Outback Mayfair User manual

Elite Series Barbecues
Assembly and Operating Instructions for Outback® Mayfair/Tungsten,
Outback® Spirit/Titanium, and Outback® Performance/Platinum Hooded Gas Barbecues
0359
Photographs are not to scale.
Specifications subj ect to change
without prior notice.
WARNING
• For outdoor useonly.
• Read instructionsbeforeusing theappliance. Failure to followinstructions
could resultin death, seriousbodilyinjury, and/or propertyloss.
• Warning: accessible parts may be very hot. Keep young children away.
• Do not move the appliance during use.
• Turn offthegassupply at thegasbottle after use.
• Any modification oftheappliance, misuse, or failureto follow theinstructions
may bedangerousand will invalidate your warranty. Thisdoesnotaffect your
statutory rights.
• Retain these instructions for future reference.
• Leak test your barbecue annually. Check the hose connections are tight and leak
test each time you reconnect the gas bottle.
FOR YOUR SAFETY
If you smell gas:
1. Shutoffgasto theappliance.
2. Extinguish any open flame.
3. Open barbecue lid or hood.
4. Ifodour continues, discontinueuse and
contact your local dealer.
FOR YOUR SAFETY
1. Do not storeor use petrol or other flammable
vapoursor liquidsin thevicinityof thisor any
other appliance.
2. Agas bottle notconnected for use shall notbe
stored in the vicinityofthisor anyother
appliance.

2
Parts List
Quantitiesvary according to model purchased. Specifications subject to change without prior notice. For more
details on hardware, please see ‘Hardware Reference Diagram’.
Pre-Assembled Component
Quantity varies accordi ng to model purchased
 Appear ance, size, and construction maydiffer according to model purchased
Outback® Titanium/Platinum, these two models were approved by TUV
CODE PART QTY Mayfair/
Tungsten Spirit/ Titanium Performance/ Platinum
HOOD
A1 Hood H andle 1   
A2 L/H Hood Handle Bracket 1   
A3 R/H Hood H andle Bracket 1   
A4 Hood (Pre-Assembled to Body) 1   
A5 Hood Panel 1   
A6 Heat Indicator and Nuts 1   
BODY
B1 Barbecue Body 1   
B2 Burner 2 3 6
B3 Burner Clip 2 3 6
B4 Control Panel 1   
B5 Knob 2 3 6
B6 DripTray 1   
B7 Drip Pan 1 
B8 Foil Liner 1 
B9 Lava RockBasket 2   
B10 LavaRockPack(inBasket) 2   
B11 Grill 2   
B12 Griddle 1  
B13 Hose 1 
B14 Warmi ng Rack 1   
TROLLEY
C1 L/H Side Shelf 1   
C2 Side Shelf Shi eld 1   
C3 Front Left Endcap 1   
C4 Rear Left Endcap 1   
C5 Utensil Tray 2   
C6 R/H Side Shelf 1   
C7 R/H Insert 1   
C8 Front Left Leg 1   
C9 Rear Left Leg 1   
C10 FrontRightLeg 1   
C11 Rear Right Leg 1   
C12 Bottom Slat Assembly 1   
C13 Base Tray 1   
C14 Gas Bottle Holder 1   
C15 TrolleyF oot 1   
C16 Hubcap 2   
C17 Wheel 2   
C18 Locknut 2   
C19 Axle 1   
C20 Retaining Rod 1   
C21 Gas Bottle Strap 1   
HARDWARE
D1 Countersunk Screw, M4x15 4   
D2 Screw, M6x15 24   
D3 Washer 4   
D4 Screw, M6x35 16   

3
Parts Diagrams
Quantitiesvary according to model purchased. Specifications subject to change without prior notice. For more
details on hardware, please see ‘Hardware Reference Diagram.’
B10
B9
A1
B3C2
B4
B5
B6
B2
C3
C5C4C1
B8
C6
B7
A4
A2 A3
C12
B12
B14
B13
B11
C15
C14
C16
C17
C18
C19
C9
C8
C11
C21
C20
C7
C10
A6
A5
B1
C13

4
Hardware Reference Diagram
Specifications subject to change without prior notice.
D1
D2
D2 (screw)
D3(washer)
D2
D4

5
AttachtheFrontRight Leg (C10)tothe Trolley Foot (C15)
Assembly
IMPORTANT!
• ToolsRequired:Medium size flat blade or Phillips/Crosspoint screwdriver, adjustable spanner or metric
spanner set
• The assembly of this barbecue requires 2 people.
• Carefully unpack the trolley box and remove all internal packaging before commencing assembly.
• Carefully remove the box lidfrom the body box and remove all internal packaging and parts inside the body.
• The inlet connection of the gas rail assembly on the BBQ body is lower than the body. You must never allow
the pipe to rest on the ground during assembly as serious damage could result. We recommend the body is
left sitting inthebox untilrequiredfor assembly totrolley.
• Whilst everycare is takeninthemanufactureof this product, caremust betaken duringassembly incase
sharp edges are present.
1
Attach the Rear Right Leg (C11) to the Trolley Foot (C15). The legs are a push fit onto the trolley foot and on
the gas bottle holder. In case of difficulty, they may need tapping lightly with a softface mallet. Take care not to
damage parts.
2

6
AttachtheBottom Slat Assembly (C12)tothe Base Tray (C13)usingtheScrews (D2).
Attachtheleg assembly totheBaseTray (C13) usingthe Screws (D2).
4
3

7
Align the Gas BottleHolder(C14)withthe Slat Assembly (C12).
AttachtheFront Left Leg (C8) andRearLeft Leg(C9)totheGas BottleHolder (C14).
Threaded
Insert
6
5

8
AttachtheGas BottleHolder (C14)tothe Bottom Slat Assembly (C12)usingtheScrews (D2)
and Washers (D3).
Insert the axle (C19) through the clamping brackets on the gas bottle holder (C14) and tighten the clamp
screws. Take care not to over tighten these screws which will damage the plastic Gas Bottle Holder.
8
7

9
Place the Wheels (C17) onto the Axle (C19) and secure with Locknuts (C18).
Carefully turnthecompletedtrolley over, right sideup.
10
9

10
CAUTION! Care must be taken to ensure hood does not fall open
unexpectedly or that the hood surface is damaged when set on the ground.
Carefully turntheBarbecueBody (B1) upside down andremovetheDrip Tray (B6). Attachthe
R/H Side Shelf (C6) to the Barbecue Body (B1) using the Screws (D2).
AttachtheFront Left Endcap(C3)totheBody (B1) usingthe Screws (D2).
12
11