Outback TPA101-2 Quick reference guide

ASSEMBLY & OPERATING INSTRUCTIONS
Meteor Gas Barbecue
Model: TPA101-2

Chapter 1: Safety Information
Chapter 2: Package Contents List
Chapter 3: Hardware Contents List
Chapter 4: Assembly
Chapter 5: Leak Testing
Chapter 6: Important Information
Chapter 7: Gas, Regulator and Hose
Chapter 8: Installation
Chapter 9: Operation
Chapter 10: Care and Maintenance
Chapter 11: Technical Specifications
Chapter 12: Troubleshooting
Chapter 13: Parts Diagram
Chapter 14: Parts List
Page Table of Contents
3
4
6
7
13
14
15
16
17
20
22
22
23
24
2

3
Safety Information
WARNING
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
For outdoor use only. Not for commercial use.
Read instructions before using the appliance. Failure to follow
instructions could result in death, serious bodily injury, and/or property
loss.
Warning: accessible parts may be very hot. Keep young children and
pets away.
Do not move the appliance during use.
Any modification of the appliance, misuse, or failure to follow the
instructions may be dangerous and will invalidate your warranty. This
does not affect your statutory rights.
For Flare-up control please refer to the ‘OPERATION’ section of this
manual.
Retain these instructions for future reference.
Turn off the gas supply at the gas bottle after use.
Leak test annually, and whenever the gas bottle is removed or
replaced. Check that the hose connections are tight and leak test each
time you reconnect the gas bottle.
FOR YOUR SAFETY
If you smell gas:
Shut off gas to the appliance.
Extinguish any open flame.
Open barbecue lid or hood.
If odour continues, discontinue use and contact your local dealer.
FOR YOUR SAFETY
Do not store or use petrol or other flammable vapours or liquids in the
vicinity of this or any other appliance.
A gas bottle not connected for use must not be stored in the vicinity of
this or any other appliance.

Package Contents List
4
R. Axle Bushing--------2 pcs.Q. Condiment rack handle--1 pc.P. Front Panel -----1 pc
O. Condiment rack panel------1 pc.N. Lighting Stick----1 pc.M. Bottom Panel -----------1 pc.
L. Wheel---------------------2 pcs.K. Wheel Axle-----------1 pc.J. Warming Rack--------------1 pc.
I. Cart Frame, Front ------1 pc.H. Cart Leg, Rear Right-----1 pc.G. Cart Leg, Front Right-----1 pc.
F. Cart Brace, ------2 pcs.E. Side Panel----2 pcs.D, Cart Leg Foot-----2 pcs.
C. Cart Leg, Rear Left----1 pc.B. Cart Leg, Front Left------1 pc.A. Firebox--------1 pc.

5
Package Contents List
ZA. Cooking Grid-----------2 pcs.Z. Flame Tamer------------4 pcs.Y. Grease Cup--------------------1 pc.
Carefully unpack the packing box and remove all contents before commencing assembly. Make sure that you
obtain all correct package contents.
X. Grease Tray -1 pc.W.. Control Knob--------------1 pc.V. Bezel---------------------------1 pc.
U. Left side shelf with side shelf
front panel---------1 pc.
T. Side Burner bowl assembly frame
with Side burner control panel-----1
pc.
S. Cart Frame, Rear------1 pc.

Hardware Contents List
6
Before beginning assembly, make sure all parts are present. Compare parts with package contents list and
diagram above. If any part is missing or damaged, do not attempt to assemble the product. Contact customer
service for replacement parts.
•Tools required for Assembly.
Phillips Screwdriver (not included) and Wrench (not included)·
• Note: The left and right sides of the grill are on your left and right as you face the front of the grill.
Preparation
81/4-in. Flat WasherGG
81/4-in. x 65-mm Round Head ScrewFF
25/32-in. x 6-14 stage screwHH
1Allen KeyEE
181/4-in. Lock WasherDD
181/4-in. x 10-mm Round Head ScrewCC
245/32-in. Lock WasherBB
245/32-in. x 8-mm Round Head ScrewAA
Required for assembly (pcs)
DescriptionPack

AA BB CC DD EE GG FF HH

Assembly
Fig. 2
Fig. 3
Fig. 1
Fig. 4
E
C
B
F
B
C
E
H
G
F
G
H
UNPACKING
CAUTION: Obtain the aid of an assistant when handling large
or heavy grill components.
1. Remove all packing material from around grill exterior.
2. Open Firebox lid and remove packing materials and
components from inside Firebox.
3. With the aid of an assistant, lift the Firebox out of the
shipping box and place on protected flat surface. Be careful not
to damage hose and regulator.
4. Refer to Parts Lists to check that all parts are present.
5. Inspect the grill for damage as you assemble it. Do not
assemble or operate the grill if it appears damaged.
IMPORTANT: Refer to the package Contents and Hardware
Contents on page 4, 5and 6 when assembling Grill Cart.
1. Grill Cart Assembly
(a) Firstly, attach two Cart Leg Foots (D) to left side legs B&C.
Then use 4 AA Round Head Screws and 4 BB Lock Washers to
attach Side Panel, Left (E) to Cart Leg, Rear Left (C) and Cart
Leg, Front Left (B). Attach so that flat surface of Side Panel will
be on Grill exterior. See (Fig. 1).
(b) Use 4 CC Round Head Screws and 4 DD Lock Washers to
attach Cart Brace, Left (F) to Cart Leg, Front Left (B) and Cart
Leg, Back Left (C). Attach Cart Brace so that flat side will face
Cart Interior and wide lip faces down. See (Fig. 2).
(c) Using 4 AA Round Head Screws and 4 BB Lock Washers to
attach Side Panel, Right (E) to Cart Leg, Rear Right (H) and
Cart Leg, Front Right (G). Attach so that flat surface of Side
Panel will be on Grill Exterior. See (Fig. 3).
(d) Use 4 CC Round Head Screws and 4 DD Lock Washers to
attach Cart Brace, Right (F) to Cart Leg, Front Right (G) and
Cart Leg, Back Right (H). Attach Cart Brace so that flat side will
face Cart Interior and wide lip faces down. See (Fig. 4).
Remark: The lighting stick is preassembled on the Cart Leg,
Front Right (G)
7
D
AA BB
E
DDCC
AA
BB
CC DD

8
Assembly
Fig. 5
Fig. 6
2. Wheel Assembly
Remove Axle Bushings (R) and Screws from the
ends of Wheel Axle (K). Insert Wheel Axle (K)
through Cart Leg, Front Right (G) and Cart Leg,
Rear Right (H). Place Axle Bushing and Wheel
(L), cone side facing Leg, on each end of Axle.
Secure Wheels to Axle with previously removed
Screws. See (Fig. 5).
3. Bottom Panel Assembly
(a) Use 4 FF Round Head Screws, 4 DD Lock
Washers and 4 GG Flat Washers to attach and
securely tighten the bottom of the left cart legs (B
& C) to the Bottom Panel (M). See (Fig. 6).
(b) Repeat step 3(a) to attach & securely tighten
Bottom Panel (M) to Right Cart Legs (G & H).
4. Front Panel Assembly
(a) Use 2 AA Round Head Screw and 2 BB Lock
Washer to attach Condiment rack handle (Q )to
Condiment rack panel (O) (Fig 7).
FF
C
M
G
H
K
L
R
K
Fig. 7
O
Q
H
G
FF
DD
DD
GG
AA
BB
GG

9
Assembly
(b) Firstly, insert the two holes on the bottom of left &
right side of the condiment rack panel to the rotating
shaft on Front Left Cart Leg (B ) and Front Right Cart
Leg (G) use 2 HH Round Head Screws to attach the
Condiment rack panel (O) to the Front Left Cart Leg (B
) and Front Right Cart Leg (G) See (Fig. 8)
(c) Use 4 AA Round Head Screws and 4 BB Lock
Washer to attach the Front panel˄P˅to the Front Left
Cart Leg (B) and Front Right Cart Leg (G) . see (Fig. 9).
(d) Use 4 AA Round Head Screws and 4 BB Lock
Washers to attach Cart Frame, Front (I) to Front Left,
Cart Leg (B), And Front Right, Cart Leg (G). Attach Cart
Frame so that flat side will face Cart Interior and wide
lip faces down. See (Fig. 10).
(e) Use 4 AA Round Head Screws and 4 BB Lock
Washers to attach Cart Frame, Rear (S) to Rear Left,
Cart Leg (C), And Rear Right, Cart Leg (H). Attach Cart
Frame so that flat side will face Cart Interior and wide
lip faces down. See (Fig. 10).
5. Firebox Assembly
NOTE: Obtain the aid of an assistant to lift the
firebox. Be sure the hose and regulator hang outside
the cart when placing Firebox.
(a) With the aid of an assistant, lift the Firebox (A) and
carefully place it onto the grill cart. See (Fig. 11).
Fig. 8
Fig. 9
Fig. 10
Fig. 11
O
B
G
S
C
H
A
M P
B
I
G
HH
AA
BB
AA
BB
AA
BB B
G

10
Assembly
(b) Raise firebox lid and from inside the Firebox use 4
CC Round Head Screws to attach the sides of
Firebox to Cart Brace, Left (F) and Cart Brace, Right
(F). Raise Firebox slightly to align holes for
inserting and tightening screws. See (Fig. 12).
(c) From the inside of the cart, use 2 CC Round Head
Screws and 2 DD lock washers, attach Rear Right
Cart Leg (H) and Rear Left Cart Leg (C) to the
firebox. See (Fig. 13).
6. Side Burner Shelf Assembly
(a) Attach Side Burner bowl assembly frame (T) with
the side of Front Right Cart Leg (G) and Rear Right
Cart Leg (H) on Loosen 4 pre-assembled AA Round
Head Screws and 4 BB Lock Washers. See (Fig.
14). Note: Still do not fully tighten the four screws at
this point.
(b) Align the holes on Side Burner bowl assembly
frame (T) with the holes on the side of firebox, and
attach from inside of firebox using 2 CC Round
Head Screws. See (Fig. 15).
(c) Connect Side Burner shelf front panel to Main
control Panel with 1 AA Round Head Screw and 1
BB Lock Washer .Tighten all screws. See (Fig. 15).
(d) Repeat steps (a) through (c) to install left side shelf
(U˅.
Fig.12
Fig.14
Fig.15
T
G
H
Fig.13
H
C
CC
CC
DD
CC
T
CC
AA
BB