Orion ORCH-077S User manual

http://www.orion.ua
I
IN NS ST TU UC CT TI IO ON NM MA AN NU UA AL L
CONVECTOR HEATER
Model: ORCH-077S
ENGLISH GB
220V 50Hz 1000W/2000W

http://www.orion.ua10
DEAR CUSTOMERS!
MANY THANKS FOR BUYING ORION CONVECTOR HEATER!
We really believe you will get the greatest pleasure from using this device for the years!
Please, read the user’s guide in detail before first using of this ceramic fan heater.
1. Read all instructions before using Heater.
2. Use this Heater only as described in this manual. Any other use not recommended by the
manufacturer may cause fire, electrical shock, or injury to person.
3. Make certain that the power source conforms to the electrical requirements of the Heater.
4. Extreme caution is necessary when any Heater is used by or near children or invalids and whenever
the Heater is left operating unattended.
5. Where possible, avoid the use of extension cords because the extension cord may overheat and
cause a risk of fire.
6. Do not operate any Heater with a damaged cord or plug or after the Heater malfunctions, has been
dropped or damaged in any manner. Return Heater to authorized service facility for examination,
electrical or mechanical adjustment or repair.
7. Unplug power cord before servicing or moving the Heater. Always unplug Heater when not in use.
8. Do not insert or allow fingers or foreign objects to enter any ventilation or exhaust opening as it may
cause an electrical shock or fire, or damage the Heater .Do not block or tamper with the heater in any
manner while it is in operation.
9. To prevent a possible fire, not block air intakes or exhaust in any manner. Do not place on soft
surfaces, like a bed, where opening s may become blocked.
10. Always place the Heater on a stable, flat, level surface when operating, to avoid the chance of the
heater overturning. Locate the power cord so that Heater or other objects are not resting on it, Do not
run Power Cord under carpeting .Do not cover Power Cord with throw rugs runners, or the like.
Arrange Power Cord away from room traffic and where it will not be tripped over.
11. This Heater is hot when in use. To avoid burns, do not let skin touch hot surfaces. Always use handle
when moving this heater, Keep combustible materials, such as furniture, pillows, bedding, papers,
clothes and curtains at least 50cm from the Heater.
12. A Heater has hot and arcing or sparking parts inside. It must NOT be in potentially dangerous
locations such as flammable explosive, chemical –laden or wet atmospheres, Heater is intended for
general use only.
13. This Heater is not intended for use in wet or damp location. Never locate a Heater where it may fall
into a bathtub or other water container.
14. Do not use Heater outdoors.
WARNING: To avoid danger of electrical shock, unplug from outlet when not in use and before
cleaning. If the supply cord is damaged, it must be replace by a special cord or assembly
available from the manufacture or its service agent.
SAVE THESE INSTRUCTION FOR FUTURE REFERENCE
GENERAL SAFETY INFORMATION

http://www.orion.ua11
The heater is almost fully assembled apart from the feet which need to be fitted using the 4 screws that
come with the unit. Attach the inner screws 1st and then the 2nd outer screws to ensure unit is perfectly
level.
1. Carefully remove the Heater from the carton.
2. Place the heater on a firm level surface.
3. Set the main power switch to ‘0’. Plug the cord set into a 220V electrical outlet.
4. Turn the main power switch to one of two positions: ‘1’ (1000W) or ‘2’ (2000W).
5. To turn the heater OFF, turn the main power switch to ‘0’ position.
The ‘Thermostat control’ controls the level of heat being emitted but is dependant on the heat
setting. Turn clockwise to increase the level of heat being emitted.
Note : It is normal for the Heater to cycle ON and OFF.
1. A thermal overload protector is built in to prevent overheating.
2. When an overeater temperature is reached, the Heater will be automatically shut off .It can only
resume operation when the user resets the unit.
To Reset Heater:
1. Unplug the Heater and wait 15-20 minutes for the unit to cool down.
2. Then, turn on the unit again and operate normally.
1. Stainless steel safety grille.
2. Chrome carry handles.
3. Power indicator
4. Thermostat control.
5. Power switch.
6. Power cord.
7. Stable base.
PARTS NAME
OPERATION
THERMOSTAT INSTRUCTIONS
SAFETY FEATURES
1
2
4
3
5
6
7
ASSEMBLING THE HEATER

http://www.orion.ua12
WARNING: ALWAYS UNPLUG THE CORD BEFORE MOVING OR SERVICING.
CLEANING : IMPORTANT! DO NOT IMMERSE HEATER IN WATER!
Clean the Heater grille with the vacuum brush attachment on your vacuum cleaner. This will
remove lint and dirt from the inside of the heater .DO NOT ATTEMPTS TO TAKE APART
HEATER. DO NOT REMOVE GRILLE. Clean the body of the heater with a soft cloth.
CAUTION: Do not use gasoline benzene, thinner, harsh cleaners, etc. as they will damage
the Heater . NEVER use ALCOHOL OR SOLVEVTS
STORAGE: Store the Heater with these instructions in the original carton in a cool, dry place.
Model: ORION ORCH-077S
Power supply: 220V~50Hz
Power: 1000W/2000W
Working area: 20~23 m2
Colour: Silver
Gross weight: 5,2kg
Net weight: 4,2kg
Size: 670x180x555mm
Extra information on ORION company web-site www.orion.ua
We take your opinion and offers by E-mail [e-mail]
MAINTENANCE
TECHNICAL SPECIFICATIONS