side.
Slide the shell (2) partly over the clamp (4).
‘ Click ’
Test the liniLED® LED strip before you slide it fully over the clamp (4). Slide the shell (2) entirely over the clamp (4) and push rmly until it
‘clicks‘.
Finish the connection by inserting an end cap (1) in the hollow
chamber on the end side of the liniLED® LED strip.
Connect IP40
11
9
8
10
7

15
LED strip manual | liniLED® Top High Power
Firmly grab the outer shell and gently grab the liniLED® LED strip. Gently wiggle the connector and pull in opposite direction.
The connector should look like this when it is removed. Firmly press the sides of the shell and pull gently while holding the
cable to remove it.
Article number Description
11200 liniLED® Top Connector set 1 m
11201 liniLED® Top Connector set 5 m
11208 liniLED® Top Extension Cord
Uninstalling the connector
5
3
2
4
1

16
LED strip manual | liniLED® Top High Power
Turn o the power before connecting the LED strip to the power
liniLED® LED Driver
(Optional)
L
N
liniLED® Power Supply
24 V DC
-+
230 V AC
IP40
IP40
IP67
Connect the LED strip as indicated in the gure above. The wires should be connected as follows: Red (+) and Black (-).
Insert the power plug.
Power supply

17
LED strip manual | liniLED® Top High Power
Manufacturer’s declaration that the product meets the applicable EC directives.
Bending of the LED strip is possible with a radius of ≥ x millimetres in the specied direction.
BEND RADIUS
R
X mm
GLOW WIRE
850 °C
Passed glow wire test at 850 degrees Celsius. Global European regulations specify 650 degrees Celsius by default.
Electrical appliance class III: this product is designed to be supplied from an extra-low voltage (≤ 60.0 V DC or ≤ 42.4 V AC).
This product can be applied in seawater and its environment. Elements in seawater will have no harmful eect on the product.
For chemical specications see datasheet. Verify the IP rating for proper use.
SEA
This product can be both IP40 and IP68 depending on the conguration and application. See the documentation for the exact IP rating.
IP40/IP68
Product can be cleaned with normal cleaning agents as specied in the datasheet under ‘chemical compliances’.
CLEANING
This product is available on request and can be applied submerged in swimming pools and their environment. Disinfectants will have
no harmful eect on the product. For chemical specications of these elements see datasheet. Verify IP rating for proper use.
POOL CL
MAC
ADAM
2
S D C M
The binning tolerance of this product is 2 MacAdam.
FSuitable for mounting on all surfaces and suitable to cover with insulating material.
Operating voltage of 24 V DC.
24
V D
C
RoHS
Restriction of Hazardous Substances (RoHS): product complies with the RoHS directive and each homogeneous material does not exceed
the limits for the materials mentioned under the RoHS directive (Pb, Hg, Cd, Cr6+, PBB and PBDE).
Product is resistant against ultraviolet (UV) light or sunlight. Non-UV resistant products can degrade or discolor fast when exposed to UV light.
UV
This product can be applied inside swimming pool environments. Elements in the air will have no harmful eect on the product.
For chemical specications of these elements see datasheet. Verify IP rating for proper use.
POOL CL
The CRI value of this product is 80 or higher.
CRI
80
+
Protected against impact energy of 5 joules.
IK08
This product can be stored and used below 0 degrees Celsius. Verify the minimum storage and operation temperature in the datasheet or manual
for the lowest temperature allowed.
FROST
Symbols

Disclaimer
The published information is checked to be as accurate as possible, however Triolight B.V. or any reseller of liniLED® cannot be held liable for any damages resulting
from errors or outdated information. Triolight B.V. reserves the right to modify the information without informing the customers. When this document is printed or
downloaded, please check for the latest version on the internet, the most up to date information will be published on www.liniLED.com. This product should not
be used in applications, devices or systems where incorrect operation of the product may result in personal injury (includes emergency lighting) without written
permission from the board of Triolight B.V. If nevertheless used in such applications, devices or systems Triolight B.V. cannot be held liable for any resulting injury.

liniLED® is a registered trademark of Triolight B.V.
Subject to misprints, errors and modications. No legal rights can be derived from this document. V1218