OUTLINE S.R.L.
Via Leonardo da Vinci, 56
25020 Flero (Brescia) Italy
Tel.: +39 030.3581341
Fax +39 030.3580431
www.outline.it
10
LEVEL AND DELAY
The Level and Delay pages allow the control of the
amplier output levels and delay times. Once in one
of the two pages, click on any given output and adjust
the level or delay by turning the rotary encoder.
When an output is selected, the white LED behind the
encoder will light up, indicating that the parameter
can be altered.
Note that it is possible to select multiple outputs
at the same time and simultaneously control their
relative levels and delay. Selected outputs will display
a check mark ✓ next to the speaker preset name.
Clicking the ‘Set Step Size’ button on the top of
the display, allows the selection of the change steps
to be applied when rotating the encoder, if ner
adjustments are necessary. Level change steps can
be set from 1dB (default) to 0.1dB, while delay steps
can be from 10ms to 0.1ms (default is 1ms). For the
delay controls, it is also possible to select between
metric (m) or imperial (ft) systems.
MATRIX
The TTM amplier series has an internal 4 x 4
mixing matrix. The Matrix page shows the internal
matrix outputs and the matrix inputs that are routed
to them. It is possible to change the routing by
clicking on one of the ‘INPUT’ labels and selecting a
new input from the list. These can be any of the four
matrix inputs, or a mix of input channels 1 + 2, or
channels 3 + 4.
Other routing and mixing congurations can be
achieved from ArmoníaPlus. In such cases, the TTM
will display ‘CUSTOM’ in the input label.
SOURCE SELECT
The Source page shows what amplier input
sources are active in each of the 4 internal matrix
inputs. These sources can be any of the 4 amplier
analogue inputs, AES3 or Dante inputs. Manual
selection of different sources, as well as conguration
of an automatic backup selection based on signal
presence, can be achieved from ArmoníaPlus.
SNAPSHOTS
Snapshots are full amplier congurations that
can be saved onboard of the device, and later recalled
when necessary. In the Snapshots page, it is possible
to load up to 50 different amplier congurations
that have been previously saved onboard using
ArmoníaPlus. To load a new snapshot to the amplier,
scroll through the list, select one of the snapshots
available, and click the ‘Load’ button at the bottom of
the screen.
OUT CONFIG
The Out Cong page allows quickly bridging the
amplier’s outputs 1 and 2, and/or outputs 3 and
4. Simply click the ‘Bridge’ button to perform the
operation, and ‘Unbridge’ to revert to the default
conguration.
When n-way loudspeaker presets have been load
to n-speaker channels, a new button labelled ‘Split’
will show up in this page. It is possible to split the
ways for individual conguration and control by
clicking this button.
HOME
The Home page displays the amplier’s output
channels, their level, and the speaker presets
assigned to them. From this page, it is also possible to
mute/unmute the outputs by clicking the respective
loudspeaker icons .
FRONT PANEL CONTROLS
The front panel comprises a multitouch capacitive
display (1), a rotary encoder with pushbutton (3), a
power status LED (4), and a ‘Back/ArmoníaPlus
Callback pushbutton (5). Users can select what
parameters to control and navigate through the
different display options and pages available, by
touching the screen, rotating and pushing the rotary
encoder, or pushing the ‘Back’ button. Control of
some specic parameters, such as output level and
delay, are only possible by rotating the encoder.
From the main menu (2), it is possible to access all
the different pages from where control operations
can be performed.
BACK
OUTLINE TTM 8K4 HOME
1- VEGAS 12 CX >60 dB
2- VEGAS 12 CX >60 dB
3- SPEAK...MODEL >60 dB
4- SPEAK...MODEL >60 dB
1 2 3 4
5
