Original BTC DAVEY LIGHTING DP8034 User manual

Miniature Exterior Bulkhead Fitting
Instruction Manual
v1.1-04.19
Safety & Installation Instructions
1. If you are in any doubt consult a qualified electrician as to the installation of the fitting. Install in accordance with current
IEE wiring regulations. It is recommended that this fitting is installed by a qualified electrician.
2. Ensure that the electrical supply is OFF. Disconnect the electrical supply at the fuse-board.
3. If removing an existing fitting first, note all wiring connections: record which of the house wires is connected to the live,
neutral and earth terminals.
4. Carefully identify where the supply cable is (and check there are no other cables in the area) to avoid damage to concealed
wiring during installation.
5. Position the light where desired ensuring that there is suitable support adjacent to where you will connect to the house
supply and mark position of fixing holes, before drilling appropriate holes as below.
6. a. Brick or masonry: Drill holes into which the wall plugs tightly fit, then insert wall plugs.
b. Wood: No hole necessary (unless small pilot hole required), screws can be screwed directly into the timber.
c. Plaster/Cavity: Special cavity wall fittings are required, rather than provided fixings. These are widely available from
good hardware or DIY store and should come with their own instructions that must be followed. It may be easier to
relocate the fitting so that you screw directly into a timber joist or beam.
7. Support the fitting so that no strain is applied to the wiring when making the electrical connections. If necessary get a
colleague to help.
8. Electrical connection: this light fitting must be earthed. Make connections following the diagram below. A small flat-head
screwdriver is required.
9. Double check all the connections are secure and that no loose strands of wire are left out of the connector. Close the
terminal block lid securely for the GX53 version.
10. Check that no wires are trapped behind or within the fitting and complete the installation, referring to the Installation
diagram inside.
11. Fit the correct type and wattage of lamp (or less). Be careful not to overtighten the lamp.
12. Switch on at the fuse-board. Your light fitting is now ready for use.
Other Important Information
Switch off at mains before changing lamp(s). Never fit a lamp of greater wattage than recommended. Ensure children do not
play with the light fitting. Dispose of old lamps carefully. Never leave a fitting without a lamp in position (or someone can
accidently touch the contacts). Adjust fitting only when power to the fitting is off and has been left to cool. If the electrical flex
or electrical components become damaged at any point, power to the fitting should be disconnected immediately and not
operated until the damaged parts are fixed/replaced.
These instructions are provided for your safety in order to prevent the risk of Fire, Electric shock or Injury. It is vitally
important that they are read in their entirety before installing your fitting. Please retain for future reference.
MADE IN BRITAIN
ORIGINALBTC.COM
[phone]
UNIT 21 / 22 AVENUE ONE, STATION LANE, WITNEY, OX28 4XZ, ENGLAND
L
N
Live
KEY
Neutral
Earth
L =
N =
=
*Mains
Supply
Fitting
*After 2004, wiring installation colours changed:
LIVE Brown replaces Red
EARTH Green/Yellow sleeving
NEUTRAL Blue replaces Black
BROWN
GRN/YEL
BLUE
BROWN
GRN/YEL
BLUE
Established in 1990, Original BTC manufactures relaxed, familiar lighting for traditional and contemporary homes.
All products are hand-assembled in Oxford from high quality components, produced in the UK.
Cleaning and Maintenance
Metal finishes should only be cleaned with a soft, dry cloth. Do not use polishes or abrasives. Glass can be cleaned by hand,
using a soft damp cloth with a diluted mild detergent (nonabrasive) or suitable glass cleaner if necessary. Switch off power to
the fitting before cleaning. Spare parts are available for this product, please contact us on the details below.
Miniature Exterior Bulkhead Fitting
DP8034
DP8035 DP8037 DP8038

Miniature Exterior Bulkhead 230V ac 50Hz Installation DiagramIP65
G9 VERSION
Remove bezel and mark and drill holes for installation, following points 5 and 6 overleaf. This
product is supplied unwired and should be connected directly to the mains supply. Remove the tip of
the gland and wire, following points 8 to 10 overleaf.
GX53 VERSION
Remove bezel and mark and drill holes for installation, following points 5 and 6 overleaf. This
product is supplied wired and should be connected to the mains though the supplied connector,
following points 8 to 10 overleaf.
When installing the light in a damp or exterior location we recommend sealing the backplate against
the fixing surface using a thin bead of silicone to protect the fitting against moisture ingress.
DP8034/DP8035/DP8037/DP8038/G9
Miniature Exterior Bulkhead Fitting
DP8034/DP8035/DP8037/DP8038/GX53
Miniature Exterior Bulkhead Fitting
LAMP GUIDANCE
TYPE* WATTAGE** BASEPRODUCT SHAPE
* Warm white (2700k) low energy lamps recommended.
** Wattage value provided as a guide to suitable lamps. Lower wattage than stated may be used.
Installation and Assembly Instructions
PLEASE READ THE INSTRUCTIONS ON THE REVERSE BEFORE YOU BEGIN INSTALLING YOUR LIGHT
8034/8035
8037/8038
G9
8034/8035
8037/8038
GX53
Contents
1 - Socket screws
2 - Bezel
3 - Glass
4 - Gasket
5 - Backplate
6 - 3 x Insulating sleeves
7 - Allen key
8 - 2 x Fixing screws
9 - 2 x Rawl plugs
10 - 2 x Washers
11 - Connector (GX53 only)
1 2
3 4 5
G9 CAPSULE


HALOGEN
LED
40W MAX
4W
GX53


CFL
LED
7W
7W
A
A FIXING SCREWS
B CONNECTOR*
C MAINS SUPPLY
*GX53 ONLY
G9 GX53
Fixing holes
GX53 VERSION - CONNECT TO MAINS SUPPLY
THROUGH IP44 CONNECTOR BLOCK
G9 VERSION - WIRE DIRECTLY INTO MAINS SUPPLY
Gland Fixing holes Gland
6
7
89 10
cut
L
N
Live
KEY
Neutral
Earth
L =
N =
=
*Mains
Supply
Fitting
*After 2004, wiring installation colours changed:
LIVE Brown replaces Red
EARTH Green/Yellow sleeving
NEUTRAL Blue replaces Black
BROWN
GRN/YEL
BLUE
BROWN
GRN/YEL
BLUE
B
C
C
11
DISC