Otto WF298308 User manual

12
9
6
390
WF298308 / WF298309
WF305300 / WF305301
MONTAGEANLEITUNG
Please check that you have all the parts listed
before you start assembling, if you do 
that something is missing, do not 
assembly, please contact us immediately.
This set will be shipped by 2 boxes and they may arrive on
 days.If both packages arrived but parts missing,
please contact customer service.
Dieses Set ist in 2 Boxen enthalten. Wenn Sie keine vollen
2 Boxen erhalten, wenden Sie sich  an unseren
Kundenservice
NOTE:

sind, bevor Sie mit der Montage beginnen.
Wenn Sie festlegen, dass etwas fehlt, setzen

Sie uns sofort.
Achtung：
fest, bevor die Montage abgeschlossen ist！
all the hardware  the  assembly
is complete!

Stückliste
2
3
4
5
6
7
8
9
11
10 12
13
19 19
1
14
14 14
15
16
17
17
18

Part List-Stückliste WF298308/WF305300
x1
12 x1 3 x1
7x1 10x1 11x1
19x2

滚滚长江东逝水
4x1 5x1 6x1
8x1 9x1
20x1
Part List-Stückliste WF298309/WF305301
12x1
13x1 14x3 15x1
16x1 17x2 18x26

Hardware List- Hardware-Liste
WF298309/WF305301
x1
A
M8x50mm
x4
Bx12
C
x24
Dx2 Ex2 F
M8x20mm
M4x15mm
x8
Gx8
Hx8
J
x2
Kx4 Lx12 M
x16
Nx1 Px2
Q
x2
Rx26
Sx13
T
M8x30mm
M6x35mm
M8x40mm
M8x18mm
M8

1
2
1
2
3
4
5
A x 1
M8 x 50mm
B x 4 C x 4
A
B
C

E
3
4
6
7E
A x 1
M8 x 20mm
D x 4
A x 1
M8 x 20mm
D x 4 E x 2
A
D
E
A
D

5
6
A x 1
M8 x 20mm
D x 8
D
7
70%
A
F
F
M4 x 15mm
F x 2 G x 8
G

8
9
10
11
H
A x 1 H x 8 J x 8
M8 x 30mm
8
4
8
79
D
100%
7
A x 1
8
A
A
J
8
7

9
K
K
A x 1
M8 x 20mm
D x 8 K x 2
ADK
10 M8 x 18mm
L
70%
A x 1 L x 4
A

11 A x 1
L
100%
12
8
12
13
A
UP

13 A x 1 C x 6
M8 x 40mm
M x 6 N x 6 P x 1
A
M
C
N
P
M8
14 A x 1 C x 2
M6 x 35mm
Q x 2
A
Q
C
17
17
14
14
14
15
16

A x 1 M x 6 N x 6 P x 1
M8 x 40mm
AM
NP
M8
15
16
R
R x 2

17
18
T
18
18
18
S x 26
T x 13
19
20
N x 4 P x 1
P
N
N
M8
S
20

PISTONS
THIS IS PERFECTLY NORMAL
PLEASE NOTE
OTTOMAN OPERATING INSTRUCTIONS
IMPORTANT NOTICE
Once your bed frame is completely assembled, the slat unit will not operate correctly unless a mattress is placed on the slat frame. Position the
mattress on the slat frame whilst it is in the closed position.
- It takes a lot of force to make the initial movement of the ottoman. This is a design feature of the product so that it does not fall shut
- the nearer to being closed the ottoman is, the easier it is to move. When the ottoman is al most shut, it will close completely under its own weight.
When lowering the slat unit for the first time, take care to make sure it does not rub unevenly on the inside face of the side rails. If it does, the bed
has been assembled slightly out of square. This can be rectified by moving the foot end of the bed slightly to the left or right whilst leaving the head
end stationary.
The pistons used in the construction of this product are extremely strong and cannot be operated by hand when taken off the ottoman. All pistons
are tested for correct pressure and operation before being attached to the slat unit.
Initially it might appear that the pistons are very stiff when opening and closing the ottoman.
When fully assembled and the mattress is in position, please raise and lower the ottoman 4/5 times to ensure the gas piston
are fully lubricated.
WHY WON'T MY HYDRAULIC BED STAY DOWN？
1. In fact, nine times out ten the reason why hydraulic
won’t close is because you need to put your mattress
on top of the bed. Yep, it really is that easy. This is because
the hydraulic pistons need the weight of the mattress to
provide enough pressure to close your bed.
2.However, what if you’ve put your mattress on your bed
and you’re one of the unlucky ones who finds that their
hydraulic bed still won’t stay down?
As previously mentioned, they require pressure in order
to close. However, occasionally as well as placing the mattress
on the bed you will initially have to apply some physical force
yourself to close the bed. Don’t worry you won’t break it! ！！！
WARUM BLEIBT MEIN HYDRAULISCHES BETT NICHT UNTEN？
1. In neun von zehn Fällen liegt der Grund dafür, dass sich die Hydraulik nicht schließen lässt, darin, dass Sie Ihre Matratze oben auf das Bett legen
müssen. Ja, es ist wirklich so einfach. Das liegt daran, dass die Hydraulikkolben das Gewicht der Matratze benötigen, um genügend Druck zum
Schließen des Bettes zu erzeugen.
2. Was aber, wenn Sie Ihre Matratze auf Ihr Bett gelegt haben und zu den Unglücklichen gehören, die feststellen, dass ihr hydraulisches Bett trotzdem n
icht unten bleibt?
Wie bereits erwähnt, muss man Druck ausüben, um sie zu schließen. Gelegentlich müssen Sie jedoch nicht nur die Matratze auf das Bett legen,
sondern zunächst selbst etwas Kraft aufwenden, um das Bett zu schließen. Keine Sorge, Sie werden es nicht kaputt machen! ！！！
19