OSP Designs XT30 User manual

XT30
MOBILE FILE
OPERATING INSTRUCTIONS
LIMITED WarranTy
OSP Designs Warrants, to the original purchaser its products to be free from defects in material and workmanship for a period of 90 days. Defects
and damage from misuse, abuse, negligence, alteration, accident, vandalism, rusting, acts of nature or any other event beyond the control of OSP
Designs is not covered. The warranty does not cover cosmetic damage that may result from normal use. Liability for incidental or consequential
damages is excluded. The user assumes all risk of injury resulting from use of this product. This warranty gives you specific legal rights, and you
may also have other rights which vary from state to state.
To make a warranty claim, contact Customer Service, provide model number, sales receipt and description of the problem. It is the customer’s
responsibility to prepay freight on any components returned to the factory. OSP Designs will pay return freight on components covered under
terms of warranty.
Our quality standards are among the highest in the industry. Sometimes, no matter how hard we try, there are times when hardware is missing.
Our Parts Department will do everything possible to promptly remedy the problem. Contact us via email parts@officestar.net, by Fax
1-909-930-5629, or toll free parts number 1-800-950-7262, Monday through Friday 8:00 a.m. - 5:00 p.m. Pacific Time. OSP Designs P.O. Box
3520 Ontario, California 91761 USA
WarnInG
1. Do not use this product unless all screws and bolts are
securely tightened.
2. Check that all screws and bolts are tight every three months or
as needed.
3. Dispose of packing material properly. Do not use plastic cover
as head covering. It may cause suffocation.
4. Do not use this product as a stepladder.
5. Use this product for its intended purpose only.
6. Intended for residential use only

XT30
MOBILE FILE
ASSEMBLY INSTRUCTIONS
© Office Star Products April 2012
IMPORTANT NOTE:
1. Use hand tools only for assembly as power tools
may cause damage
2. Carefully remove any staples used for packaging.
3. Phillips Screwdriver also needed for assembly (not provided)
Remove all parts from carton, separate by part numbers indicated
on parts list, and verify part quantities.
STEP 1 Screw in four Cam Lock Studs (9) into Front Panel (1) and four Cam Locks Studs (9) into Back Panel (2), FULLY TIGHTEN CAM
LOCK STUDS (9), align and attach Side Panels (3) to Back Panel (2) using four Cam Locks (8), insert both Metal Rods (6) into Back Panel (2). Align
and attach Front Panel (1) to Side Panels (3) and secure using four Cam Locks (8). FULLY TIGHTEN CAM LOCKS (8) USING PHILLIPS
SCREWDRIVER (not provided). Attach Handle (12) to Front Panel (1) using two Short Screws (13), FULLY TIGHTEN SHORT SCREWS (13)
USING PHILLIPS SCREWDRIVER (not provided)
STEP 2 Attach Metal Posts (5) to assembly using two Long Screws (10) for each Metal Post (5), FULLY TIGHTEN LONG SCREWS (10)
USING PHILLIPS SCREWDRIVER (not provided)
STEP 3 Attach Bottom Panel (4) to assembly using four Long Screws (10), secure Casters (7) to Bottom Panel (4) using four Wood Screws (11) for each
Caster (7), FULLY TIGHTEN WOOD SCREWS (11) USING PHILLIPS SCREWDRIVER (not provided) AND LONG SCREWS (10)
USING ALLEN WRENCH (16).
STEP 4 Place Hanger Rods (14) onto Metal Rods (6). Cover holes of Cam Lock Studs (9) using eight Plastic Caps (15).
ATTENTION: MAKE SURE ALL SCREWS ARE FULLY TIGHTENED BEFORE USING MOBILE FILER.
STEP 1
STEP 3
2
3
5
4
10
9
13
12
7
6
14
1
PART QTY
1. Front Panel ..................1
2. Back Panel ..................1
3. Side Panel ...................2
4. Bottom Panel .................1
5. Metal Post ...................4
6. Metal Rod ...................2
7. Caster ......................4
11
8STEP 2
PART QTY
8. Cam Lock ...................8
9. Cam Lock Stud ...............8
10. Long Screw ................12
11. Wood Screw ...............16
12. Handle .....................1
13. Short Screw .................2
14. Hanger Rod .................2
15. Plastic Caps .................8
16. Allen Wrench (not shown) ......1
STEP 4
3
10
6
15