Argos Malibu 719/0487 User manual

MADE IN
BRITAIN
Dimensions
Width - 39cm
Depth - 40cm
Height - 45cm
Malibu - Single Bedside
Assembly Instructions - Please keep for future reference
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Issue 5 - 04/09/12
Important - Please read these instructions fully before starting assembly
Ruler - Use this ruler to help correctly identify the screws
0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
719/0487
719/0494
ALR2443
305/0208
305/0215
305/0239
305/0222
305/0246
Issue 4 - 16/05/12 - New Argos codes added.
Issue 5 - 04/09/12 - Deleted obsolete Argos codes, 630/3134. 630/3086. 630/3220, 630/3103 and 630/3110.

Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: This unit weighs
approximately 13kgs. Please lift
with care.
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
• Parts of the assembly will be
easier with 2 people.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: If there is any
chance of this unit being pulled
over by children etc. it is
recommended that the unit is
secured to a wall using suitable
fixings (not supplied).
• Dispose of all packaging
carefully and responsibly.
Glue Safety - Take care when using glue, please follow the advice below
Skin contact: Remove contami-
nation by washing with soap and
water. This procedure should be
followed prior to aeting and
drinking.
Eye contact: Rinse immediately
with clean water for 15 minutes
and seek medical advice.
If swallowed: Seek medical
advice immediately.
1
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
• From time to time check that
there are no loose screws on
this unit.
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.

Components - Panels
Please check you have all the panels listed below
2
Left Side (D0248A)
(431 x 394mm)
1Right Side (D0249A)
(431 x 394mm)
2Top (D0110A)
(388 x 396mm)
3
Drawer Base (T410)
(297 x 330mm)
8
Plinth (D0112A)
(349 x 92mm)
9
Rail (D0113A)
(349 x 88mm)
10
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Shelf (D0250A)
(349 x 392mm)
11 Back (X724)
(376 x 174mm)
12
Left Drawer Side (W410LH)
(300 x 95mm)
4Right Drawer Side (W410RH)
(300 x 95mm)
5Drawer Back (W410BCK)
(319 x 95mm)
6
Drawer Front (D0111A)
(345 x 157mm)
7

Please check you have all the fittings listed below
Tools required
Glue Safety - Take care when using glue, please follow the advice below
Skin contact: Remove contami-
nation by washing with soap and
water. This procedure should be
followed prior to aeting and
drinking.
Eye contact: Rinse immediately
with clean water for 15 minutes
and seek medical advice.
If swallowed: Seek medical
advice immediately.
3
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
• From time to time check that
there are no loose screws on
this unit.
Components - Fittings If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.
A
Wooden dowel (F22) x 8
B
Metal dowel (F901) x 4
C
Nail holder (F149) x 1
D
Large locking
nut (F900) x 2
E
Small locking
nut (F3) x 2
F
R (F601)
L (F600)
F599
F599
J
Drawer stops (F599) x 2
Runners (F600) x 1 and (F601) x 1
Rule Scissors Hammer Eye protection
(when using a
hammer or drill)
Cross-head
screwdriver
Nail (F51) x 12
Ruler - Use this ruler to help correctly identify the screws
Handle (F631) x 1
I
45mm Screw (F65) x 10
G
A
Wooden dowel (F22) x 8
B
Metal dowel (F901) x 4
C
Nail holder (F149) x 1
D
Large locking
nut (F900) x 2
E
Small locking
nut (F3) x 2
F
G
40mm Screw (F910) x 6
H
25mm Screw (F50) x 1
R (F601)
L (F600)
F599
F599
45mm Screw (F65) x 4
I
J
Drawer stops (F599) x 2
Runners (F600) x 1 and (F601) x 1
Nail (F51) x 12
Handle (F631) x 1
K
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
H
25mm Screw (F50) x 1

Assembly Instructions
4
Prepare drawer front
Screw 2 metal dowels
into the holes shown on
the back of the drawer
front .
Note: Tighten metal
dowels up fully against
the panels.
B
7
F
B
Prepare drawer sides
and back
Insert a small locking
nut into the hole
shown on the left drawer
side and right drawer
side .
Note: Arrow on locking
nut must point towards
hole in edge of panel.
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
B
7
B
F
B
B
I
I
6
5
F
4
5
Assemble drawer
sides and back
Fit the left drawer side
and right drawer side
to the drawer back
using 4 screws .
Note: Line up the small
grooves on the inside of
the drawer assembly.
Fit drawer base
Slide the drawer
base along the small
groove of the drawer
sides and into the
small groove of the
drawer back .
I
4
5
6
Step 3
Assemble drawers x 3
a: Slide the drawer
base along the
grooves of the drawer
sides and into the
groove of the drawer
back .
b: Turn the drawer
assembly over and push
onto the back of the
drawer front .
Note: Turn locking
nuts clockwise to
secure panels - more
than 1/2 a turn.
8
8
4 5
6
4
5
6
4
F
4
I
I
5
F
Step 1
Step 2
Step 3
Step 4
Small
groove

Assembly Instructions
5
a:
b:
8
Step 2
Assemble drawers x 3
a: Place drawer base
into the narrow slot on
the drawer wrap .
Fold wrap around the
base.
b: Turn drawer wrap
assembly over and push
onto the back of the
drawer front .
Note: Turn locking
nuts clockwise to
secure panels - more
than 1/2 a turn.
8
5
4
F
4
5
4
5
5
B
B
F
Attach drawer front
Turn the drawer
assembly over and push
onto the back of the
drawer front .
Note: Turn locking
nuts clockwise to
secure panels - more
than 1/2 a turn.
7
F
7
B
B
F
SNAP!
SNAP!
F599
J
J
F599
J
F599
J
F599
J
Attach drawer stops
Carefully break off the 2
drawer stops (F599) from
each pair of the drawer
runners .
Push the drawer stops
fully through the drawer
sides and from
the inside.
J
4 5
4
5
Attach handle
Attach handle to the
drawer front using
screw .
Note: Do not
overtighten the screw.
K
H
K
H
Step 5
Step 6
Step 7

A
Assembly Instructions
Use 2nd hole in from front of
Runner F1004 to fit 1st F73 then
fit other F73 to match other hole.
Rebated Edge
F73
COVERED EDGE
Use 2nd hole in from front of
Runner F1004 to fit 1st F73 then
fit other F73 to match other hole.
F1004
When you insert F900,
make sure the arrow is
pointing towards the hole
in the edge of the panel.
F900
F73
F1004
COVERED EDGE
6
10mm
LF600
a:
b:
Prepare left and right
side
Separate runners .
a: Push fit the left
runner marked ‘L’ into
the holes shown on left
side .
Note: Runners must be
be fitted flat against the
panel. If necessary
gently tap into final
position.
Insert large locking
nut as shown.
Note: Arrow on locking
nut must point towards
hole in edge of panel.
Tap in wooden dowel
as shown.
Note: Wooden dowels
must not stick out from
the edge by more than
10mm or they may
damage other panels.
b: Push fit the right
runner marked ‘R’
into the holes shown on
left side .
Insert large locking
nut as shown.
Tap in wooden dowel
as shown.
1
J
E
A
2
E
A
J
J
JE
A
E
E
A
Finished
front edge J
1
2
R
Finished
front edge F601
J
J
6
Step 8

G
Assembly Instructions
7
Prepare rail and plinth
a: Tap 2 x wooden
dowels into the ends
of the plinth .
b: Tap 4 x wooden
dowels into the ends
of the rail .
A
A
Fit rail and plinth to
the right side
Attach plinth to the
right side using the
dowel already fitted and
secure with screw .
Attach rail to the right
side using the
dowels already fitted.
9
2
G
9
10
Finished front edge
10
2
a:
b: A
A
9
10
A
A
A
A
Finished front edge
10
2
Step 9
Step 10
plain chipboard surface
plain chipboard surface
9

G
G
Assembly Instructions
8
Finish left side
Push the left side
onto the dowels fitted to
the plinth and rail.
Secure the left side with
3 screws .
G
1
G
G
G
1
Fit shelf to the right
side
Attach shelf to the
right side using 2
screws .
11
2
G
L
2
11
Finished front edge
Step 11
Step 12
plain chipboard surface

Assembly Instructions
Use 2nd hole in from front of
Runner F1004 to fit 1st F73 then
fit other F73 to match other hole.
Rebated Edge
F73
COVERED EDGE
Use 2nd hole in from front of
Runner F1004 to fit 1st F73 then
fit other F73 to match other hole.
F1004
When you insert F900,
make sure the arrow is
pointing towards the hole
in the edge of the panel.
F900
F73
F1004
COVERED EDGE
9
Fit back panel
Square up the unit by
making sure that
measurement x:x
equals y:y.
Place the back down
onto the unit, as shown.
a: Use the nail guide
to hold the nails
vertical and at the
correct distance whilst
you nail around the sides
and base of the back .
b: Nail along
the top of the
back (do not
use the nail guide
for this).
Note: Nails should
be spaced about
150mm apart.
Stand the unit up
for the next stage.
D
M
15
15
15
Dyy
Attach top
Push the top onto
the side panels.
Use a screwdriver to
tighten the large locking
nut fitted to each
side.
Note: Turn the large
locking nut as far as it
will go - more than 1/2 a
turn.
3
E
3
B
E
B
Prepare Top
Screw 2 metal dowels
into holes shown on the
underside of the top .
3
B
3
B
Step 13
Step 14
plain chipboard surface