Original BTC Davey Lighting 8504 User manual

Wall/Ceiling Light
Instruction Manual
v1.1-04.19 8504/8519
Safety & Installation Instructions
1. If you are in any doubt consult a qualified electrician as to the installation of the fitting. Install in accordance with current
IEE wiring regulations. It is recommended that this fitting is installed by a qualified electrician.
2. Ensure that the electrical supply is OFF. Disconnect the electrical supply at the fuse-board.
3. If removing an existing fitting first, note all wiring connections: record which of the house wires is connected to the live,
neutral and earth terminals.
4. Carefully identify where the supply cable is (and check there are no other cables in the area) to avoid damage to concealed
wiring during installation.
5. Position the light where desired ensuring that there is suitable support adjacent to where you will connect to the house
supply and mark position of fixing holes, before drilling appropriate holes as below.
6. a. Brick or masonry: Drill holes into which the wall plugs tightly fit, then insert wall plugs.
b. Wood: No hole necessary (unless small pilot hole required), screws can be screwed directly into the timber.
c. Plaster/Cavity: Special cavity wall fittings are required, rather than provided fixings. These are widely available from
good hardware or DIY store and should come with their own instructions that must be followed. It may be easier to
relocate the fitting so that you screw directly into a timber joist or beam.
7. Support the fitting so that no strain is applied to the wiring when making the electrical connections. If necessary get a
colleague to help.
8. Electrical connection: this light fitting must be earthed. Make connections following the diagram below using the terminal
block provided. A small flat-head screwdriver is required.
9. Double check all the connections are secure and that no loose strands of wire are left out of the connector.
10. Check that no wires are trapped behind or within the fitting and complete the installation, referring to the Installation
diagram inside.
11. Fit the correct type and wattage of lamp (or less). Be careful not to overtighten the lamp.
12. Switch on at the fuse-board. Your light fitting is now ready for use.
Other Important Information
Switch off at mains before changing lamp(s). Never fit a lamp of greater wattage than recommended. Ensure children do not
play with the light fitting. Dispose of old lamps carefully. Never leave a fitting without a lamp in position (or someone can
accidently touch the contacts). Adjust fitting only when power to the fitting is off and has been left to cool. If the electrical flex
or electrical components become damaged at any point, power to the fitting should be disconnected immediately and not
operated until the damaged parts are fixed/replaced.
These instructions are provided for your safety in order to prevent the risk of Fire, Electric shock or Injury. It is vitally
important that they are read in their entirety before installing your fitting. Please retain for future reference.
MADE IN BRITAIN
ORIGINALBTC.COM
[phone]
UNIT 21 / 22 AVENUE ONE, STATION LANE, WITNEY, OX28 4XZ, ENGLAND
L
N
Live
KEY
Neutral
Earth
L =
N =
=
*Mains
Supply
Fitting
*After 2004, wiring installation colours changed:
LIVE Brown replaces Red
EARTH Green/Yellow sleeving
NEUTRAL Blue replaces Black
BROWN
GRN/YEL
BLUE
BROWN
GRN/YEL
BLUE
Established in 1990, Original BTC manufactures relaxed, familiar lighting for traditional and contemporary homes.
All products are hand-assembled in Oxford from high quality components, produced in the UK.
Cleaning and Maintenance
Metal finishes should only be cleaned with a soft, dry cloth. Do not use polishes or abrasives. Glass can be cleaned by hand,
using a soft damp cloth with a diluted mild detergent (nonabrasive) or suitable glass cleaner if necessary. Switch off power to
the fitting before cleaning. Spare parts are available for this product, please contact us on the details below.
Wall/Ceiling Light
8504
Wall/Ceiling Light
8519

Wall/Ceiling Light 8504/8519
PLEASE READ THE INSTRUCTIONS ON THE REVERSE BEFORE YOU BEGIN INSTALLING YOUR LIGHT
230V ac 50Hz
Installation Diagram
IP65
8504 Wall/Ceiling Light 8519 Wall/Ceiling Light
Contents
1 - Screws
2 - Bezel/Eyelid shield
3 - Glass/Gasket
4 - Base
5 - Insulating washers
6 - Steel washers
7 - Allen Key
Required for Installation
-Screwdriver, flat-head
- Small screwdriver, flat-head
- Drill (if holes are required)
Installation and Assembly Instructions
With roots dating back to the shipyards of nineteenth century London, Davey Lighting combines
industrial design, traditional craftsmanship and the finest raw materials. Authentic and unique,
lights are manufactured in England with the same attention to detail required for their original
industrial purpose. Simplicity of design and choice of finish, including weathered brass and copper,
polished aluminium and galvanised cast iron, make Davey lights equally suited to traditional or
contemporary schemes.
12 3 4
6
7
5
Remove socket screws to remove bezel and glass, then remove lampholder by removing screws (A) to access
connector block to make electrical connection. Remove the tip of the gland,
cutting (using wire cutters or scissors) across horizontally to allow supply cable
to be inserted, then follow instructions overleaf to install fitting.
Having completed installation, screw lampholder back in then replace bezel and glass, securing firmly in place with
socket screws, creating a tight seal. DO NOT OVERTIGHTEN.
cut
CB D E
A
FG
H
A
B
C
D
E
Lampholder Fixing Screws
GX53 Lampholder
Fixing Holes
Connector Block
Cable Entry Gland
F
G
H
Fixing Screws*
Rawl plug*
Main Supply*
Key
*Not supplied




INCANDESCENT
CFL
HALOGEN
LED
n/a
7W
n/a
7W
GX53 DISC
LAMP GUIDANCE
TYPE* WATTAGE** BASE SHAPE
* Warm white (2700k) low energy lamps recommended- supplied with 5.5W LED GU10.
** Wattage value provided as a guide to suitable lamps. Lower wattage than stated may be used.