Original BTC 7672 User manual

Exterior Bracket Light
Instruction Manual
7672 / 7677
Safety & Installation Instructions
1. If you are in any doubt consult a qualified electrician as to the installation of the fitting. Install in accordance with current
IEE wiring regulations. It is recommended that this fitting is installed by a qualified electrician.
2. Ensure that the electrical supply is OFF. Disconnect the electrical supply at the fuse-board.
3. If removing an existing fitting first, note all wiring connections: record which of the house wires is connected to the live,
neutral and earth terminals.
4. Carefully identify where the supply cable is (and check there are no other cables in the area) to avoid damage to concealed
wiring during installation.
5. Position the light where desired ensuring that there is suitable support adjacent to where you will connect to the house
supply and mark position of fixing holes, before drilling appropriate holes as below.
6. a. Brick or masonry: Drill holes into which the wall plugs tightly fit, then insert wall plugs.
b. Wood: No hole necessary (unless small pilot hole required), screws can be screwed directly into the timber.
c. Plaster/Cavity: Special cavity wall fittings are required, rather than provided fixings. These are widely available from
good hardware or DIY store and should come with their own instructions that must be followed. It may be easier to
relocate the fitting so that you screw directly into a timber joist or beam.
7. Support the fitting so that no strain is applied to the wiring when making the electrical connections. If necessary get a
colleague to help.
8. Electrical connection: this light fitting must be earthed. Make connections following the diagram below using the terminal
block provided. A small flat-head screwdriver is required.
9. To maintain the IP rating of this fitting, you must ensure that the electrical connection has suitable protection from water
ingress, housing the connection in an IP rated junction box or sealing the backplate with silicone.
10. Ensure that all electrical connections are tight, with no loose strands of wire left out of the connectors and the lid of the
connector is securely closed. Ensure there are no wires are trapped behind or within the fitting and complete the
installation, screwing the fitting to the mounting surface.
11. Fit the correct type and wattage of lamp (or less). Be careful not to overtighten the lamp.
12. Switch on at the fuse-board. Your light fitting is now ready for use.
Other Important Information
Switch off at mains before changing lamp(s). Never fit a lamp of greater wattage than recommended. Ensure children do not
play with the light fitting. Dispose of old lamps carefully. Never leave a fitting without a lamp in position (or someone can
accidently touch the contacts). Adjust fitting only when power to the fitting is off and has been left to cool. If the electrical flex
or electrical components become damaged at any point, power to the fitting should be disconnected immediately and not
operated until the damaged parts are fixed/replaced.
These instructions are provided for your safety in order to prevent the risk of Fire, Electric shock or Injury. It is vitally
important that they are read in their entirety before installing your fitting. Please retain for future reference.
MADE IN BRITAIN
ORIGINALBTC.COM
[phone]
UNIT 21 / 22 AVENUE ONE, STATION LANE, WITNEY, OX28 4XZ, ENGLAND
Exterior Bracket Light, 60W
Round Backplate
7677/060
Exterior Bracket Light, 100W,
Round Backplate, Swan Neck
7672/100
Exterior Bracket Light, 60W,
Round Backplate
7672/060
Exterior Bracket Light, 100W,
Round Backplate, Swan Neck
7677/100
L
N
Live
KEY
Neutral
Earth
L =
N =
=
*Mains
Supply
Fitting
*After 2004, wiring installation colours changed:
LIVE Brown replaces Red
EARTH Green/Yellow sleeving
NEUTRAL Blue replaces Black
BROWN
GRN/YEL
BLUE
BROWN
GRN/YEL
BLUE
Established in 1990, Original BTC manufactures relaxed, familiar lighting for traditional and contemporary homes.
All products are hand-assembled in Oxford from high quality components, produced in the UK.
Cleaning and Maintenance
Metal finishes should only be cleaned with a soft, dry cloth. Do not use polishes or abrasives. Glass can be cleaned by hand,
using a soft damp cloth with a diluted mild detergent (nonabrasive) or sutiable glass cleaner if necessary. Switch off power to
the fitting before cleaning. Spare parts are available for this product, please contact us on the details below.
Exterior Bracket Light, 60W,
Corner Fork
7672/060/AC
Exterior Bracket Light, 100W,
Corner Fork, Swan Neck
7672/100/SC
Exterior Bracket Light,
60W, Corner Fork
7677/060/AC
Exterior Bracket Light,100W,
Corner Fork, Swan Neck
7677/100/SC
v1.2-04.19

Exterior Bracket Light 7672 / 7677
PLEASE READ THE INSTRUCTIONS ON THE REVERSE BEFORE YOU BEGIN INSTALLING YOUR LIGHT
230V ac 50Hz Installation Diagram IP54
Exterior Bracket lights with right angle or swan neck (SN) arm. Available in galvanised or or black,
with a corner fork (CF) or a round base (RB). Galvanised guard sold separately.
(a) DP7672/60 and DP7677/60
(b) DP7672/100 and DP7677/100
DP7672/060 Bracket Light, 60W, RB
DP7672/100 Bracket Light, 100W, RB, SN
DP7672/060/AC Bracket Light, 60W, CF
DP7672/100/SC Bracket Light, 100W, CF, SN
DP7677/60 Exterior Bracket Light, 60W, RB
DP7677/100 Exterior Bracket Light, 100W, RB, SN
DP7677/60/AC Exterior Bracket Light, 60W, CF
DP7677/100/SC Exterior Bracket Light, 100W, CF, SN
Contents
1 - Backplate/Arm/Pan assembly
2 - Wide Gasket
3 - Narrow Gasket
4 - Reflector (7677) / Clips (7672)
5 - Well Glass
6 - 2 x Reflector screws*
7 - 4 x Fixing screws
8 - 4 x Rawl plugs
9 - Connector
10 - Corner Fork (optional)
11 - Galvanised wire guard (optional)
Required for Installation
-Screwdriver, flat-head
- Small screwdriver, flat-head
- Drill (if holes are required)
Install light as described overleaf and then assemble the rest of the light,
following the diagram on the opposite page.
- Ensure wide (60W) gasket/narrow gasket (100W) fits into the top of the pan (next to lampholder)
- Ensure the narrow gasket is positioned under the lip of the glass (and above reflector).
- Having inserted a light bulb, position the glass in the pan and then secure in place by attaching the reflector
(7677) or clips (7672) using the two pan screws. DO NOT OVER TIGHTEN SCREWS.
- The optional guard fits to the bottom of the reflector and is secured using the same pan screws that secure
the reflector (7677), clips (7672) to the pan. DO NOT OVER TIGHTEN SCREWS.
*If the light is to be installed in an exterior location, it is advised that a thin bead of sealant is applied around
the back plate to prevent water damage.
**If possible, make a recess in the wall behind corner fork bracket to make connection. If this is not possible,
chase/run the cable to alternative loaction where connection can be made, either directly through the wall the
fitting is being installed on, so the connection is made inside or to a location adjacent to the fitting, ensuring a
suitable exterior rated junction box is used to house the connection.
Installation and Assembly Instructions
2
3
4
5
6
Optional Extras
Wide gasket Narrow gasket
7
23
810 11
*Screws secure reflector and well glass in place. Loosen to allow removal of the reflector and glass when re-lamping.
Key
A Fixing Screws B Connector Block C Main Supply
E27 GLS BALL
LAMP GUIDANCE
TYPE* WATTAGE** BASE SHAPE




INCANDESCENT
CFL
ECO-HALOGEN
LED
60W MAX (a)
15W
28W
12W
* Warm white (2700k) low energy lamps recommended.
** Wattage value provided as a guide to suitable lamps. Lower wattage than stated may be used.
100W MAX (b)
20W
70W
18W
1
A B C
Apply Silicone around
corner fork bracket
where it meets wall.
A
B
C
60W versions
x2 Narrow gaskets
33
100W versions
Round Backplate Fixing Corner Fork Fixing
9