Vanderbilt ACTpro EM1030 User manual

ACTpro Readers
Installation Guide
Document ID: A-100505
Edition date: 31.05.2018

Data and design subject to change without notice. / Supply subject to availability.
© 2018 Copyright by Vanderbilt International Ltd.
We reserve all rights in this document and in the subject thereof. By acceptance of the document the recipient acknowledges these rights and
undertakes not to publish the document nor the subject thereof in full or in part, nor to make them available to any third party without our prior
express written authorization, nor to use it for any purpose other than for which it was delivered to him.
Hereby, Vanderbilt International (IRL) Ltd declares that this equipment type is in compliance with the following EU Directives for CE marking:
• Directive 2014/30/EU (Electromagnetic Compatibility Directive)
• Directive 2014/53/EU (Radio Equipment Directive)
• Directive 2011/65/EU (Restriction of the use of certain hazardous substances Directive)
The full text of the EU declaration of conformity is available at: http://van.fyi?Link=DoC
DA
DE
EN
ES
FR
IT
SV
&
http://van.fyi/?Link=ACTpro_Readers

Table of Contents
1 Overview 4
1.1 Product description 4
1.2 Technical specification 4
1.3 Reader connections 5
1.3.1 ACTpro EM1040/EM1050/EM1060 5
1.3.2 ACTpro EM1030 6
1.3.3 CAT5/6 colour code 6
1.4 Wiring for ACTpro 7
1.4.1 Clock & Data entry reader 7
1.4.2 Clock & Data exit reader 7
1.4.3 Wiegand entry reader 8
1.4.4 Wiegand exit reader 8
2 Mounting instructions 9
2.1 EM1030 9
2.2 EM1040/ EM1050/ EM1060 9
2.2.1 Surface mount 9
2.2.2 Flush mount 10
2.2.3 Flush mount to UK pattress box 10
© Vanderbilt 2018 3 A-100505
31.05.2018

1 Overview
This guide describes the following products:
lEM1030 ACTpro Mullion Reader
lEM1040 ACTpro Reader
lEM1050 ACTpro Reader with keypad
lEM1060 ACTpro keypad
1.1 Product description
ACTpro RFID readers are 125Khz readers that support all ACT RFID cards and fobs and HID-compatible
tokens.
lCompatible with Vanderbilt RFID cards and fobs.
lCompatible with HID Clock and Data and Wiegand cards/fobs.
lFeatures a buzzer and an LED indication.
lCan be configured for Wiegand or Clock and Data output.
lCompatible with all standard access control systems.
1.2 Technical specification
EM1030 EM1040 EM1050 EM1060
Connections Pigtail 3 M Terminal Block Terminal Block Terminal Block
Dimensions
W x H x D 37 x 120 x 15mm 95 x 128 x 19mm 95 x 128 x 21mm 95 x 128 x 21mm
Mounting Mullion Flush or Surface Flush or Surface Flush or Surface
Weight 50g 142g 155g 155g
Power Supply 5V DC – 12V DC 5V DC – 12V DC 5V DC – 12V DC 5V DC – 12V DC
Current
Consumption 75mA 75mA 100mA 75mA
Operating
Temperature -40°C to +50°C -40°C to +50°C -40°C to +50°C -40°C to +50°C
Transmit
Frequency 125Khz 125Khz 125Khz NA
Keypad No No Yes Yes
Environmental
Rating IP67 IP67 IP67 IP67
Cable Distance 100m 100m 100m 100m
Output Formats Wiegand or Clock &
Data
Wiegand or Clock &
Data
Wiegand or Clock &
Data
Wiegand or Clock &
Data
© Vanderbilt 2018 4 A-100505
31.05.2018

EM1030 EM1040 EM1050 EM1060
Indoor & Outdoor Yes Yes Yes Yes
Card & PIN Proximity only Proximity only Proximity & PIN PIN only
Standards CE Certified CE Certified CE Certified CE Certified
IMPORTANT:
ACTpro readers must be powered from a fused DC PSU (5-12V, 1A maximum).
If the ACTpro reader is used in a manner not specified in this document, the protection provided by the
reader may be impaired.
1.3 Reader connections
1.3.1 ACTpro EM1040/EM1050/EM1060
15-12V DC 60V/GND
2Data/D0 7RED LED
3CLOCK/D1 8GREEN LED
4SENSE 9BUZZ CTRL
5
EM1050/EM1060 Backlight
Select
Top PINS = Backlight On
Bottom PINS = Backlight Off
ACTpro Readers – Installation Guide Overview
© Vanderbilt 2018 5 A-100505
31.05.2018

1.3.2 ACTpro EM1030
EM1030 is supplied with 3m pigtail cable.
ASENSE (White) FRED LED (Brown)
BCLOCK/D1 (Green) GGREEN LED (Yellow)
CDATA/D0 (Blue) HBuzzer (Orange)
D+12V (Red)
E0V/GND (Black)
1.3.3 CAT5/6 colour code
The following is the suggested colour coding if using CAT5 or CAT6 cabling.
Reader Output Colour
Sense White/Green
Clock / D1 Green
Data / D0 Blue
+12V Orange
(0V) GND White/Orange
Red LED Brown
Green LED White/Brown
ACTpro Readers – Installation Guide Overview
© Vanderbilt 2018 6 A-100505
31.05.2018

1.4 Wiring for ACTpro
Note: Illustrations apply to all ACTpro Readers.
1.4.1 Clock & Data entry reader
ABuzzer input E+12V (Red)
BSENSE (White) F0V / GND (Black)
CCLOCK / D1 (Green) GRED (Brown)
DDATA / D0 (Blue) HGREEN (Yellow)
1.4.2 Clock & Data exit reader
ABuzzer input E+12V (Red)
BSENSE (White) – DO NOT CONNECT SENSE F0V / GND (Black)
CCLOCK / D1 (Green) GRED (Brown)
DDATA / D0 (Blue) HGREEN (Yellow)
ACTpro Readers – Installation Guide Overview
© Vanderbilt 2018 7 A-100505
31.05.2018

1.4.3 Wiegand entry reader
IMPORTANT: To put ACTpro readers into Wiegand, mode connect the SENSE on the reader to
0V/GND.
ABuzzer input E+12V (Red)
BSENSE F0V / GND (Black, White)
CCLOCK / D1 (Green) GRED (Brown)
DDATA / D0 (Blue) HGREEN (Yellow)
1.4.4 Wiegand exit reader
IMPORTANT: To put ACTpro E readers into Wiegand mode, connect the SENSE on the reader to
0V/GND PIN and DATA/D0 to the SENSE PIN on the controller.
ABuzzer input E+12V (Red)
BSENSE (Blue) F0V / GND (Black, White)
CCLOCK / D1 (Green) GRED (Brown)
DDATA / D0 HGREEN (Yellow)
ACTpro Readers – Installation Guide Overview
© Vanderbilt 2018 8 A-100505
31.05.2018

2 Mounting instructions
2.1 EM1030
Screw unit to the surface. Place caps on to the unit and push firmly into place.
2.2 EM1040/ EM1050/ EM1060
2.2.1 Surface mount
AMount the surface mount collar on the wall using the fixing kit supplied in the box.
BPlace the reader/keypad onto the surface mount collar and clip down into place.
CUse the security screw supplied to attached the unit to the surface mount collar.
DPlace the cap onto the unit and push firmly in place.
© Vanderbilt 2018 9 A-100505
31.05.2018

2.2.2 Flush mount
ARemove spacers before mounting.
BPrepare the mounting surface to receive sub-surface terminals.
Mount the flush mount collar on the wall using the fixing kit supplied in the box.
CPlace the reader/keypad onto the surface mount collar and clip down into place.
DUse the security screw supplied to attached the unit to the flush mount collar.
EPlace the cap onto the unit and push firmly in place.
2.2.3 Flush mount to UK pattress box
Spacers break away from the main component when required by installer for use.
Determine the distance between the patress box and the mounting plate using the spacers. The spacers
are labelled 1mm to 4mm. A spacer of the correct length is assembled by stacking the spacers together.
View A shows mounting plate before spacers are broken away by installer.
View B shows spacer stacking.
ACTpro Readers – Installation Guide Mounting instructions
© Vanderbilt 2018 10 A-100505
31.05.2018