Oriental motor MD Series User manual

Introduction
■Before using the product
Only qualied personnel of electrical and mechanical engineering should work with the
product. Use the product correctly after thoroughly reading the section "Safety precautions."
In addition, be sure to observe the contents described in warning, caution, and note in this
manual.
The product described in this document has been designed and manufactured to be
incorporated in general industrial equipment. Do not use for any other purpose. For
the power supply, use a DC power supply with reinforced insulation on its primary and
secondary sides. Oriental Motor Co., Ltd. is not responsible for any damage caused through
failure to observe this warning.
Safety precautions
The precautions described below are intended to ensure the safe and correct use of the
product, and to prevent the user and other personnel from exposure to the risk of injury. Use
the product only after carefully reading and fully understanding these instructions.
WARNING
Handling the product without observing the instructions that
accompany a "WARNING" symbol may result in serious injury or death.
CAUTION
Handling the product without observing the instructions that accompany
a "CAUTION" symbol may result in injury or property damage.
Note The items under this heading contain important handling instructions
that the user should observe to ensure safe use of the product.
[Description of
graphic symbols] : Indicates "prohibited" actions that must not be performed.
: Indicates "compulsory" actions that must be performed.
WARNING
•Do not use the product in explosive or corrosive environments, in the presence of
ammable gases, locations subjected to splashing water, or near combustibles.
Doing so may cause re or injury.
•Do not transport, install, connect, or inspect the product while the power is supplied.
Always turn o the power before carrying out these operations. Injury may result.
•Do not forcibly bend, pull or pinch the lead wire. Doing so may result in re.
•Do not disassemble or modify the fan. Doing so may cause injury.
•Only qualied and educated personnel should be allowed to perform installation,
connection, operation and inspection/troubleshooting of the product. Handling by
unqualied and uneducated personnel may result in re or injury.
•Keep the input-power voltage within the specied range. Failure to do so may result
in re.
•For the power supply, use a DC power supply with reinforced insulation on its
primary and secondary sides. Failure to do so may result in electric shock.
•Perform connections securely according to the connection diagram. Failure to do so
may result in re or a skin burn(s).
•Shut o the power to the fan in the event the rotating part (blades) is locked during
operation and the burnout prevention circuit is activated. Otherwise, the fan will
start unexpectedly when released from the locked condition. This may cause injury
or damage to equipment.
•Turn o the power in the event of a power failure. Otherwise, the fan will start
unexpectedly when the power is restored. This may cause injury or damage to
equipment.
CAUTION
•Do not use the fan beyond its specications. Doing so may result in injury or
damage to equipment.
•Keep your ngers and objects out of the openings in the fan. This may cause injury.
•Do not lift the fan by holding the rotating part (blades) or lead wires of the fan.
Doing so may cause injury.
•Do not remove the lead wire of the fan from the frame hook. Doing so may cause
damage to the lead wire.
•Keep the area around the fan free of combustible materials. Failure to do so may
result in re or a skin burn(s).
•Do not leave anything around the fan that would obstruct ventilation. Doing so may
result in damage to equipment.
•Do not touch the rotating part (blades) while operating. Doing so may cause injury.
The use of the nger guard is recommended to ensure protection.
•Before installing the fan, take measures against static electricity. Failure to do so
may result in damage to equipment.
•Immediately when trouble has occurred, stop operation and turn o the power
supply. Failure to do so may result in re or injury.
•Securely install the fan in an enclosure. Failure to do so may result in injury or
damage to equipment.
Checking the product
■Package contents
Verify that the items listed below are included. Report any missing or damaged items to the
branch or sales oce from which you purchased the product.
□Fan .................................................... 1 unit Fan speed controller (Sold separately)
Model: FSC-24
This is a speed controller for the
exclusive use of the Vtype fans. It
can easily change the duty of the
Pulse-Width Modulation (PWM)
signal using the setting dial.
□OPERATING MANUAL................1 copy
(this document)
■Checking the model name
Verify the model name of the purchased product against the model shown on the name
plate of the product.
Tell us the model name, product serial number, and manufacturing date shown on the name
plate when you contact us.
MD V 12 38 - 24 S
①②
③⑤⑥
④
Fan size
①Series name MD: MD Series
②Type V: Vtype (variable ow)
③Frame size
④Frame thickness
⑤Rated voltage 24: 24 VDC
⑥Additional function S: Pulse sensor
Installation
■Installation location
Install the product in the following location that provides easy access for inspection.
•Inside an enclosure installed indoors
•Operating ambient temperature: −10 to +60 °C [+14 to +140 °F] *
(non-freezing, non-condensing)
Operating ambient humidity: 20 to 85% *(non-condensing)
* The operating ambient temperature and operating ambient humidity vary depending
on the product. Check on the Oriental Motor Website for the product specications.
•Area that is free of explosive atmosphere or toxic gas (such as sulfuric gas) or liquid
•Area not exposed to direct sun
•Area free of excessive amount of dust, iron particles or the like
•Area not subject to splashing water (rain, water droplets), oil (oil droplets) or other liquids
•Area not subject to continuous vibration or excessive shocks
•Area free of radioactive materials, magnetic elds or vacuum
•Area free of excessive electromagnetic noise (from welders, power machinery, etc.)
When using near a switching circuit or high-frequency power supply, the induced current
may ow inside the fan due to electromagnetic noise (conductive noise, radiative noise).
If the induced current ows, the electric corrosion is caused in the bearings of the fan. As a
result, it may generate the noise or shorten the service life of the products. Use the fan in
the environment that the electromagnetic noise does not cause.
■Installation method
•Install the fan onto an appropriate at metal plate having excellent vibration resistance
and heat conductivity.
•Drill mounting holes in equipment, and secure the fan using screws.
•For directions of the air ow and blades rotation, see the arrow indicated on the side of
the fan frame.
•Finger guards that can prevent ngers and foreign particles from entering are available as
peripheral equipment (sold separately). Install as shown in the gure when using.
Fan size Screw size Tightening
torque
Finger guard
(sold separately)
Mounting sc
rews
(not supplied)
420 M3 0.4 N·m
(3.5 lb-in)
515*, 625,
825, 925,
1225, 1238
M4 0.6 N·m
(5.3 lb-in)
* When the nger guard is used, the
screw size and tightening torque are
M3 and 0.4 N·m (3.5 lb-in), respectively.
HF-3170-2
OPERATING MANUAL Thank you for purchasing an Oriental Motor product.
This Operating Manual describes product handling procedures and safety precautions.
•Please read it thoroughly to ensure safe operation.
•Always keep the manual where it is readily available.
DC Axial Flow Fans MD Series
V Type (variable ow)

Connection
■Connecting the power supply
Verify the voltage specication with the nameplate of the product, and input the suitable
voltage.
Note A voltage applied to the fan may be higher than the output voltage of the DC
power supply depending on the wiring distance between the fan and the DC
power supply. Use the fan in a state where a voltage applied to the fan does not
exceed the voltage specication.
[Connection diagram]
DC power supply
for driving
+
– (GND)
Pulse sensor output
Red
Black
Yellow
PWM signal input
Brown
•Lead wire size: AWG26*
* The lead wire size of MDV1225 and 1238 are AWG24.
■Connecting the I/O signals
PWM signal input for speed control
The rotation speed of the fan can be adjusted by changing the duty cycle of the PWM signal.
The PWM signal can be used with equipment having a TTL output, open collector output, or
open drain output.
GND of the DC power supply for driving and that of the PWM signal are common.
PWM signal
Brown
Black
I source
Fan
I sink
R
R
0 V
• Specications of input signals
V
H
VL
TH
T
PWM duty cycle (%) =
×100
TH
T
PWM frequency 25 (kHz) =
1
T
V
H
= 4.75 to 5.25
V
VL= 0 to 0.4 V
Current source (I source): 1 mA or less (when PWM signal 0 V is input)
Current sink (I sink): 1 mA or less*(when PWM signal 5.25 V is input)
* Current sink (I sink) for MDV1238 only: 3 mA or less
When the PWM signal input is not connected, the fan rotates at the maximum rotation speed.
Pulse sensor output
This is a sensor that outputs a square wave signal with two cycles per revolution. The rotation
speed can be detected.
GND of the DC power supply for driving and that of the pulse sensor are common.
Yellow
Black
Fan
User's circuit
R
10 mA
or less∗
GND
30 VDC or less
∗
0 V
* 27.6 VDC or less and 5 mA or less for MDV420 and 515.
Operation
The fan starts rotating when the DC power supply is turned on.
■Setting the rotation speed
The rotation speed varies according to the duty cycle of input PWM signals. Increasing the
duty cycle makes the rotation speed faster, and the airow - static pressure increases.
Setting range
0204060
100
80
PWM Duty [%]
Rotation speed [r/min]
Low
High
①
②
①
②
Setting
range
Fan size PWM duty
①420, 515, 1238 20 to 100% *
②625, 825, 925, 1225 0 to 100%
* If the PWM duty cycle falls below 20%, the fan
may not rotate. Use the fan in a state of the
PWM duty of 20% or more.
The PWM duty - Rotation speed characteristics
vary depending on the product.
For details, check on the Oriental Motor Website.
Overheat protection for locked condition
This fan is equipped with a built-in burnout prevention circuit. Since this circuit automatically
controls the current ow to the windings when a locked condition is detected, it prevents
the fan from burning out.
The fan resumes operation automatically as soon as it is released from the locked condition.
Turn o the power at the time of inspections.
Inspection and maintenance
■Inspection
It is recommended that periodic inspections for the items listed below are conducted after
each operation.
If an abnormal condition is noted, discontinue any use and contact your nearest Oriental
Motor sales oce.
zInspection item
•Check if any of the mounting screws of the fan is loose.
•Check if the fan generates unusual noises.
■Warranty
Check on the Oriental Motor Website for the product warranty.
■Disposal
Dispose the product correctly in accordance with laws and regulations, or instructions of
local governments.
Specications
Check on the Oriental Motor Website for the product specications.
Regulations and standards
■UL Standards, CSA Standards, EN Standards
Applicable standards Certication body
UL 507 UL
CSA C22.2 No.113
EN 60950-1 TÜV
•Thermal class
UL/CSA Standards: 105(A) EN Standards: 120 (E)
zInstallation conditions (EN Standards)
For incorporating in equipment Overvoltage category:Ⅰ
Pollution degree: 2 Protection against electric shock: ClassⅢequipment
■RoHS Directive
The products do not contain the substances exceeding the restriction values of RoHS
Directive (2011/65/EU).
•Unauthorized reproduction or copying of all or part of this manual is prohibited.
•Characteristics, specications and dimensions are subject to change without notice.
•and are registered trademarks or trademarks of Oriental Motor Co.,
Ltd., in Japan and other countries.
© Copyright ORIENTAL MOTOR CO., LTD. 2019
Published in October 2019
T
echnical Support Tel:[phone]
8:30
A.M. to 5:00 P.M., P.S.T. (M-F)
7:30
A.M. to 5:00 P.M., C.S.T. (M-F)
www
.orientalmotor.com
Schiessstraße 44, 40549 Düsseldor
f, Germany
T
echnical Support Tel:[phone]
www
.orientalmotor.de
T
el:01256-347090
www
.oriental-motor.co.uk
T
el:01 47 86 97 50
www
.orientalmotor.fr
T
el:02-93906346
www
.orientalmotor.it
T
el:[phone]
www
.orientalmotor.com.br
• Please contact your nearest Oriental Motor oce for further information.
4-8-1Higashiueno
,Taito-ku,Tokyo 110-8536
Japan
T
el:03-6744-0361
www
.orientalmotor.co.jp
Tel:[phone]
www.orientalmotor.com.tw
Singapore
Tel:[phone]
www.orientalmotor.com.sg
Tel:[phone]
www.orientalmotor.com.my
Korea
Tel:[phone]
www.inaom.co.kr
Tel:[phone]
www.orientalmotor.co.th
Tel:[phone]
www.orientalmotor.com.cn
Tel:[phone]
www.orientalmotor.co.in
Hong Kong Branch
Tel:[phone]