Original BTC Davey Lighting 7684 User manual

Exterior Bracket Light
Instruction Manual
7684 / 7685
Safety & Installation Instructions
1. If you are in any doubt consult a qualified electrician as to the installation of the fitting. Install in accordance with current
IEE wiring regulations. It is recommended that this fitting is installed by a qualified electrician.
2. Ensure that the electrical supply is OFF. Disconnect the electrical supply at the fuse-board.
3. If removing an existing fitting first, note all wiring connections: record which of the house wires is connected to the live,
neutral and earth terminals.
4. Carefully identify where the supply cable is (and check there are no other cables in the area) to avoid damage to concealed
wiring during installation.
5. Position the light where desired ensuring that there is suitable support adjacent to where you will connect to the house
supply and mark position of fixing holes, before drilling appropriate holes as below.
6. a. Brick or masonry: Drill holes into which the wall plugs tightly fit, then insert wall plugs.
b. Wood: No hole necessary (unless small pilot hole required), screws can be screwed directly into the timber.
c. Plaster/Cavity: Special cavity wall fittings are required, rather than provided fixings. These are widely available from
good hardware or DIY store and should come with their own instructions that must be followed. It may be easier to
relocate the fitting so that you screw directly into a timber joist or beam.
7. Support the fitting so that no strain is applied to the wiring when making the electrical connections. If necessary get a
colleague to help.
8. Electrical connection: this light fitting must be earthed. Make connections following the diagram below using the terminal
block provided. A small flat-head screwdriver is required.
9. To maintain the IP rating of this fitting, you must ensure that the electrical connection has suitable protection from water
ingress, housing the connection in an IP rated junction box or sealing the backplate with silicone.
10. Ensure that all electrical connections are tight, with no loose strands of wire left out of the connectors. Ensure the lid of the
connector is closed securely and that no wires are trapped behind or within the fitting. Complete the installation by
screwing the fitting to the mounting surface.
11. Fit the correct type and wattage of lamp (or less). Be careful not to overtighten the lamp.
12. Switch on at the fuse-board. Your light fitting is now ready for use.
Other Important Information
Switch off at mains before changing lamp(s). Never fit a lamp of greater wattage than recommended. Ensure children do not
play with the light fitting. Dispose of old lamps carefully. Never leave a fitting without a lamp in position (or someone can
accidently touch the contacts). Adjust fitting only when power to the fitting is off and has been left to cool. If the electrical flex
or electrical components become damaged at any point, power to the fitting should be disconnected immediately and not
operated until the damaged parts are fixed/replaced.
These instructions are provided for your safety in order to prevent the risk of Fire, Electric shock or Injury. It is vitally
important that they are read in their entirety before installing your fitting. Please retain for future reference.
MADE IN BRITAIN
ORIGINALBTC.COM
[phone]
UNIT 21 / 22 AVENUE ONE, STATION LANE, WITNEY, OX28 4XZ, ENGLAND
Exterior Bracket Light
DP7685
Exterior Bracket Light
DP7684
Exterior Bracket Light,
Canted Arm
DP7685
Exterior Bracket Light,
Canted Arm
DP7684
L
N
Live
KEY
Neutral
Earth
L =
N =
=
*Mains
Supply
Fitting
*After 2004, wiring installation colours changed:
LIVE Brown replaces Red
EARTH Green/Yellow sleeving
NEUTRAL Blue replaces Black
BROWN
GRN/YEL
BLUE
BROWN
GRN/YEL
BLUE
Established in 1990, Original BTC manufactures relaxed, familiar lighting for traditional and contemporary homes.
All products are hand-assembled in Oxford from high quality components, produced in the UK.
Cleaning and Maintenance
Metal finishes should only be cleaned with a soft, dry cloth. Do not use polishes or abrasives. Glass can be cleaned by hand,
using a soft damp cloth with a diluted mild detergent (nonabrasive) or sutiable glass cleaner if necessary. Switch off power to
the fitting before cleaning. Spare parts are available for this product, please contact us on the details below.
v1.2-04.19

Exterior Bracket Light 7684 / 7685
PLEASE READ THE INSTRUCTIONS ON THE REVERSE BEFORE YOU BEGIN INSTALLING YOUR LIGHT
230V ac 50Hz Installation DiagramIP54
An exterior bracket light with a heavy cast reflector, which is retained by brass wing nuts and bolts
for easier access to the lamp. Available in either galvanised cast iron or sandblasted bronze finish
and with a canted or righ angle arm. Glass is clear or frosted.
DP7684 Exterior Bracket Light
DP7685 Exterior Bracket Light
DP7684/C Exterior Bracket Light Canted Arm
DP7685/C Exterior Bracket Light Canted Arm
Contents
1 - Backplate/Arm/Pan assembly
2 - Wingnut*
3 - Wide Gasket
4 - Narrow Gasket
5 - Ring (7684)/Reflector (7485)
and swing bolt
6 - Well Glass
7 - 2 x Fixing screws
8 - 2 x Rawl plugs
9 - Connector
Required for Installation
-Screwdriver, flat-head
- Small screwdriver, flat-head
- Drill (if holes are required)
A Fixing Screw B Connector Block C Main Supply
Key
Installation and Assembly Instructions
1
2
3
4
5
6
Wide gasket
Narrow gasket
*Wingnuts secure pan/reflector and well glass in place.
Loosen to allow removal of the pan/reflector and glass
when re-lamping.
B
C
A
Install light as described overleaf and then assemble the rest of the light, following the
diagram on the opposite page.
- Ensure the wide gasket (the one with the smaller inner hole) fits into the top of the pan (next to lampholder).
- Ensure the narrow gasket is positioned under the lip of the glass (and above reflector/ring).
- Having inserted a light bulb, position the glass in the pan and then secure in place by attaching the ring/reflector
to the pan by fitting the wing nuts to the swing bolts through the pan. DO NOT OVER TIGHTEN.
If the light is to be installed in an exterior location, it is advised that a thin bead of sealant is applied around the
back plate to prevent water damage.
E27 GLS BALL
LAMP GUIDANCE
TYPE* WATTAGE** BASE SHAPE




INCANDESCENT
CFL
ECO-HALOGEN
LED
60W MAX
15W
28W
12W
* Warm white (2700k) low energy lamps recommended.
** Wattage value provided as a guide to suitable lamps. Lower wattage than stated may be used.
9
8
7