ORTNER ABS Combustion Control V2.2 User manual

Operating ManualOperating Manual
LED
WLAN
DISPLAY
of the ORTNER Combustion Control V2.2
ORTNER control installed on:
Serial number

ORTNER Inside: ORTNER Speicherecke 09-70/40/38, Design: black

Page 3
Tabl of content
One control, three display options ���������������������������������������������������������������������������������4
General function ���������������������������������������������������������������������������������������������������������5
Important information �������������������������������������������������������������������������������������������������6
Initial start-up�������������������������������������������������������������������������������������������������������������6
LED variant ����������������������������������������������������������������������������������������������������������������8
Visualization of the combustion phases with LED ����������������������������������������������������������8
Combustion phases and colour description ��������������������������������������������������������������������8
Display variant �������������������������������������������������������������������������������������������������������� 10
Visualization of the combustion phases with glass display �������������������������������������������� 10
Indications on the display of each heating phase���������������������������������������������������������� 10
WLAN variant ����������������������������������������������������������������������������������������������������������� 12
Visualization of the combustion phases with LED �������������������������������������������������������� 12
Visualization of the combustion phases via the WLAN module ������������������������������������� 12
Installation of the WLAN module with mobile devices�������������������������������������������������� 13
Integration in an existing personal network ����������������������������������������������������������������� 14
Integration has failed� Now what?������������������������������������������������������������������������������� 16
Error messages and their correction ���������������������������������������������������������������������������� 18
Heating up errors ������������������������������������������������������������������������������������������������������ 18
Defective sensor��������������������������������������������������������������������������������������������������������� 18
Temperature at rest���������������������������������������������������������������������������������������������������� 19
No power supply �������������������������������������������������������������������������������������������������������20
Door open, although the door is closed ������������������������������������������������������������������������20
Door closed, although the door is open ������������������������������������������������������������������������ 21

On contro uni, thre displa option
The ORTNER Combustion control (ABS) offers 3 different options:
• ORTNER control with LED display
• ORTNER control with LED display and WLAN
• ORTNER control with display (black or white)
The ORTNER combustion control. Simple and elegant. Fig.1: LED variant, Fig.2: Display black, Fig.3: WLAN view on smartphone
1
23

Page 5
Genera nctio
The heating process of an oven system is divided into various burning phases / stages:
1� Standby phase
2� Heating up phase
3� Heating phase
4� Embers phase
5� Standby phase
The ORTNER Combustion control ensures an optimal sequence of the burn-off phases
of the furnace installation� Components such as the sensor and the combustion air ap
ensure accurate control, which not only ensures ease of operation, but also maximum
efciency�
By determining the maximum temperature in the heating phase, and a calculation based
thereon, the optimum shutoff time of the combustion air ap is dened� At this time, the
combustion air damper is automatically closed and the embers phase begins� In this phase,
an open combustion air ap would lead to an undesirable, faster cooling of the furnace
installation�
Thanks to the control, the maximum heat output is achieved, which is delivered to the
room as a soothing heat radiation�
A correct combustion
is critical in order to
enable the pleasant
prolonged heat radiation
in the room.
Shown here: ORTNER
Storage corner 09-70/40/38

Important information
The correct amount of combustion air is a
deciding factor for optimal combustion� It affects
the degree of efciency, i�e� the amount of energy
that can be extracted from the wood� Furthermore,
it ensures an optimal air volume for a clean burn,
clean observation windows and an environmentally-
friendly combustion� When the optimal closing time is
reached, the storage of the masonry heater is not
cooled by the supply of fresh air and as a result
does not reduce the storage duration� The ORTNER
combustion control safeguards the optimal energy yield
with a maximum degree of safety�
In the event of a power failure, the
combustion air register of the control unit
is opened automatically�
Initial start-up
During the initial start-up and restart as well as
following a power failure, for safety reasons, the
control always starts in the heating up phase and the
combustion air register remains open� Therefore,
in the event of a power failure during the heating
process, the fuel is burnt safely�
In the event that the temperature is
>50°C - <250°C following a power failure,
the control remains in the heating up phase�
When the temperature is >250°C, the control switches
to the heating phase�
When the temperature remains below a temperature
of 50°C during a waiting period of 60minutes,
the control will return to the standby mode� Only then
will the combustion air register close again�

Page 7
ORTNER Inside: ORTNER Grundofen 11-42/59, Appearance: Traditional tile-green

LED varian
The LED variant is the most basic of the ORTNER control range. This visualization of
the ABS displays the different combustion levels in the most simplest manner.
Visualization of the combustion phases with LED
Combustion phases and colour description
The control is in the standby mode
Standby state:
• The stove is not heated
• The temperature in the combustion chamber is <50°C
• The combustion air register is closed
The door(s) are opened for heating up
Door open:
• The door is open for the insertion the fuel
• The combustion air register opens
The masonry heater is in the heating up phase:
Heating up state:
• Is activated with the closure of the door
• The combustion air register is open
• The temperature in the combustion chamber is <250°C
Green
Standby mode
Blue
Door open
Orange
Heating up Red
Heating
<600°C
Purple
Ember phase
Light purple
Heating
>600°C
Red
Heating
<600°C

Page 9
The masonry heater switches to the heating phase:
Heating state
• Is activated from a temperature of >250°C
• The combustion air register is open
• The maximum temperature is stored
• Determination of the optimal transition temperature to embers
The masonry heater switches to the heating phase >600°C:
Heating state
• The temperature increases to >600°C
• The combustion air register is open
• The maximum temperature is stored
• Determination of the optimal transition temperature to embers
The masonry heater switches to the heating phase >600°C:
Heating state
• The temperature drops to <600°C
• The combustion air register is open
The masonry heater switches to the embers or storage phase:
Embers state:
• Is activated when the optimal transition temperature is reached
• The combustion air register closes
• The embers phase begins
• Optimal heat storage is enabled
Renewed refuelling with wood in order to increase the storage duration
Door open:
• In the event that wood should be added again for combustion, this
should be performed during the embers phase� In this case, the combustion
starts again� When relling on the still fresh embers, only add half the wood
amount�

Indications on the display of each heating phase
Status of the standby mode:
• The stove is not heated
• The temperature in the combustion chamber is <40°C
• The combustion air register is closed
• The display is dimmed
Line 2 on the display: Status: Standby mode
Displa varian
All important data is presented on the display during the combustion� In this manner,
you can continuously see the temperature and the status of the heating process� When the
control switches into the embers phase, the display will dim� Only when a new combustion
is begun will the display light up again brightly and all status messages will be displayed�
Visualization of the combustion phases with glass display
Current temperature
Current
combustion phase &
status messages on
temperature 2
(if present)

Page 11
Door open for heating up:
• The stove door is opened for heating up
• The heating up phase begins with the closing of
the door
• The combustion air register opens
Line 2 on the display (= continuous text): Status:
Door open – register open – (TEMP2 = 27°C)
Heating up state:
• Is activated with the closure of the door
• The combustion air register is open
• The temperature in the combustion chamber is
>50°C-<250°C
Line 2 on the display (= continuous text):
Status: Anheizen – Tür geschlossen – Klappe offen –
Heating time= 2min – (TEMP2= 27°C)
Heating state
• Wird ab einer Temperatur >250°C aktiviert
• The combustion air register is open
• The maximum temperature is stored
• Determination of the optimal transition
temperature to embers state
Line 2 on the display (= continuous text):
Status: Heating – door closed – register open –
heating time = 25min – (TEMP2 = 230°C)
Embers state:
• Is activated when the optimal transition
temperature is reached
• The combustion air register closes
• The display is dimmed
• The heating time stops and the embers phase
begins
• Optimal heat storage is enabled
Line 2 on the display (= continuous text):
Status: Embers – door closed – register closed –
heating time = 100min – (TEMP2 = 230°C)

WLAN varian
Easily monitor the combustion of your masonry heater via a smartphone, tablet
or PC
In combination with the LED display, the WLAN module provides you with the option
to also visualize the current status of the combustion on mobile devices�
Visualization of the combustion phases with LED
Visualization of the combustion phases via the WLAN module
Green
Standby mode
Blue
Door open
Orange
Heating up Red
Heating
<600°C
Purple
Ember phase
Light purple
Heating
>600°C
Red
Heating
<600°C
Status of the door
Current temperature 1
Current combustion
phase
Heating time
Status of the combustion
air register
Temperature 2 optional

Page 13
Installation of the WLAN module with mobile devices
1� Disconnect the control from power
2� Set the switch on the WLAN module to the LEFT POSITION
3� Switch the control on
4� Activate your WLAN on your telephone or tablet and connect with ORTNER-… (e�g�
ORTNER-lower)
5� Launch your web browser (Internet) and enter http://1�2�3�4 in the search bar
Congratulations, you have successfully connected with the WLAN module and can now
access all data online.
The ORTNER combustion control. Using the WLAN module, you can also receive
all data on mobile devices. The combination with the LED display
also serves as an additional variant in order to be able to see the current
combustion phase without the use of a smartphone, tablet or PC.

INTEGRATION IN AN EXISTING PERSONAL WLAN NETWORK
In this example, Internet Explorer and Windows 7 are used; the
procedure is similar or identical to that used with other operating systems and web
browsers.
1� Switch off the control (disconnect from power)
2� Set the switch on the WLAN module to the centre position and connect the module to
the control
3� Switch the control on
4� Move the switch on the WLAN module to the left after at least 5seconds and return
it to the centre position after approx� 1second�
5� Using a device with wireless connectivity (notebook, smartphone, tablet, etc�) search
for the “ORTNER” WLAN and connect to this�
6� Open a web browser and enter http://1�2�3�4 in the address bar�

Page 15
7� Press “Refresh List” in order to receive a list with the available networks�
8� Select the desired network and enter the password of your personal network in “Pass
phrase”� The settings are saved by pressing “Save Conguration”�
9� Switch the control off and back on after approx� 5seconds�

Try to locate teh module‘s IP assress, under the following possibilities:
1� Windows
Use the SoftPerfect Network Scanner application
http://www�softperfect�com/download/freeware/netscan�zip
2� First press “Auto Detect IP Range” and then “Start Scanning”
3� Search the MAC address that is noted on the module’s mounting,
e�g� 00-06-66-81-05-3F

Page 17
4� Enter the corresponding IP address in the web browser http://<IP-Adresse>/�
In this example 192�168�1�116 http://192�168�1�116/�
5� Android and iPhone
The free app “Fing” is available for Android and iPhone:
https://play�google�com/store/apps/details?id=com�overlook�android�ng&hl=de
https://itunes�apple�com/at/app/ng-network-scanner/id430921107?mt=8
6� Search the MAC address that is noted on the module’s mounting,
e�g� 00-06-66-81-05-3F, the IP address is noted immediately above it� Enter this in
your web browser�
If you have located the IP address of the module, the page can be added as a quick access
to the home or start screen�
Instructions for Android:
1� Open the page, using the IP address, in the Chrome browser�
2� Touch the three small dots in the upper right corner to open the menu�
3� Select „Add to Home Screen,“ whereby the name can still be changed
4� The icon with the corresponding website link will then be saved on your home screen�
Instructions for iPhone:
1� Enter the IP address in the Safari browser�
2� Touch the share icon
3� Touch „To Home Screen“
4� Touch Add, whereby the name can still be changed
5� Now the link has been created

Error message an their correctio
Heating up errors
LED lit and ashing
Heating up errors
Display text of the glass display
TEMP1 230°C
Heating error – Door closed – Heating error – Register open – Heating error – Heating time
= 61min - Heating error – TEMP2 = 80°C
Possible cause
• The temperature is >50°C, it does not increase above 250°C within 60 min�
• This means that the re fails to start burning properly (e�g� the wood is too damp)�
• An insufcient amount of wood was inserted or replenished�
Correction
Following a power failure or after each opening and closing of the door, the control
switches into the heating up phase and the error message is acknowledged� The
combustion phases are run through again� However, when the temperature drops below
50°C during this error message, it is also acknowledged and the control switches into the
rest phase�

Page 19
Defective sensor
LED ashing
Sensor error
Display text of the glass display
Sensor error – Door closed – Sensor error – Register open – Sensor error – Heating time –
100min – Sensor error – (Temp2 = 29°C)
Possible cause
• The contact of the temperature sensor is interrupted�
• Temperature sensor is defective�
Correction
Check the contact connection of the cables on the compression tting of the control� When
the tting of the cable is secure and has been connected correctly, then the thermocouple
must be replaced� When thermocouple 2 is defective, then it is no longer displayed� Please
contact your stove tter in order to have the thermocouple replaced�
Temperature at rest
LED lit and ashing
Temperature at rest
Display text of the glass display
TEMP1 52°C
Temperature increase – Door closed – Temperature increase – Register open –
Temperature increase – (Temp2 = 38°C)
Possible cause
Temperature increase in the combustion chamber (>50°C) by the self-ignition
of the inserted wood amount as a result of still present residual embers�
Correction
Should this error message occur, the control will begin the heating up phase, starting
from a temperature >50°C� The combustion air register opens and the wood is burnt
safely� Only add a new amount of wood in the combustion chamber immediately before
ignition in order to prevent the self-ignition by the residual embers�

No power supply
LED not lit
No power supply
The LED is not lit and no motor sounds are audible when the door is opened.
Display text of the glass display
No display text present�
Possible cause
• The LED cable is defective
• The compression tting on the LED is not secured correctly
• Short-circuit
• Power failure
Correction
First check the compression ttings of the LED cable on the control� When the
compression tting of the LED on the control is secured correctly, the cable or the LED
is defective� Please inform your stove tter in order to have the LED replaced� Measures
for improvement and avoidance should be taken in order to prevent the damage from
occurring again� Please consult us�
Door open, although the door is closed
LED lit continuously
Door open
Display text of the glass display
TE MP1 45°C
Door open – Register open – (Temp2 = 30°C) – Door open – Register open
Possible causes
• No earth contact on the door contact or door sensor�
• Screwed connection on the control is loose�
• Cable connected incorrectly�
Table of contents
Popular Control System manuals by other brands

BRULA
BRULA BRULA NEO Installation and service instructions

Universal Remote Control
Universal Remote Control MX-3000 brochure

Julabo
Julabo Presto LH 45 operating manual

Altronic
Altronic DE-4000 installation instructions

IDTECK
IDTECK iMDC-MAIN user manual

White Rodgers
White Rodgers 50E47-843 installation instructions