Outsunny 860-020V01BU User manual

ASSEMBLY INSTRUCTIONS
860-020V01BU

1.
.
3.
SAFETY INFORMATION
1.
2.Assemble the item on a soft, non-abrasive surface such as carpeting
3.
Recommended maximum sitting weight for the sofa set
Before beginning assembly of product, make sure all parts are present.
Compare parts with parts list.If any part is missing or damaged, do not attempt
to assemble the product and contact us immediately
to avoid damage.
Estimated Assembly Time: 120 minutes
assemble or install the product.
1
350 160

PACKAGE CONTENTS
PART DESCRIPTION QUANTITY
E
F
1
1
x
Qty.
asher
Qty.
Qty. Qty.
Plastic
Qty.
Plastic
Qty.
Extra 6
6
Extra 2
28
Extra 1
8
Extra 1
20
Extra 1
Plastic
shackle
Qty. 10
Extra 1
HH
Ruler
- Use this ruler to help correctly identify the screws.
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 105 110 115 120 125 130 135 140
2
2
84
X 2

ASSEMBLYINSTRUCTIONS
FRAME ASSEMBLY
Hardware Used
M6 x 35 L Bolt
M6 Washer
x 2
x 2
1.
1
2.
2
Hardware Used
3.
Attach two the " I " plastic foot (FF) to the lower corner of
the seat frame (B) , and two the " L '' plastic foot (GG) into
the lower corner of the back frame (A) by using M6 x L
bolt (ZZ) and Knob (DD). Then tighten all bolts by using
allen wrench.
3
Hardware Used
M6 Washer
x 8
x 8
Align two holes of the back frame (A).
Insert an M6 x 35 L bolt (AA) through
M6 washer (CC), with the seat frame
(B). Do not tighten completely. Repeat
Align all four holes of the side frame (C). For
each hole, insert M6 x 35 L bolt (AA) through
M6 washer (CC), the seat frame (B) and
back frame (A). Repeat this step for the
oposite side. Do not tighten completely.
x 4
x 4
x 2
x 2
Knob
" I " Plastic Foot
" L " Plastic Foot
ZZ
ZZ
ZZ
ZZ
ZZ
ZZ
M6 x 35 L Bolt
M6 x 35 L Bolt

ASSEMBLY INSTRUCTIONS
FRAME ASSEMBLY
Hardware Used
x
x
4.
4
5.
Hardware Used
6.
Attach one the " L " plastic foot (GG) to the lower corner
of the seat frame ( E) , and three the " L '' flastic foot
(GG) into the lower corner of the back frame (D) and
side frame (F) by using M6 x L bolt (ZZ) and Knob
(DD). Then tighten all bolts by using allen wrench.
Hardware Used
Align two upper holes of the back frame ( D).
Insert an M6 x 35 L bolt (AA) through M6
washer (CC) with the seat frame (E ). Then align
the side holes of the back frame ( D) insert
an M6 x 5 L ( ) through M6 washer (CC). Do
not tighten completely. Repeat this procedure
Align two holes of back frame (D) the oposite side
with the side frame ( F) insert an the M6 x 35 L bolt
(AA) through the M6 washer (CC). Then align two
holes before of the side frame (F) with the seat
frame (E ) insert the M6 x 35 L bolt (AA) and the
M6 x L bolt ( ) through the M6 washer (CC) .
Do not tighten completely. Repeat this procedure
M6 x L Bolt
Knob
" L " plastic Foot
M6 x 35 L Bolt
M6 Washer
M6 x 35 L Bolt
M6 Washer
x 8
5
6
ZZ
x 8
x 8
X 5
X 5
D
F
D
F
35

Hardware Used
Hardware Used
Attach four the " L " plastic foot (FF) to the lower corner
of the table (G) by using M6 x 25L bolt (ZZ) and Knob
(DD). Then tighten all bolts by using allen wrench.
x 4
x 4
x 4
Knob
" L " Plastic Foot
ZZ
ZZ
ZZ
ZZ
ZZ
ZZ
HH X 10
Plastic shackle
Attached the products by plastic shackles.
FRAME ASSEMBLY
Hardware Used
Put the glass (H) on the table (G). And make
adjustments. The assembly of this product
has been completed.
7
8
9
7.
8.
9.
M6 x 35 L Bolt

6
ITEM NO. CTN NO. INCLUDING
860-
020BU/GY
1
2 Pilow + 3 seat cushion + 2 back cushion +
1 Table + 1 Glass + 1 Back frame of
2
4 seat frame of Armless chair + 1 seat
cushion+ 2 back cushion + 8 side frame
of Armless chair + 3 back frame of
armless chair
3
2 seat frame of Corner chair + 2 seat
cushion+ 4 back cushion + 2 side frame of
Corner chair + 2 back frame of Corner chair
HH
Right corner chair - Side
Right corner chair - Back
Left corner chair - Side
Left corner chair - Back
X
Y
Armless chair + Hardware + Plastic foot
US
001-877-644-9366
[email protected]
CA
001-855-537-6088
[email protected]
Seat