ORTOLED QB-EVO ORTOLED-89-QBEVO-150W User manual

ORTOLED QB-EVO LED GROW LIGHT
INSTRUCTION MANUAL

Product and recommended application
Model no.
ORTOLED-89-QBEVO-150W
Dimension
358*357*40MM
Power
150W
Application
Indoor growing
Recom. Height
40-70CM
Model no.
ORTOLED-90-QBEVO-240W
Dimension
500*500*43MM
Power
240W
Application
Indoor growing
Recom. Height
40-70CM
Model no.
ORTOLED-90-QBEVO-240W
Dimension
500*620*48MM
Power
320W
Application
Indoor growing
Recom. Height
40-70CM
1. Picture of products

2. Delivery contents
- 1 x LED Grow Light
- 1 x Power Cable
- 1 x 3m long RJ11 Signal Cable
- 2 x Adjustable Hanging Kits + 2 x Un-adjustable Hanging Kits
Please keep the instruction manual and desist from throwing it away. It might come in handy with
future troubleshooting.
3. Products Structure
Power input
SMD leds

Model
ORTOLED-89-QBEVO-150W ORTOLED-90-QBEVO-240W ORTOLED-91-QBEVO-320W
Power Consumption
150W
240W
320W
Product Size
358*357*40mm
500*500*43mm
500*620*48mm
N.W/G.W
1.87KG/2.79KG
2.6KG/4.5KG
3.8KG/5.6KG
Packing size
410*90*445mm
550*90*580mm
550*95*710mm
Light Source
Samsung lm201b 3000K 5000K LEDs + Honglitronic SMD3535 3w 660nm
450nm LEDs
PPF Efficacy
2.7umol/J
Spectrum
Full Spectrum for Veg Flowering
AC Input
AC100-277V 50/60Hz
Power Supply
Sosen LED Driver
Power Factor
＞0.90
Control
Master and Slave Daisy Control
/ Supports any 0-10V external controller
Light Distribution
120 Degree
Working Tempt.
-20℃~40 ℃
Warranty
3 Years
4. Product Datasheet
Master/Slave switch
Signal input
Signal output
Dimming Knob
Driver
4.1 Product Specification

4.2 Spectrum
Control Method:
1. Single led fixture:
Switch to master button, use the dimming knob to dimming.
Notice: If switch to slave button, the dimming knob will not functional.
Signal
5. Control

2. Multi-led fixture:
Step one: Choose one light as master, and the other lights as slaves
Step two: Use the dimming knob to dimming, all the slaves will be controlled by master.
3．Existing 0-10V Controller to control the fixtures:
Step one: use RJ12 cable to connect the controller and fixture
Step two: switch all the fixture to slave (max. 20pcs fixtures)
Step three: use the 0-10V controller to control the fixtures.
•Transportation
Improper transportation may harm or can even cause damage to LED lamp and power housing box). In case
of obvious damage or incomplete scope of supply, please refer to your vendor and Haulage company
immediately.
•Unboxing
Please handle and unbox the LED lamp with care! Check the delivery contents for completeness first. A
detailed list of the product range is contained on the inner cover in this manual.
6. Preparation

Through transport or due to a long storage time, the LED-modules might get a little polluted.
Therefore we recommend to clean the modules before each use with a dry and soft tissue.
7.1 Safety measures & precaution
Warning! This LED fixture is powered with electricity (AC100-250V)! To prevent injury, we ask you to
desist from improper use!
•• Never open the case of the device! Health hazards await the consumer and the warranty of the device
expires.
7.2 Putting into service
Operate the LED fixture only horizontally, while hanging or slightly angled (approx. about 20°). Deploy the
LED lamp fixture about 30-50cm above the top of the plants;
7.3 Proper use
Do not use the LED fixture vertically or as illumination device upside-down (direct eye contact and long
exposure over time may cause permanent damage to your eyesight!).
We don’t advise you to deploy the device as a room illuminant. It is exclusively designed and developed for
plant breeding, cultivation and hibernation. Please ensure that the LED fixture is being operated out of sight
and out of reach of children and animals to protect their eyes!
7. Operation

www.ortoled.com