Grants Automaton AN1404 User manual
AN1404 4G Door Station 2 Revision R11 Feb. 2020
TABLE OF CONTENTS
IMPORTANT SAFETY INSTRUCTION ...................................................................... 3
AN1404 4G DOOR STATION INTRODUCTION ........................................................ 4
AN1404 4G DOOR STATION WITH ACCESSORIES................................................ 4
INSTALLATION............................................................................................................... 5
AN1404 4G Door Station Unit Introduction................................................................... 5
Wiring Diagram .............................................................................................................. 7
LED Indicator ............................................................................................................... 8
AN1404 4G DOOR STATION OPERATION................................................................. 8
To Enter System Menu.................................................................................................... 9
Enter Listener Monitoring Mode .................................................................................. 10
Enter Access Control Mode .......................................................................................... 10
Enter Programming Mode............................................................................................. 10
Programming..................................................................................................................11
Door/ Gate Release ..................................................................................................... 13
Check 4G Signal Strength ........................................................................................... 14
Check Relay and Detect Status ................................................................................... 14
Door Opening Detection ............................................................................................. 15
Panel Opening Detection................................................................................................15
Administrator Number....................................................................................................15
Check a Log of Dial In and Dial Out Numbers Via E-Mail Or SMS.............................16
How to program checking the log of dial in numbers via SMS...................................... 17
USER COMMANDS......................................................................................................... …19
HOW TO RESET THE HARDWARE WHEN YOU FORGET YOUR PASSWORD......…20
SPECIFICATIONS .......................................................................................................... 21
QUICK PROGRAMMING VIA SMS............................................................................. 22
AN1404 4G Door Station 3 Revision R11 Feb. 2020
Thank you for purchasing AN1404 4G Door Station. Please read this manual carefully before
using. Be sure to keep this manual for future reference.
IMPORTANT SAFTY INSTRUCTIONS
When using this AN1404 4G Door Station, basic safety precautions should always be followed to
reduce the risk of fire, electric shock and personal injury. Please read the following before using
your equipment.
1. Follow all warning and instructions on the product.
2. Unplug all the connections of product before cleaning. Do not use liquid cleaners or aerosol
cleaners. Use a damp cloth for cleaning.
3. Do not use this product near water.
4. Do not use this product near an area where there is a potential of gas leaks or near any fumes
that can be explosive.
5. Do not place this equipment near or over a radiator or any other heat source.
6. Do not overload the wall outlet or power cord where the power adapter is installed. This can
result in fire or electric shock
7. Avoid spilling liquid on this equipment and do not insert any objects through the ventilation
slots.
8. Avoid using the equipment during an electrical storm. There is a remote risk of electrical shock
from lighting.
AN1404 4G DOOR PHONE INTRODUCTION
The 4G Door Station AN1404 is an intercom system and access control device which can be installed
at the entrance of a building, gate fence or door. The device can operate on local 12-24volt AC or
DC power. It enables you to speak with visitors from any location on or off the premises.
Door or gate release is activated from your phone keypad by pressing * duration the conversation and
can also be activated by calling the SIM card in the unit from an authorized phone number (guest). The
door unit will recognize an authorized phone (guest) number calling it and will then not answer the call,
but will release the door or gate. This call is free.
AN1404 4G Door Station 4 Revision R11 Feb. 2020
Product main features:
1. Stainless-Steel faceplate, Weatherproof.
2. Standalone and Vandal resistant design.
4. Calls up to 3 numbers in sequence.
5. Caller ID access by free call from an authorized phone number (guest).
6. Up to 48 guest numbers can be stored.
7. Can be used for silent monitoring.
8. Ring time/ call time/ relay activate time is adjustable.
9. Relay can be controlled to hold or release the gate.
10. Simple programming via SMS
11. Works with power supplies in the range 12~24VAC/DC.
12. Check dial in and out numbers log via SMS or E-mail
13. Works with mobile phones and land lines.
AN1404 4G DOOR PHONE AND ACCESSORIES
Item
Description
Q’ty
Included
Optional
1
AN1404 –4G Door Station
1
√
2
Power adapter
1
√
3
Operational manual
1
√
4
Surface mounting enclosure
1
√
AN1404 4G Door Station 5 Revision R11 Feb. 2020
INSTALLATION
AN1404 4G Door Station Layout
This4G Door Station is suitable for both flush and surface mounting.
(Front View)
(Side View)
(Rear View)
(Surface Mounting Enclosure)
Speaker
Call Button
Microphone
Antenna
Connector
ANs
AN1404 4G Door Station 6 Revision R11 Feb. 2020
Ensure that there is good network reception at the location where it will be installed
Follow the instructions step by step for installation:
1. Install the surface mounting enclosure by using appropriate fixings on the entrance pillar at
150-160 mm height.
2. Remove security screws from the front panel.
3. Remove the flat cable from the back panel and insert the SIM card.
4. Put the main station unit into the enclosure and fasten it with screws on top and bottom.
5. Connecting the flat cable (BLUE side face up) back to the back panel
6. Fasten the front panel with security screws
Remove
Remove
Screw
Connector
4G door station
Side view
(1)
(2)
(4)
(5)
(3)
(6)
Insert SIM
Screw
AN1404 4G Door Station 7 Revision R11 Feb. 2020
Wiring Diagram
Please follow the wiring instructions carefully.
1. SIM card
Register your SIM card with the network, and check it works in a mobile phone
You MUST remove the PIN code from the SIM before inserting it in the AN1404.
Ensure the power is OFF before inserting the SIM card. Carefully slide the SIM holder in the
OPEN direction, insert the SIM, and slide in the CLOSED direction to lock it in place.
2. Door Lock
Connect an electric door lock to terminals marked “NO or NC & COM as required.
3. Power Supply
- Connect a 12 volt DC power supply to terminals marked “AC, AC”.
- The power supply should be capable of supplying a constant current of no less than 1amp.
- Alternatively, you may use local 12-24 DC or AC power source.
4. After a final check of wiring, switch on the power.
5. Allow 20~30 seconds for the unit to boot up and detect the network. Once a successful
connection has been made, the unit will sound a confirmation tone and the status LED will
begin flashing.
AN1404 4G Door Station 8 Revision R11 Feb. 2020
LED Indicators
(Also see wiring diagram)
1. LED “Door Station Status “ Indicator
LED
Status
Yellow (standby)
0.1sec ON / 2 sec OFF
Yellow (using)
Solid
2. LED ‘Network “Indicator
LED
Status
Green (ready)
1 sec ON/ 1 sec OFF
Green (searching)
Solid
Green (busy)
Solid
3. LED “ Power “ Indicator
LED
Status
Red (power on)
Solid
Red (power off)
Off
AN14044GDoorStationOperation
When the visitor pushes the call button to activate 4G door station, aring tone will be heard from
the Door Station. At the same time, a connection is being established with the phone number that is
stored in the door station. If the first number is busy or has not answered the call can be diverted to
another phone number, (mobile or landline). When the remote phone answers the call from the door
station and converses with the visitor, the door or gate release can be activated by pressing * on the
phone’s keypad. Relay can also be temporarily or permanently switched on or off by pressing #and 1.
To enter system menu:
There are three different modes under the system menu.
1. Monitoring mode ( listening)
2. Access control mode
3. Programming mode
To gain access to the system menu via phone follows these steps:
1. Call the telephone number of the Door Station
2. Wait for the door station to answer and signal by one beep to enter system menu
3. Enter the password of the mode you require.
4. Password correct is one beep, password error is 3 beeps.
5. After 3 failed attempts at the password, the call hangs up.
AN1404 4G Door Station 9 Revision R11 Feb. 2020
Enter Monitoring Mode (listening)
1. Call the telephone number of the 4G door station
2. This device will then verify your phone number with your predefined numbers.
3. You will hear a “Do” tone to enter motoring mode by pressing【*13*1212＃】where 1212
is the password. Then you will be able to listen to door station.
*This feature can also be carried out by sending the same SMS commands
* Under the monitoring mode speaker is OFF. (Press 35＃to turn on speaker)
* You can still press * to active relay under this mode but speaker must be ON status.
AN1404 4G Door Station 10 Revision R11 Feb. 2020
Enter Access Control Mode
1. Call the telephone number of the door station.
2. This device will then verify your phone number with your predefined numbers.
3. You will hear a “Do” tone to enter access control mode by pressing【*33*5678＃】where
5678 is the password.
4. The door will be opened after entering the correct password
*(To open the door by using password, if the number is not stored in the guest list)
Enter Programming Mode
1. Call the telephone number of the door station
2. This device will then verify your phone number with your predefined numbers.
3. You will hear a “Do” tone to enter into programming mode by pressing【*12* 1234＃】
where 1234 is the password.
4. You are now in the “programming mode”
Note: At the end of each command there can be one of the two indications:
Successful: is a long “beep” tone, failed: are three short “beep” tones.
5. To make changes on settings please refer to the user commands.
6. To end programming mode just hang up.
NOTE:
*For less chance of interference during programming, originate the call from a land line, rather than a
mobile, and enter the digits slowly or using programming by text message.
Programming by text message
Programming can be carried out by phone or text message
(Certain programming features can only be set up by text message, refer to user commands)
Programming by text message is the simplest way to customize the settings of the Door Station and to
add or delete guest telephone numbers. Simply send texts in the format to the telephone number of
the SIM within the 4G Door Station.
Note:
1. A Single SMS text messages is limited to 140 characters.
2. You can program many different user command codes in one text message with SMS command
format. *12*1234 # [command Code1] # [command Code 2] # [command Code3] #........
3. Each SMS must start with the pass code , default 1234 in the following format *12*1234 #
Followed immediately by a command.
AN1404 4G Door Station 11 Revision R11 Feb. 2020
4. To program a call button numbers DO NOT enter country code, just the complete number as
you would dial it.
Example:
Program call button phone numbers (Max 3 numbers) and delete 2&3 phone numbers.(Refer to user
commands P.16)
058 57235 (landline number 1)
086 5682554 (mobile number 2)
086 2235644 (mobile number 3)
Command to use: *12*1234#1[Y][X][ phone number] #....
Y= 1~3 (sequence of phone number)
X= 1(to receive audio call)
SMS format: (storing call button phone numbers)
*12*1234#11105857235#1210865682554#1310862235644#
SMS format: (delete 2&3 phone numbers from call button)
*12*1234#12*#13*#
User command code CORRECT example:
SMS format:
*12*1234#11105857235#1220865682554#1310862235644#
SMS reply:
11105857235#1220865682554#1310862235644# OK
User command code ERROR (user command 129error) example:
SMS format:
*12*1234#11105857235#1290865682554#1310862235644#
SMS reply:
1110587235#1290865682554# Error
Programming by phone:
Note: Phone programming can’t be used from phone numbers which are already programmed
to open the door, but you can disable Caller ID display (withhold the number) on the mobile
before using to bypass. (Prefix the number with 1831)
To gain access to the programming mode via phone follows these steps:
AN1404 4G Door Station 12 Revision R11 Feb. 2020
Example:
To program a telephone number for door release by phone
Enter Programming Mode by Pressing…..
*12*1234# (1234 is default password)
A successful pass code will produce a single long beep. A failed attempt will produce 3 short
bleeps.
You may now program up to 48 telephone entry numbers into memory.
Use the following commands to program the unit
* Insert international country code (1~3 digits): 71 [country code] #
* Add a number (up to 48 numbers): 72 [ telephone number] #
* Delete a number: 73 [ telephone number] #
*Delete all numbers: 73*#
Door /Gate Release
This 4G Door Station also has an extra feature to allow user to gain access from their phone
by two methods.
1. by Caller ID recognition
2. by access control password mode
1. Caller ID recognition to open
Ring in to open the door for authorized telephone numbers. It can support for up to 48 users.
When the Door Station receives an incoming call from, it will check the calling number and if the
number is in the guest list, the Door Station will drop the call and then open the gate / door. The
Door Station doesn’t answer the call, it simply checks the caller ID, so this is a free call.
For Caller ID recognition to open the door or gate you need to program the COUNTRY
CODE and mobile numbers into the memory before using.
Example:
Ireland Country code: 353 (UK: 44 / USA: 1)
086 5683624 (1. mobile number)
086 5682554 (2. mobile number)
086 2235644 (3. mobile number)
AN1404 4G Door Station 13 Revision R11 Feb. 2020
Command to use: *12*1234#71[country code]#72[ phone number] #72[ phone number]
#....
SMS format:
*12*1234#71353#720865683624#720865682554#720862235644#
To delete phone numbers of dialing in to open
SMS format: (to delete phone number 1 and 2)
*12*1234#730865683624#730865682554#
SMS format: (to delete all numbers)
*12*1234#73*#
After the numbers are programmed you can send a text message to check the stored numbers
by sending SMS format *21# , then the Door Station will reply with the phone number list text
message.
2. Access control password to open
Dial the SIM card telephone number. The unit will answer the call and you will hear a bleep
tone.
To trigger door by pressing *33*5678#
To latch or hold open door by pressing *34*5678#
To unlatch door by pressing *35*5678#
*This feature can also be carried out by sending the same SMS commands.
TO CHECK SIGNAL STRENGTH: (0~31LEVELS)
When a request for signal strength SMS is sent to the4G Door Station it will reply with a signal
strength code,service provider name and current network (GSM or WCDMA).The signal
strength code will be between 0~31 means the signal level is from poor to best. When the unit
detects the WCDMAnetwork signal is poor will automatically switch to GSM to get better signal.
Example
SMS format: *20#
SMS reply: Vodafone , WCDMA, Signal Level = 31 【Signal is very strong】
AN1404 4G Door Station 14 Revision R11 Feb. 2020
CHECK RELAY & DETECT (INPUT) STATUS:
You can send SMS command code to check relay status and Detect status.( checking door
is opened or closed)
SMS format: *22#
SMS reply: Relay=ON Detect = ON【Relay=Hold, Detect=GND】
Door opening detection
Terminal mark” DET” input” (see wiring diagram P7) is for you to connect a door sensor. The
gate would have a sensor wired through “DET” input to ground. When the door sensor is
triggered, a SMS message “door open alarm”will be sent to the predefined call button phone
numbers.
Panel opening detection –tamper alarm.
A panel opening sensor is built inside the electronic board, once the panel of Door Station has
been removed, the alarm will go off from the speaker and a SMS message “panel open alarm”
is sent to the predefined call button phone numbers.
Administrator Number
Once the administrator’s number is stored in the unit, this is the only number that is allowed to
enter the program mode, either by dialing in, or by text messages.
Example:
Program a mobile number as an administrator number via SMS
Mobile number: 0865682554
Command to use *12*1234#74 [Admin number]#
SMS format *12*1234#740865682554#
To delete theAdmin number *12*1234#74*#
AN1404 4G Door Station 15 Revision R11 Feb. 2020
Check a Log of Dial in and Dial out Numbers via E-mail or SMS
This system allows you to save dial in numbers log and will then automatically send the record via
e-mail or SMS as your request when it reaches 25 numbers in the memory.
There is a list of commands you need and examples to guide you on the settings for this feature.
Please setup following required parameters and commands before you can use it.
NOTE: G-mail doesn’t support this feature.
No.
Function
SMS command codes
1
Way of sending a log of dial in
numbers via e-mail or SMS
*12*1234#84[N]#
N=0 (no saving / no sending record)
N=1 (via SMS, 4 numbers limited /SMS)
N=2(via e-mail, 25 numbers /e-mail )
Sending record via email / command code example: *12*1234#842#
2
GPRS parameters setting
*40*1234#APN, auth_type,user name,paANword#
auth_type: 0= none / 1= PAP / 2= CHAP
Command code
Example:
3
E-mail parameters setting
( Doesn’t support Gmail)
*41*1234#SMTP server,port,user name, paANword,
e-mail addreAN, e-mail sender name#
Command code
Example :
4
Recipient & Carbon copy settings
*42*1234# recipient e-mail addreAN, recipient name,
carbon copy e-mail addreAN, carbon copy name#
AN1404 4G Door Station 16 Revision R11 Feb. 2020
Commande code example:
5
E-mail subject setting
*43*1234# e-mail subject#
Command code Example:
No.
Function
SMS command codes
6
To immediately send current dial in
numbers log via email or SMS
*44*1234#
7
Check parameters setting
*4[N]*1234#
N=0( reply GPRS parameters)
N=1 ( reply e-mail parameters)
N=2 ( reply recipient & carbon copy)
N=3 ( reply e-mail subject)
Check GPRS parameters setting / Command code example: *40*1234#
8
Mobile number for receiving a log of
dial in numbers via SMS
*12*1234#85[mobile Number]#
9
Delete mobile number for receiving a
log of dial in numbers via SMS
*12*1234#85*#
10
SIM phone number used in door
station for Clock date and time
correction
*12*1234#86[SIM phone number used in door station]#
11
To delete SIM phone number used in
door station for Clock date and time
correction
*12*1234#86*#
Note: why you need to setup the phone number for system time and date calibration?
This device has a time clock and supports automatically updating their date and time via NITZ
information from network. In case some of the networks are not available for NITZ information that we
strongly suggest to setup date and time calibration. When the device detects NITZ information is not
available from the network will automatically send a command to itself via the SIM card used in the
AN1404 4G Door Station 17 Revision R11 Feb. 2020
door station for time calibration which will keep your “dial in numbers log”with correct date and
time.
Log example:
Ｉ: dial in number / Ｏ: dial out number
How to program checking the log of dial in numbers via SMS
There are 3 programming codes you will need to make this feature work
You can program many different user command codes in a single text message with SMS command
format. *12*1234 # [command Code1] # [command Code 2] # [command Code3] #........
Example:
Mobile number for receiving a log 0907967223
SIM phone number used in the 4G door station
0948778458
*12*1234#841#850907967223#860948778458#
Send *44*1234# to check log
Replied log information via SMS example:
AN1404 4G Door Station 18 Revision R11 Feb. 2020
I: Dial IN numbers
N:Next text massage
E: End text message
User Commands
To gain access to the different modes and control relay (via dial in)
No.
Function
Command
Description
Default
1
Enter Programming Mode
*12* [ password ] #
To enter system for programming
1234
2
Enter Monitoring Mode
*13* [ password ] #
To hear the surroundings where the 4G
door station is installed
1212
3
Enter Access control
Mode (Trigger relay)
*33* [ password ] #
Access control password mode
5678
4
Hold Relay
*34* [ password ] #
To hold relay to keep door opened
5678
5
Release Relay
*35* [ password ] #
To release relay for door close
5678
User commands to check system info & control relay via SMS
No.
Function
Command
Reply
1
Check signal strength
*20#
Signal Level 0~31( from poor to best)
Service provider name, network
2
Check stored numbers
*21#
O [ number]…I [ number]…..E (N)
O：call button numbers list
I ：dial in to open numbers list
E：End
N：Next SMS
AN1404 4G Door Station 19 Revision R11 Feb. 2020
3
Check relay status
*22#
Relay [status], Detect [status]
Status= ON / OFF
4
Trigger relay
*33* [ password ] #
No reply (default paANword:5678)
(Latch on when relay is on hold status)
5
Hold relay
*34* [ password ] #
No reply
(default paANword:5678)
6
Release relay
*35* [ password ] #
No reply
(default paANword:5678)
●SMS data error
(Only 0~9、*、# are available)
SMS Data Error
●Function code error
Function Code Error
User commands table
You can program many different user command codes in one text meANage with SMS command
format. *12*1234 # [command Code1] # [command Code 2] # [command Code3] #........
No.
Feature
Command
Description
Default
1
Change password of
Programming Mode
01 [new password ] #
Password= 4 digit codes
1234
2
Change password of Access
control Mode
02 [new password] #
Password= 4 digit codes
5678
3
Change password of
Monitoring Mode
03 [new password ] #
Password= 4 digit codes
1212
4
Store a call button phone
number
1 [ Y][X][ phone number] #
Y=1~3 (sequence of phone
number)
X=1 (audio call)
Max 3 phone numbers
None
5
Delete a call button
Phone number
1 [Y] *#
Y=1~3 (sequence of phone
number)
None
6
Speaker Volume
3 [ speaker volume] #
Volume= 0~4 levels
3
7
Microphone Volume
4 [ microphone volume] #
Volume= 0~4 levels
3
8
Relay Activate Time
51 [ relay activate time] #
Relay activate time= 1~9999 sec
1 sec
9
Divert to second no. time
52 [ divert time] #
divert time= 10~99 sec
(2 digit codes)
20 sec
10
Call Time
53 [call time] #
call time= 005~999 sec
(3 digit codes)
060 sec
11
Monitoring duration time
55 [time] #
Time= 00~60 minutes
10 mins
AN1404 4G Door Station 20 Revision R11 Feb. 2020
00 ( no limit)
12
Change trigger relay code
61 [ code ] #
code= 0,1,2,3,5,7,8,9 / * /＃
*
13
Change hold relay code
63 [code ] #
code= 0,1,2,3,5,7,8,9 / * /＃
#
14
Change release relay code
64 [ code ] #
code= 0,1,2,3,5,7,8,9 / * /＃
1
15
Add ring tone after the
phone is answered while
waiting on making call
66 [ring tone ]#
Ring tone =0~9 tones
0
16
Ring in to open the door
(Max: 48 numbers)
71 [ country code ] #
72 [ Add a phone number] #
73 [ Del a phone number ] #
73*#
Country code =1~3 digit codes
Add a number = 3~15 digit codes
Del a number = 3~15 digit codes
Del all phone numbers
886
17
Add administrator phone
number
74 [ admin number] #
admin number= 3~15 digit codes
( no number no restriction)
None
18
Delete administrator
phone number
74*#
delete administrator phone
number
None
19
Door opening detection
81 [ X ] #
X= 0, 1 , 2
0: OFF / 1: GND
2: EOL (10Kohm)
Off
20
Panel opening alarm
82 [ X ] #
X= 1 , 2
1: alarm / 2: SMS & alarm
alarm
21
Reset
999#
reset default
None
How To Reset The Hardware When You Forget your Password
Warning :
For passwords, do not use two or more of the same number as successive digits .
EG. 11, 00, 112, 122, 88 are not recommended as echo cancellation network software
may cancel the second same digit if entered quickly.
Use passwords like 89, 12 , 23 , 56, 14, 123, 369 , 789 etc without repeating the same
digit numbers.
Table of contents
