OSP Designs 105 User manual

105 / 108
WOOD DESK CHAIR
OPERATING INSTRUCTIONS
LIMITED WarranTy
OSP Designs Warrants, to the original purchaser its products to be free from defects in material and workmanship for a period of 90 days. Defects
and damage from misuse, abuse, negligence, alteration, accident, vandalism, rusting, acts of nature or any other event beyond the control of OSP
Designs is not covered. The warranty does not cover cosmetic damage that may result from normal use. Liability for incidental or consequential
damages is excluded. The user assumes all risk of injury resulting from use of this product. This warranty gives you specific legal rights, and you
may also have other rights which vary from state to state.
To make a warranty claim, contact Customer Service, provide model number, sales receipt and description of the problem. It is the customer’s
responsibility to prepay freight on any components returned to the factory. OSP Designs will pay return freight on components covered under
terms of warranty.
Our quality standards are among the highest in the industry. Sometimes, no matter how hard we try, there are times when hardware is missing.
Our Parts Department will do everything possible to promptly remedy the problem. Contact us via email parts@officestar.net, by Fax
1-909-930-5629, or toll free parts number 1-800-950-7262, Monday through Friday 8:00 a.m. - 5:00 p.m. Pacific Time. OSP Designs P.O. Box
3520 Ontario, California 91761 USA
12
WarnInG
1. Do not use this product unless all screws and bolts are
securely tightened.
2. Check that all screws and bolts are tight every three months or
as needed.
3. Dispose of packing material properly. Do not use plastic cover
as head covering. It may cause suffocation.
4. Do not use this product as a stepladder.
5. Use this product for its intended purpose only.
6. Secure Plastic Caps (13) as they may be a choking hazard for
small children.
7. Intended for residential use only.
FEaTUrES
• HEIGHT ADJUSTMENT
To raise seat remove pressure from seat and lift lever (1). To
lower seat height sit on chair and lift lever (1).
• LOCKING TILT ADJUSTMENT
For individual comfort, this chair has been equipped with an
adjustment that will allow the user to change the tension of
the tilting feature. Turn knob (2) clockwise to increase tension
and counter-clockwise to decrease or ease the tension. To
lock return chair to the upright position and push lever (1) in.
To unlock pull lever (1) out.
NOTE: Be careful not to loosen back tilt adjustment knob
completely.
12
105
108

105 / 108
WOOD DESK CHAIR
ASSEMBLY INSTRUCTIONS
PART QTY
1. Base .......................1
2. Caster ......................5
3. Pneumatic Cylinder ............1
4. Bellows .....................1
5. Seat Plate ...................1
6. Wood Seat ...................1
7. Wood Back ..................1
8. Arms (8L & 8R) ...............2
9. Small Allen Screws ............4
10. Medium Allen Screws .........6
11. Long Allen Screws ...........3
12. Flat Washers ................4
13. Lock Washers ...............4
14. Wood Caps .................9
15. Allen Wrench (not shown) ......1
16. Wooden Cleat ...............1
17. Rubber Mallet (not provided) ....1
1
3
4
5
6
9,13,12
10,14
11,14
DETAIL A
7
8L
8R
10,14
2
© Office Star Products January 2013
10,14
10,14
DETAIL B
17
16
2
1
Remove all parts from carton, separate them by part numbers indicated on the parts list, and verify parts quantities.
STEP 1 Attach Wood Back (7) to Wood Seat (6) using three Long Allen Screws (11). SEE DETAIL A. FULLY TIGHTEN ALL SCREWS USING ALLEN WRENCH (15).
Cover holes in Wood Back (7) using three Wood Caps (14).
STEP 2 Attach Seat Plate (5) to Wood Seat (6), with arrow pointing towards the front of the chair, using four Small Allen Screws (9), four Lock Washers (13) and four
Flat Washers (12). FULLY TIGHTEN ALL SCREWS USING ALLEN WRENCH (15).
STEP 3 Aligh the holes in Arms (8L and 8R) with the holes in the Wood Back (7) and Wood Seat (6), secure Arms (8L & 8R) to Wood Seat (6) using three Medium
Allen Screws (10) for each Arm (8). FULLY TIGHTEN ALL SCREWS USING ALLEN WRENCH (15). Cover holes in Arms (8L & 8R) using three Wood Caps (14)
for each Arm (8).
STEP 4 Insert five Casters (2) into Base (1), push hard until you feel or hear the Caster (2) snap into place. Use Wooden Cleat (16) and Rubber Mallet (17) for easy
installation. SEE DETAIL B. Place Base (1) upright so Casters (2) are on the floor, insert Pneumatic Cylinder (3) into Base (1) and slip Bellows (4) over Pneumatic
Cylinder (3), Place Assembled seat onto Pneumatic Cylinder (3) and apply downward pressure.
ATTENTION : VERIFY THAT ALL SCREWS ARE FULLY TIGHTENDED BEFORE USING CHAIR.