OUZIM BioEngine 3 User manual

1
MANUAL FOR BioEngine 3
1. Notice for Use......................................................................................................................................................................................... 2
1.1 Access Control Wiring Diagram....................................................................................................................................................... 2
2. Install the Device.................................................................................................................................................................................... 3
2.1 Device Installation Environment......................................................................................................................................................3
..........................................................................................................................................................................................................3
2.2 Device Installation Steps..................................................................................................................................................................3
3. Use Introduction..................................................................................................................................................................................... 6
3.1 User Interface and Enter the Main Menu........................................................................................................................................6
3.2Identifying Methods......................................................................................................................................................................... 6
4.User Management................................................................................................................................................................................... 7
4.1 User Registration............................................................................................................................................................................. 7
4.2Modify User Information.................................................................................................................................................................. 7
4.3 Download & Upload Data................................................................................................................................................................ 8
5. Download the Report............................................................................................................................................................................. 8
6. Setting..................................................................................................................................................................................................... 9
6.1 Device...............................................................................................................................................................................................9
6.2 Time Setting..................................................................................................................................................................................... 9
6.3 Network......................................................................................................................................................................................... 10
6.4 Initial.............................................................................................................................................................................................. 10
6.5 Access Control Function................................................................................................................................................................ 10
7. Record View.......................................................................................................................................................................................... 11
7.2 Registration Information............................................................................................................................................................... 11
7.3 Device Information........................................................................................................................................................................ 11
8. Device Administrator Clearing Methodl.............................................................................................................................................. 11

2
1. Notice for Use
1.1Access Control Wiring Diagram
1）The device and the lock are on the same power supply diagram
2）The device and the lock are on different power supply diagram

3
(Note: Need to connect a diode in parallel at both ends of the electric lock to prevent the back electromotive force released by
the electromagnet from burning out the access control system.)
2. Install the Device
2.1 Device Installation Environment
1) Recommended Install Environment
Install the device indoors or outdoors, the ambient light source
installation environment lighting 0-8000LUX. When you install the
device indoors, away from the window and door for 3 meters, and
light source for 2 meters. Avoid direct sunlight when installing
outdoors.
2) Several Location Which Will Affect Installation
1.Direct Sunlight 2. The sun shines through the window 3. The sun is oblique through the window 4. Light irradiation at close
range
(outdoors) (indoors) (indoors) (indoors)
2.2 Device Installation Steps
1) It is recommended that the height from the baseline to the ground is 1.25m (suitable for height range 1.5m -1.8m), it can be
adjusted according to the overall height of the user. After the installation height is determined, the installation positioning
template will be affixed to the installation location. Drilling cable entry and fixing holes according to the positioning template
(picture 1)
2) Remove the bottom of the fuselage screws with screwdriver (picture 2)
3) Separate the device from the bottom cover (picture 3)
4) Fix the seal ring and the bottom of the bottom cover and fixed it on the wall (picture 4)
5) Align the device with the mounting tabs of the bottom cover and pull it down into the mounting position (picture 5)
6) Screw the device and bottom cover firmly (picture 6)
Picture1 Picture 2 Picture3 Picture4 Picture5 Picture6

4
2.3 Distance from Staff to Device
Recommended distance between the machine and the machine is 0.8 meters
(for height range of 1.55-1.85 meters). It can be adjusted according to the effect
face images the device obtain; when the face image is displayed large, it can be
moved backwards appropriately; when the face image is displayed small, it can
be moved forward properly.
2.4 Staff Facial Expressions and Standing Posture
1) Recommended Facial Expressions and Several Kinds of Facial Expressions that Affect Recognition:
Right Wrong
2) Recommended Staff Standing Posture and Several Kinds of Recognition Posture that Effect Standing Posture: (Note: In the
process of face registration and identification, please maintain a natural look and standing posture.
Right Wrong

5
2.5 The Use of Device
Recommended location and method:
In the process of face registration and identification, the installation position of the equipment must be kept unchanged. If the
equipment needs to be moved, the installation height must be the same as the installation environment. Otherwise, the
identification effect of the equipment may be deteriorated.
Several methods which will affect face recognition:

6
2.6 Press the fingerprints
Right Fingerprint heart Too biased Tilt Too down
misalignment
Tips: fingerprint center as far as the center of the window
Please use the correct way to press the registration and comparison, to avoid improper operation caused by degradation of
recognition performance.
3. Use Introduction
3.1 User Interface and Enter the Main Menu
In the initial interface, click the settings icon in the top right corner.
In the case where an administrator has been set, the administrator will be authenticated and enter the main menu.
3.2 Identifying Methods
In the initial interface, the user recognizes through the face, fingerprint, ID/IC card, and password verification method. After the
verification is passed, the door opening record will be saved on the device. The voice prompts “Thank you!”After the employee
has successfully verified, the user will return to the initial interface.

7
4. User Management
Enter the main menu and click “User ”to enter the user management interface.
4.1 User Registration
New employees enter the work number and name of the staff face, fingerprint, ID / IC card and password registration. The device
supports T9 input method.
4.2 Modify User Information
There are two ways to find the specified user in the "Modify" interface
1) Click the icon in the upper left corner to enter the editing interface, and enter the corresponding ID number to find the
specified user;

8
2) Click on the user's name or face and fingerprint pattern to enter the “Modify User”interface. Enter the editing interface from
the “Modify” column and enter the corresponding ID number and confirm it, then enter the user's data modification interface; Data
modification includes name, card No., password, permission, access control settings; face and fingerprint re-recording or deleting
users.
LockCtrl:
The user access control settings are based on the user's needs.
You can enter this menu to view the access control settings status of a user:
That is, the user's daily time period, click "Access Control Settings" to enter the Sunday-Saturday time period selection.
4.3 Download & Upload Data
Download data to the U disk backup, to prevent data loss and upload data conveniently in the future.
You can upload employee’s information from U disk to several access control, eliminating duplication of input operations.
5.Download the Report
Steps:
1) Insert the USB flash drive into the U-DISK port of the machine.
2) Go to the main menu and click on “Report”.
3) Click “Logs”, and the “Working”download will start recording to the U disk. After the
download is completed and the message “Download Successful”is displayed, the U disk can
be pulled out.
4) The original record file is generated in the U disk and can be viewed on the computer with a
notepad.

9
6.Setting
Enter the menu, click "Settings"
6.1 Device Setting
Click “settings” to enter setting menu
Languages
English or other language for optional
Admins:
0 to 10 optional
Volume:
0 to 10 optional
Verify Mode:
FC/face, FP/fingerprint, P/password, C/ID/IC card
Verify Screen:
The time that back to the menu after verification
Screen Saver
Time to display screen saver
Sleep Time:
To set the sleep time after screen saver mode
Set Bell
To set the time for bell ringing, up to 24 rings can
be set in a day
Serial Settings:
AB/Disable
6.2 Time Setting
Under the settings menu, click “Time” to enter the time setting, you can set the year, month,
day and time. After setting, press “OK”to save automatically.

10
6.3 Network
Under the advanced settings menu, click “Network” to enter the network settings (you can set the Device No., ETH, WiFi, Port No.,
Net PWD, Server IP, ServerPort, Realtime Req).
When you need to start real-time monitoring, set the corresponding "Server IP" and "Server Port" and set "Realtime Req" to "Yes".
1) Select whether to use wired network, the default is Ethernet at open state, you can enter
the Ethernet setting interface, configure the IP address, subnet mask, default gateway,
according to the actual network environment.
2) WiFi
Enter the Wi-Fi network Select "Yes" to open the Wi-Fi network communication function,
enable DHCP by default or select "No" to turn off the IP setting manually, then enter "Select
Network" to select the WIFI signal which need to connect, finally enter the password to
connect Wi-Fi network.
6.4 Initial
Advanced settings menu Click “Initial ”to enter the initialization interface, you can reset
Default, delete all logs/users/all manager/all data, and upgrade the firmware, delete the
operation password unified to 8282. (Reset Default will not clear user data and logs. Deleting
all data will erase all data and reset default. Please use with caution!)
6.5 Access Control Function

11
Click “Setting” to enter Settings menu, then click "LockCtrl" to enter the LockCtrl (you can set the “Time Setting”, “Users to Open”,
“Unlock Time”, “Sensor Type”, “Sensor Delay”“Anti Passback”, “Alert Delay”, “Turn Off Alarm”, “Tamper Alert”, “Wiegand format”,
“Wiegand Output”, “Wiegand Input” and “Door Status”).
Users to Open:
The definition of the time interval for unlocking every day
Unlock for:
Require a few users to confirm before they can open the door at the same time
Sensor Type:
The type of door magnet: there are three types: No, Open Type, Closed Type; “No” does not
use the door switch, “Open Type” refers to the case of the door closed normally open magnet,
“Closed Type” under the door magnet is closed.
Sensor Delay:
Open the door after some time before starting the alarm, this time is the door magnetic delay.
Anti Passback:
Prevent trailing out, Yes/No
Alert delay:
After triggering tamper switch of the machine, start alarm if over the delay time
Turn Off Alarm:
Tamper Alert:
Yes/No
Wiegand Format:
Formats of WG input and output is the 26 or 34 optional, the default WG26
Wiegand Output
User ID/Card Number
Wiegand Input
User/Card Number
Door Status
In/Out
7. Record View
7.1 Record View
Viewing Administrator user record:
Enter ID, select the time of starting and ending. Click "OK" to check the employee's face, fingerprint, ID / IC or time when password
recognition successful in this period.
(Note: The confirmation method FC is face recognition, FP is fingerprint recognition, C is ID / IC card recognition, P is password
recognition.)
7.2 Registration Information
View user registration, management registration, attendance records, face, fingerprint, ID / IC card, password registration and other
information.
7.3 Device Information
Check manufacturer(MFG), date of manufacture (Mfg. Date) and firmware version(Firmware).
8. Device Administrator Clearing Method
With the machine turned on, use a tool such as a small screwdriver to insert the device into the middle
hole of the bottom of the device and hold the button inside for 3 seconds to clear the device
administrator.