Otto REINE 2 OTREINEWE User manual

ASSEMBLY INSTRUCTIONS
ITEM CODE: OTREINEWE
REINE 2 DRAWER DESK
1 Carton
This design and instruction booklet is subject to copyright
www.officeworks.com.au
1/19
For missing hardware call [phone] or email [email protected]

2/19
NOTE
Please check you have all hardware before assembling.
If you are missing any hardware, please contact Kyvas on [phone]
or email [email protected]
Please ensure you have the item, required hardware part and quantity.
Please retain your receipt as proof of purchase to validate your warranty.
CAUTION
Do not tighten screws before all screws are in the right place.
Do not use this product unless all bolts, screws and knobs are firmly secured.
Check that all bolts, screws and knobs are securely tightened at least
every 4 months. WARNING
If parts are missing, broken, damaged or worn stop using the product until
all repairs are made using manufacturer authorised parts.
Keep children and animals away from the assembly area.
This furniture contains small parts that could cause choking if swallowed.
Keep all plastic wrapping materials away from babies and children to
avoid danger of suffocation.
This item is not for outdoor use – unless stated otherwise.
Failure to follow these warnings could result in serious injury.
DANGER
CHILDREN MUST BE SUPERVISED.
Tools Required
CAUTION:Do not use tools other than those required, as this
your new item. can damage
To view an assembly video, go to https://www.officeworks.com.au/
Search the product by item code or name:
Click on the icon to watch the video.

3/19
Part Overview
1
2
3
4
5
6
8
9
10
11
7
8
9
10
11

23
5 6
7
8
Parts located in Carton - OTREINEWE
4
10
1
9
Part List
X 1
X 1 X 1 X 1
X 1 X 1 X 1
11
X 2 X 2
X 2X 2
4/19

D F
Hardware Pack located in Carton -
OTREINEWE
ABC
Other hardware located in Carton - OTREINEWE
E
Hardware List
For missing hardware, please contact Kyvas on ( 03) 9310 3011 or email [email protected]
X 28pcs X 28pcs X 12pcs
X 24pcs
X 4sets
X 4pcs
M8 x 7 mm
GHI
J
X 4pcs
Nut
X 4pcs
Nut
X 4pcs
Washer
X 1pc
Wrench
K
X 2pcs
Plastic Cap
5/19
L
X 2pcs
Sticker Cover

6/19
E
Assembly
Step 1
X 4sets
(E1) x4
(E2) x4
Separate slider components
(E) x4
1A
1B
1C
Fully extend the sliders by pulling.
Locate tab and press as indicated whilst pulling sliders apart to release sections.
Separated components now become E1 and E2.
This procedure can be viewed in the assembly video.Video details on page 2 of this booklet.

7/19
Step 3
C
A
X 2pcs X 2pcs
A
2
A
A
CC
D
Step 2
X 3pcs X 1pc
E2
D
D
D
E2
2
Front
E2
Front

8/19
Step 5
C
A
X 2pcs X 2pcs
A
3
A
A
C
C
Step 4
D
X 3pcs X 1pc
E2
Front
E2
3
E2
D
D
D
Front

9/19
A
X 2pcs
Step 7
5
A
A
A
Step 6
D
X 6pcs X 2pcs
E2
Front
E2
4
4
D
D
D
D
D
D
E2
E2
Front
Front

10/19
Step 9
Tighten cam locks once panel 2 and 3 are in place.
B
B
X 4pcs
2
3
5
B
B
B
B
Step 8
Tighten cam locks once panel 5 is in place.
B
B
X 2pcs
4
B
B
5

11/19
B
X 6pcs
Tighten cam locks once panel 1 is in place.
1
B
B
B
B
B
B
2
3
B
Tighten cam locks once panel 1 is in place
(to make sure the curved edge of Part 1 and
Part 2 / 3 are in line).
Step 11
Step 10
C
AF
X 6pcs X 8pcs X 4pcs
A
A
A
A
A
A
C
C
C
C
C
C
C
F
F
F
F
F
1
C
A

12/19
Step 13
X 2pcs
L
X 1pc
I
J
X 4pcs
H
X 4pcs
G
X 4pcs
H
I
G
J
H
J
I
G
G
I
H
H
H
I
I
G
G
2
3
Step 12
X 2pcs
K
2
3
K
K
K
LL
L
L

13/19
Step 15
8
A
X 8pcs
9
A
A
A
A
A
Step 14
A
X 8pcs
6
7
A
A
A
A
A
A
A
A
A

14/19
Step 17
11
8
9
Step 16
B
X 8pcs
Tighten cam locks once panel 8 and 9 are in place.
8
10
B
B
B
B
B
9

15/19
Step 19
D
X 6pcs X 2pcs
Front
E1
DD
D
D
D
D
E1
E1
8
Front
6
9
Front
E1
Step 18
Tighten cam locks once panel 6 is in place.
BB
X 4pcs
8
B
B
B
B
6
9

16/19
Step 21
Front
Front
E1
E1
D
D
D
D
D
D
78
9
D
X 6pcs X 2pcs
E1
Front
E1
Step 20
B
X 4pcs
7
Tighten cam locks once panel 7 is in place.
B
B
B
B
B
8
9

Maximum Load Capacity:
Desk Top - 40 kg
Drawer - 5 kg
Your is now complete and ready for use!
REINE 2 DRAWER DESK
17/19
Step 22
Note: Move the inner ball bearing sliding part as
shown below to the front end on both sides
before inserting the drawer.
Note: Insert the sliding part (at drawer section)
into ball bearing part gently as shown below.
6
7

18/19
Care Advice
Care Instructions - PU Painting Finish Desk
Safety Warning
WARNING – Put locking devices on all drawers to prevent children opening them
and using them as steps.
WARNING – This product is intended to hold the maximum weight indicated.
Exceeding the maximum weight will result in instability and may cause injury.
Keep away and protect from direct sunlight and heat.
Do not place sharp materials (knife, fork, etc) directly onto your furniture as sharp
material may scrape and damage the finish.
Clean up spills quickly. Water left over a prolonged period of time may cause
damage. Alcohol, perfume, nail polishes, aftershave and some medication may
cause severe finish damage if not cleaned immediately.
Use a clean, soft, dry, lint free absorbant cloth to clean your furniture. Do not use
any detergent as they may contain ingredients that may react and damage the finish.
Clean, check and tighten all parts regularly.
Avoid of using corrosive or abrasive cleaner as this will void the product warranty.

19/19
Warranty 3 years
Product Warranty –valid for Australian customers only
Officeworks Ltd warrants that this product will be free from defects and work as intended
for 3 years from the date of purchase by the original customer.
If the product has any defects or does not work as intended during the Warranty Period,
Officeworks will, at its election and at its expense, repair or replace the product.
This warranty does not apply:
to cosmetic damage;
to damage caused by consumables used in connection with the product (such as
cleaning products);
where the product has not been used in accordance with all provided instructions;
to damage arising from fair wear and tear;
where the product has not been subject to reasonable use;
where the product has been intentionally or negligently damaged; and/or
if the customer has attempted to repair the product.
To make a claim under this warranty, please return your product with your receipt or proof
of purchase to your nearest Officeworks store or contact 1300 633 423.
This warranty is provided in addition to any rights you may be entitled to under the
Competitions & Consumer Act 2010.
Our goods come with guarantees that cannot be excluded under the Australian
Consumer Law. You are entitled to a replacement or refund for a major failure and
compensation for any other reasonably foreseeable loss or damage. You are also entitled
to have the goods repaired or replaced if the goods fail to be of acceptable quality and the
failure does not amount to a major failure.
½ ¾ ¿ À Á Â Ã Ä Å Ã Æ Â Ã Ä Æ Ç Ä Æ È ¾ ¿ É Ê Ë Ì Í Ê ¿ É Ê Æ Ê Î ¿ Ï À Â Ã Ä Æ Æ Ê È Ê Ï Ç Î Î Ã Ð ¿ Í Ï Ñ ¿ Î Ê Ò ¿ Æ Æ ¿ À Î Â Ë
Ó Å Â Ã Ä Ò Ã Ä Í Ñ Í Ï Á Ê Î Ã Á À Ã Ò Ô Ã Æ Ê ¿ Õ Ã Ä Î Ã Ä Æ Å Ä Æ À Ï Î Ä Æ Ê Ç Æ Ã Ñ Ä È Î É Ö Ç Í Ê ¿ É Ê Ð Ï É Ï Î Ò Ò Ò Ë Ã Å Å Ï È Ê Ò Ã Æ Á É Ë È Ã Ô Ë ¿ Ä