Ovation E-160WW User manual

User Manual

Ovation E-160WW User Manual Rev. 1
EDITION NOTES
The Ovation E-160WW User Manual includes a description, safety precautions, installation, programming,
operation and maintenance instructions for the Ovation E-160WW as of the release of this edition.
Trademarks
CHAUVET, the Chauvet logo and Ovation E-160WW are registered trademarks or trademarks of Chauvet
& Sons, LLC (d/b/a Chauvet and Chauvet Lighting) in the United States and other countries. Other
company and product names and logos referred to herein may be trademarks of their respective
companies.
Copyright Notice
The works of authorship contained in this manual, including, but not limited to, all design, text and images
are owned by Chauvet.
© Copyright 2017 Chauvet & Sons, LLC. All rights reserved.
Electronically published by Chauvet in the United States of America.
Manual Use
Chauvet authorizes its customers to download and print this manual for professional information purposes
only. Chauvet expressly prohibits the usage, copy, storage, distribution, modification, or printing of this
manual or its content for any other purpose without written consent from Chauvet.
Document Printing
For best results, print this document in color, on letter size paper (8.5 x 11 in), double-sided. If using A4
paper (210 x 297 mm), configure the printer to scale the content accordingly.
Intended Audience
Any person installing, operating, and/or maintaining this product should completely read through the guide
that shipped with the product, as well as this manual, before installing, operating, or maintaining this
product.
Disclaimer
Chauvet believes that the information contained in this manual is accurate in all respects. However,
Chauvet assumes no responsibility and specifically disclaims any and all liability to any party for any loss,
damage or disruption caused by any errors or omissions in this document, whether such errors or
omissions result from negligence, accident or any other cause. Chauvet reserves the right to revise the
content of this document without any obligation to notify any person or company of such revision, however,
Chauvet has no obligation to make, and does not commit to make, any such revisions. Download the latest
version from www.chauvetprofessional.com
Document Revision
This Ovation E-160WW User Manual is the 1st edition of this document. Go to
www.chauvetprofessional.com for the latest version.

Ovation E-160WW User Manual Rev. 1
TABLE OF CONTENTS
TOC 1 of 2
TABLE OF CONTENTS
1. Before You Begin ....................................................................... 3
What Is Included ........................................................................................... 3
Claims........................................................................................................... 3
Manual Conventions ..................................................................................... 3
Symbols ........................................................................................................ 3
Safety Notes.................................................................................................. 4
Personal Safety.............................................................................................................. 4
Mounting and Rigging.................................................................................................... 4
Power and Wiring........................................................................................................... 4
Operation ...................................................................................................... 4
Expected LED Lifespan................................................................................. 4
2. Introduction ................................................................................ 5
Description.................................................................................................... 5
Features........................................................................................................ 5
Product Overview.......................................................................................... 6
Product Dimensions...................................................................................... 7
3. Setup ........................................................................................... 8
AC Power...................................................................................................... 8
AC Plug.......................................................................................................................... 8
Power Linking................................................................................................................. 8
Fuse Replacement......................................................................................................... 8
DMX Linking.................................................................................................. 8
DMX Personalities.......................................................................................................... 8
Remote Device Management........................................................................ 9
Master/Slave Connectivity.............................................................................................. 9
Mounting ....................................................................................................... 9
Orientation...................................................................................................................... 9
Rigging........................................................................................................................... 9
Procedure....................................................................................................................... 10
Manual Beam Focus Control......................................................................... 10
Rotating the Barrel Assembly........................................................................ 11
Accessory Slot .............................................................................................. 11
4. Operation .................................................................................... 12
Control Panel Operation................................................................................ 12
Control Options............................................................................................. 12
Programming................................................................................................. 12
Menu Map..................................................................................................... 12
Configuration (Standalone)........................................................................... 13
Static Mode.................................................................................................................... 13
Focus Mode ................................................................................................................... 13
Auto Programs............................................................................................................... 13
Master/Slave.................................................................................................................. 13
Dimmer Profiles.............................................................................................................. 14
LED Frequency.............................................................................................................. 14
Fan Mode....................................................................................................................... 14
Back Light ...................................................................................................................... 14
System Information........................................................................................................ 14
Configuration (DMX) ..................................................................................... 14
DMX Personalities.......................................................................................................... 14
DMX Control................................................................................................................... 15
DMX Values.................................................................................................. 15

TABLE OF CONTENTS
Ovation E-160WW User Manual Rev. 1
TOC 2 of 2
6 Ch................................................................................................................................ 15
3 Ch................................................................................................................................ 15
2 Ch................................................................................................................................ 15
1 Ch................................................................................................................................ 15
5. Technical Information................................................................ 16
Product Maintenance.................................................................................... 16
6. Technical Specifications ........................................................... 17
7. Returns ........................................................................................ 18
7. Contact Us .................................................................................. 19

Page 3 of 19
Ovation E-160WW User Manual Rev. 1
BEFORE YOU BEGIN
1. BEFORE YOU BEGIN
What Is Included
Claims
Carefully unpack the product immediately and check the container to make sure all the parts are in the
package and are in good condition.
If the box or the contents (the product and included accessories) appear damaged from shipping, or show
signs of mishandling, notify the carrier immediately, not Chauvet. Failure to report damage to the carrier
immediately may invalidate your claim. In addition, keep the box and contents for inspection.
For other issues, such as missing components or parts, damage not related to shipping, or concealed
damage, file a claim with Chauvet within 7 days of delivery.
Manual Conventions
Symbols
• Ovation E-160WW
• Power Cord • Warranty Card • Quick Reference Guide
Convention Meaning
1–512 A range of values
50/60 A set of values of which only one can be chosen
<SET> A button on the product’s control panel
Settings A product function or a menu option
Symbol Meaning
Electrical warning. Not following these instructions may cause electrical damage to
the product, accessories, or the user.
Critical installation, configuration, or operation information. Not following these
instructions may make the product not work, cause damage to the product, or cause
harm to the operator.
Important installation or configuration information. The product may not function
correctly if this information is not used.
Useful information.
Any reference to data or power connections in this manual assumes the use of
Seetronic IP rated cables.
The term “DMX” used throughout this manual refers to the USITT DMX512-A
digital data transmission protocol.
!
!

Page 4 of 19
BEFORE YOU BEGIN
Ovation E-160WW User Manual Rev. 1
Safety Notes
Read all the following safety notes before working with this product. These notes contain important
information about the installation, usage, and maintenance of this product.
Personal Safety
• Avoid direct eye exposure to the light source while the product is on.
• Always disconnect the product from the power source before cleaning or replacing the fuse.
• Always connect the product to a grounded circuit to avoid the risk of electrocution.
• Do not touch the product’s housing when operating because it may be very hot.
Mounting and Rigging
• This product is for indoor use only! To prevent risk of fire or shock, do not expose this product to
rain or moisture. (IP20)
• CAUTION:Whentransferring product from extremetemperatureenvironments,(e.g., cold truck towarm,
humid ballroom) condensation may form on the internal electronics of the product. To avoid causing a
failure, allow product to fully acclimate to the surrounding environment before connecting it to power.
• Mount this product in a location with adequate ventilation, at least 20 in (50 cm) from adjacent
surfaces.
• Make sure there are no flammable materials close to the product when operating.
• When hanging this product, always secure to a fastening device using a safety cable.
• Use caution when loosening the barrel rotation knobs. If these knobs become too loose, the barrel
assembly may inadvertently separate from the light engine.
Power and Wiring
• Always make sure you are connecting the product to the proper voltage in accordance with the
specifications in this manual or on the product’s specification label.
• Never connect the product to a dimmer pack or rheostat.
• To eliminate unnecessary wear and improve its lifespan, during periods of non-use completely
disconnect the product from power via breaker or by unplugging it.
• Never connect this product to a dimmer pack or rheostat
• Never disconnect this product by pulling or tugging on the power cable.
Operation
• Donotoperatethisproduct if there is damage onthehousing,lenses,or cables. Have the damaged
parts replaced by an authorized technician at once.
• Do not cover the ventilation slots when operating to avoid internal overheating.
• The maximum ambient temperature is 113 °F (45 °C). Do not operate the product at higher temperatures.
• In the event of a serious operation problem, stop using this product immediately!
Expected LED Lifespan
LEDs gradually decline in brightness over time, primarily because of heat. LEDs that are arranged in
clusters experience higher operating temperatures than single LEDs. For this reason, operating clustered
LEDs at their fullest intensity significantly reduces the LEDs’ lifespan. Under normal conditions, this
lifespan is 40,000 to 50,000 hours. If extending this lifespan is vital, lower the operating temperature by
improving the ventilation around the product, thus reducing the ambient temperature. In addition, limiting
the overall projection intensity may extend the LEDs’ lifespan.
This product contains no user-serviceable parts. Any reference to servicing in
this User Manual will only apply to properly trained, certified technicians. Do not
open the housing or attempt any repairs.
All applicable local codes and regulations apply to proper installation of this
product.
If your Chauvet product requires service, contact Chauvet Technical Support.
!

Page 5 of 19
Ovation E-160WW User Manual Rev. 1
INTRODUCTION
2. INTRODUCTION
Description
The Ovation E-160WW delivers an excellent white light with a warm color temperature and a beautiful flat
field. It also features standard beam shaping shutters, a gobo/effect slot and lens barrels that are
interchangeable with other popular ERS fixtures. Selectable dimming curves ensure smooth fading cues
that intermix well with the output of conventional theatre ellipsoidals.
Features
• Warm white LED ERS-style lighting product
• Operating modes:
• 1-channel: dimmer control
• 2-channel: dimmer and fine dimmer control
• 3-channel: dimmer, fine dimmer, and strobe control
• 6-channel: dimmer, fine dimmer, strobe control, auto programs, auto speed, and dimmer mode
• Warm white ERS style fixture with output similar to a tungsten 575 W source
• Draws less than 100 W of power, a true electrical bill reducing fixture!
• Ultra smooth 16-bit dimming, and 8-bit dimming curves to complement any lighting scheme.
• Flat, even field of light for superior gobo projection
• RDM (Remote Device Management) for added flexibility
• Adjustable PWM (Pulse Width Modulation) to avoid flickering on camera
• Virtually silent operation for use in studio and theatre applications

Page 6 of 19
INTRODUCTION
Ovation E-160WW User Manual Rev. 1
Product Overview
Light
Engine
Barrel
Rotation
Knobs
Pattern Holder Slot
(A-size holder for 3-in
patterns B-size holder for
2.5-in and 2.75-in
patterns, sold separately)
Accessory Slot
Beam Focus
Knobs
Gel Frame
Holder
Barrel
Assembly Lens Tube
(Sold Separately)
Framing
Shutter
(x4)
Handle
Menu
Buttons
FuseHolder
powerCON®
Input
powerCON®
Output
Display
3- and 5- pin
DMX In
3- and 5- pin
DMX Out

Page 7 of 19
Ovation E-160WW User Manual Rev. 1
INTRODUCTION
Product Dimensions
9.33 in
237 mm
13.46 in
342 mm
19.92 in
506 mm
25.71 in
653 mm
6.97 in
177 mm
12.56 in
319 mm
6.85 in
174 mm
6.30 in
160 mm
27.95 in
710 mm

Page 8 of 19
SETUP
Ovation E-160WW User Manual Rev. 1
3. SETUP
AC Power
Each Ovation E-160WW has an auto-ranging power supply that works with an input voltage range of 100
to 240 VAC, 50/60 Hz. To determine the power requirements for each Ovation E-160WW, refer to the label
affixed to the product. You can also refer to the Technical Specifications chart in this manual.
The listed current rating indicates the maximum current draw during normal operation. For more
information, download Sizing Circuit Breakers from the Chauvet website: www.chauvetprofessional.com.
.
AC Plug
The Ovation E-160WW comes with a power input cord terminated with a Seetronic Powerkon A connector
on one end and an Edison plug on the other end (U.S. market). If the power input cord that came with your
product has no plug, or if you need the change the plug, use the table below to wire the new plug.
Power Linking
The product supports power linking. You can power link up to 15 products at 120 V; up to 26 at 208 V; or up
to 28 at 230 V. This product comes with a power input cord. Power linking cables are available from
Chauvet for purchase.
Fuse Replacement
The product supports power linking. You can power link up to 15 products at 120 V; up to 26 at 208 V; or up
to 28 at 230 V. This product comes with a power input cord. Power linking cables are available from
Chauvet for purchase.
DMX Linking
You can link the Ovation E-160WW to a DMX controller using a 3- or 5-pin DMX connection. If using other
DMX-compatible products with this product, you can control each individually with a single DMX controller.
DMX Personalities
The Ovation E-160WW uses a 3- or 5-pin DMX data connection for the 1-, 2-, 3- and 6-channel DMX
personalities.
• Refer to the Introduction for a brief description of each DMX personality.
• Refer to the Operation chapter to learn how to configure the Ovation E-160WW to work in these
personalities.
• The DMX Values section provides detailed information regarding the DMX personalities.
• Always connect the product to a protected circuit (circuit breaker or fuse). Make
sure the product has an appropriate electrical ground to avoid the risk of
electrocution or fire.
• To eliminate unnecessary wear and improve its lifespan, during periods of non-
use completely disconnect the product from power via breaker or by unplugging
it.
Never connect the product to a rheostat (variable resistor) or dimmer circuit, even if
the rheostat or dimmer channel serves only as a 0 to 100% switch.
Connection Wire (U.S.) Wire (Europe) Screw Color
AC Live Black Brown Yellow or Brass
AC Neutral White Blue Silver
AC Ground Green/Yellow Green/Yellow Green
If you are not familiar with or need more information about DMX standards,
Master/Slave connectivity, or the DMX cables needed to link this product to a
DMX controller, download the DMX Primer from the Chauvet website:
www.chauvetprofessional.com.
!

Page 9 of 19
Ovation E-160WW User Manual Rev. 1
SETUP
Remote Device Management
Remote Device Management, or RDM, is a standard for allowing DMX-enabled devices to communicate
bi-directionally along existing DMX cabling. Check the DMX controller’s User Manual or with the
manufacturer as not all DMX controllers have this capability. The Ovation E-260WW supports RDM
protocol that allows feedback to make changes to menu map options.
Master/Slave Connectivity
The Master/Slave mode allows an Ovation E-160WW (the master) to control one or more Ovation E-
160WW products (the slaves) without a DMX controller. One Ovation E-160WW becomes the master
when running an auto or custom program, or by being in a Static mode.
You must configure each slave’s control panel to operate in Slave mode. During Master/Slave operation,
the slaves will operate in unison with the master.
Mounting
Before mounting the product, read and follow the safety recommendations indicated in the Safety Notes.
For our CHAUVET Professional line of mounting clamps, go to http://trusst.com/products/.
Orientation
Always mount this product in a safe position, making sure there is adequate room for ventilation,
configuration, and maintenance.
Rigging
Chauvet recommends using the following general guidelines when mounting this product.
• Before deciding on a location for the product, make sure there is easy access to the product for
maintenance and programming purposes.
• Make sure that the structure onto which you are mounting the product can support the product’s
weight. See the Technical Specifications for weight information.
• When mounting the product overhead, always use a safety cable. Mount the product securely to a
rigging point, whether an elevated platform or a truss.
• When rigging the product onto a truss, use a mounting clamp of appropriate weight capacity.
• When power linking multiple products, mount the products close enough for power linking cables to
reach.
• The bracket adjustment knobs allow for directional adjustment when aiming the product to the
desired angle. Only loosen or tighten the bracket knobs manually. Using tools could damage the
knobs.
DO NOT connect a DMX controller to products operating in Master/Slave mode. The
DMX controller signals may interfere with the signals from the master.
• The Operation section of this manual provides detailed instructions on how
to configure the master and slaves.
• Ifyou are notfamiliar with,or needmore information about, DMX standards,
or the DMX cables needed to link this product to a DMX controller,
download the DMX Primer from the Chauvet website:
www.chauvetprofessional.com.

Page 10 of 19
SETUP
Ovation E-160WW User Manual Rev. 1
Manual Beam Focus Control
The Ovation E-160WW has a manual focus, which is adjusted as follows:
1. Locate the beam focus knobs at the top and bottom of the barrel assembly
2. Loosen the knobs by turning them counter-clockwise.
3. Slide the lens tube forward or backward until you achieve the desired focus or beam edge.
4. Tighten the knobs by turning them clockwise, which lock the lens tube’s position.
To avoid changing menu settings while focusing the Ovation E-260WW, press and
hold the <ENTER> button for 3 seconds. This will put the product in “Focus Mode”
by increasing the intensity to 100%. To exit out of focus mode, press <MENU>.
Procedure
The Ovation E-160WW comes with a hanging/mounting bracket to which you can attach mounting clamps.
The bracket has 13-mm holes, for this purpose. You must supply your own mounting clamps, so be sure
the clamps are capable of supporting the weight of this product. Use at least one mounting point per
product where necessary. For the CHAUVET Professional line of mounting clamps, go to http://
www.trusst.com/products.
Mounting Diagram
Mounting Clamp
(such as CLP-15 or CLP-15N
from Chauvet)
Safety Cable
(such as CH-05 from
Chauvet)
Mounting Bracket
Bracket
Adjustment hand
Shank
Alternative Yoke
Attachment
Overhead
Mounting Alternate
Short
Mounting

Page 11 of 19
Ovation E-160WW User Manual Rev. 1
SETUP
Rotating the Barrel Assembly
The Ovation E-160WW allows manual rotation of the barrel assembly, as follows.
1. Locate the barrel rotation knobs at the top and bottom of the light engine.
2. Loosen the knobs by turning them counter-clockwise.
•Note: Do not remove the knobs.
3. Rotate the barrel to the desired position, up to 25° in either direction from the centered position.
4. Tighten the knobs by turning them clockwise, which lock the barrel’s position.
Accessory Slot
The Ovation E-160WW has an accessory slot, which holds a drop-in iris, a motorized pattern device, or
various other optional accessories (sold separately).
1. Loosen the thumbscrews on the slot cover.
•Note: Do not remove the thumbscrews.
2. Slide to cover forward.
3. Insert an accessory.
•Note: Make sure to insert the accessory correctly. For example, make sure the iris handle
extends upward from the slot.
4. Slide the cover back. Make sure any handles or adjustment tools that stick out the top are able to
function correctly.
5. Tighten the thumbscrews to secure the cover.
Make sure the barrel assembly is oriented with the pattern holder and accessory
slots at the top of the product.
Make sure the barrel assembly is oriented with the pattern holder and accessory
slots at the top of the product.
Thumbscrews
Iris Handle
Accessory Slot
Cover
Barrel
Assembly Drop-in Iris

Page 12 of 19
OPERATION
Ovation E-160WW User Manual Rev. 1
4. OPERATION
Control Panel Operation
Control Options
Set the Ovation E-160WW starting address in the 001-512 DMX range. This enables control of up to 46
products in the 6-channel 6CH personality.
Programming
Refer to the Menu Map to understand the menu options. The menu map shows the main level and a
variable number of programming levels for each option.
• To go to the desired main level, press <MENU> repeatedly until the option shows on the display.
Press <ENTER> to select. This will take you to the first programming level for that option.
• To select an option or value within the current programming level, press <UP> or <DOWN> until
the option shows on the display. Press <ENTER> to select. In this case, if there is another
programming level, you will see that first option, or you will see the selected value.
• Press <MENU> repeatedly to exit to the previous main level.
Menu Map
Button Function
<MENU> Exits from the current menu or function
<ENTER> Enables the currently displayed menu or sets the currently selected value in to the
current function
<UP> Navigates upward through the menu list or increases the numeric value when in a
function
<DOWN> Navigates downward through the menu list or decreases the numeric value when in a
function
Main Level Programming Levels Description
DMX Address 001–512 Selects DMX address (highest channel restricted to
personality chosen).
DMX Channel
1 Ch 1-channel: dimmer
2 Ch 2-channel: 16-bit dimmer
3 Ch 3-channel: 16-bit dimmer, strobe
6 Ch 6-channel: 16-bit dimmer, strobe, auto programs,
auto speed, dimmer mode
Static Dimmer 0–255 Sets the intensity of the light output
Strobe Sets the strobe rate
Auto Show
Auto 1
1–100 Selects automatic programs and speed
Auto 2
Auto 3
Auto 4
Master/Slave
Mode Master Master mode
Slave DMX slave mode
Dimmer Mode Off Linear dimming
Dimmer 1–3 Dimming curves: Dimmer 1 (fast) to Dimmer 3
(slow)
LED
Frequency
600Hz
PWM frequency
1200Hz
2000Hz
4000Hz
6000Hz
25KHz

Page 13 of 19
Ovation E-160WW User Manual Rev. 1
OPERATION
Configuration (Standalone)
Use standalone configuration to operate the product without a DMX controller.
Static Mode
The Static mode allows for permanent dimmer and strobe presets without a DMX controller.
1. Go to the Static main level.
2. Select Dimmer (for intensity control) or Strobe (For Strobe Rate).
3. Select the desired value (0–255).
Focus Mode
Focus mode allows for focusing of the Ovation E-160WW without changing any menu settings.
1. Press and hold <ENTER> for 3 seconds. The intensity will increase to 100%.
2. Press <MENU> to exit to previous settings.
Auto Programs
Auto programs allow for dynamic blinder effects without a DMX controller.
1. Go to the Auto Show main level
2. Select the desired auto (Auto 1–4).
3. Select the desired speed (1–100).
Master/Slave
The Master/Slave mode allows a group of Ovation E-160WW products (the slaves) to simultaneously
duplicate the output of another Ovation E-160WW (the master) without a DMX controller.
To set each of the slaves:
1. Go to the Master/Slave main level
2. Select Slave.
To set the master:
1. Go to the Master/Slave main level
2. Select Master.
3. Select an auto program as explained in Auto Programs, or a static setting.
Fan Mode Auto Fan speed based on product temperature
On Fan always at maximum
Back Light
On Display backlight always on
10S Turns off display backlight after 10 sec of inactivity
20S Turns off display backlight after 20 sec of inactivity
30S Turns off display backlight after 30 sec of inactivity
Information Fixture Hours <_ _ _ _H> Shows total product hours Version <V_._> Shows installed software version
UID ___ ___ _ ___ __ Shows product ID
The auto programs cannot be edited.
• The master is the one that runs a program whether in Auto or Static mode.
• Do not connect a DMX controller to the products configured for Master/Slave
operation. The DMX controller may interfere with signals from the master.
• The master should be the first product in the daisy chain.
Main Level Programming Levels Description

Page 14 of 19
OPERATION
Ovation E-160WW User Manual Rev. 1
Dimmer Profiles
This setting determines how fast the output of the Ovation E-160WW changes when you modify the output
value. This setting provides four different options to simulate the dimming curve of an incandescent lighting
product.
• Go to the Dimmer Mode main level.
• Select a dimmer curve (OFF, Dimmer 1, Dimmer 2, or Dimmer 3).
LED Frequency
This option changes the Pulse Width Modulation (PWM) frequency of the LEDs on the Ovation E-160WW.
1. Go to the LED Frequency main level.
2. Select PWM Frequency (600Hz, 1200Hz,2000Hz,4000Hz, 6000Hz, or 25Khz).
Fan Mode
This setting determines how the fan speed on the Ovation E-160WW is set.
1. Go to the Fan Mode main level
2. Select Auto (fan speed will increase or decrease based on product temperature) or On (fan
speed will always be at maximum).
Back Light
This setting allows for selection of the amount of time the backlight on the Ovation E-160WW’s display
stays on after the last button is pressed on the control panel.
1. Go to the Back Light main level.
2. Select On (remains on), 10S (10 seconds), 20S (20 seconds), or 30S (seconds).
System Information
This option displays the total number of hours the product has run, the installed software version, and the
product’s UID.
1. Go to the Information main level.
2. Select Fixture Hours, Version, or UID.
Configuration (DMX)
Use DMX configurations to operate the product with a DMX controller.
DMX Personalities
This setting allows you to choose a particular DMX personality.
1. Go to the DMX Channel main level.
2. Select the desired personality (1 Ch, 2 Ch, 3 Ch, or 6 Ch).
•OFF: The output is proportional (linear) to the dimmer channel value.
•Dimmer 1-3: The output follows the dimmer value based on the corresponding
dimmer curve, DIM1 being the fastest.
• See the DMX Control section for the highest starting address you can select for
each personality.
• Make sure that the starting addresses on the various products do not overlap due
to the new personality setting.

Page 15 of 19
Ovation E-160WW User Manual Rev. 1
OPERATION
DMX Control
In this mode, each product will respond to a unique starting address from the DMX controller. All products
with the same starting address will respond in unison.
1. Select a DMX personality as shown in DMX Personalities.
2. Set the starting address:
a. Go to DMX Address main level.
b. Select the starting address (001–512).
The highest recommended starting address for each DMX mode is as follows:
DMX Values
6 Ch
3 Ch
2 Ch
1 Ch
DMX Personality DMX Address
1 512
2511
3 510
6 507
Channel Function Value Percent/Setting
1 Dimmer 000 255 0–100%
2 Fine Dimmer 000 255 0–100%
3 Strobe 000 010
011 255 No function Strobe, slow to fast
4 Auto Program
000 010
011 070
071 130
131 190
191 255
No function
Auto 1, slow to fast
Auto 2, slow to fast
Auto 3, slow to fast
Auto 4, slow to fast
5 Auto Speed 000 255 Slow to fast
6 Dimmer Speed
000 051
052 101
102 152
153 203
204 255
Preset dimmer speed from display menu
Dimmer speed mode off
Dimmer speed mode 1 (fastest)
Dimmer speed mode 2
Dimmer speed mode 3 (slowest)
Channel Function Value Percent/Setting
1 Dimmer 000 255 0–100%
2 Fine Dimmer 000 255 0–100%
3 Strobe 000 010
011 255 No function Strobe, slow to fast
Channel Function Value Percent/Setting
1 Dimmer 000 255 0–100%
2 Fine Dimmer 000 255 0–100%
Channel Function Value Percent/Setting
1 Dimmer 000 255 0–100%

Page 16 of 19
TECHNICAL INFORMATION
Ovation E-160WW User Manual Rev. 1
5. TECHNICAL INFORMATION
Product Maintenance
To maintain optimum performance and minimize wear, clean this product frequently. Usage and
environment are contributing factors in determining the cleaning frequency.
Clean this product at least twice a month. Dust build-up reduces light output performance and can cause
overheating. This can lead to reduced light source life and increased mechanical wear.
To clean the product:
1. Unplug the product from power.
2. Wait until the product is at room temperature.
3. Use a vacuum (or dry compressed air) and a soft brush to remove dust collected on the external
vents.
4. Clean all transparent surfaces with a mild soap solution, ammonia-free glass cleaner, or isopropyl
alcohol.
5. Apply the solution directly to a soft, lint free cotton cloth or a lens cleaning tissue.
6. Softly drag any dirt or grime to the outside of the transparent surface.
7. Gently polish the transparent surfaces until they are free of haze and lint.
Always dry the transparent surfaces carefully after cleaning them.

Page 17 of 19
Ovation E-160WW User Manual Rev. 1
TECHNICAL
6. TECHNICAL SPECIFICATIONS
Dimensions and Weight
Note: Dimensions in inches rounded to the nearest hundredth.
Power
Light Source
Photometrics
Thermal
DMX
Ordering
Length Width Height Weight
19.49 in (495 mm) 11.22 in (285 mm) 19.17 in (487 mm) 14.2 lb (6.4 kg)
Power Supply Type Range Voltage Selection
Switching (internal) 100 to 240 VAC, 50/60 Hz Auto-ranging
Parameter 120 V, 60 Hz 230 V, 50 Hz
Consumption 103 W 102 W
Operating Current 0.9 A 0.5 A
Power linking current (products) 13.6A (X products) 13.6 A (X products)
Fuse T 3.15A, 250 V T 3.15A, 250 V
Power I/O U.S./Worldwide UK/Europe
Power input connector Neutrik powerCON A Neutrik powerCON A
Power output connector Neutrik powerCON B Neutrik powerCON B
Power Cord plug Edison (U.S.) Local Plug
Type Power Lifespan
LED 88 W 50,000 hours
Color Quantity Current
Warm White 1 2.3 A
Parameter 14°
Lens 19° Lens 26° Lens 36° Lens 50° Lens 15°~30° Lens 25°~50° Lens
Narrow Wide Narrow Wide
Beam Angle 8° 12° 16° 20° 31° 10° 15° 18° 24°
Field Angle 14° 18° 25° 33° 50° 16° 29° 28° 48°
Illuminance @ 5 m 10,814
lux 6,253 lux 3,189 lux 1,918 lux 743 lux 9,361 lux 2,947 lux 2,719 lux 1,072 lux
Lumens N/a 5,675 5,458 5,319 5,382 N/a
Maximum External Temperature Cooling System
113 °F (45 °C) Convection
I/O Connector Channel Range
3- and 5-pin XLR 1, 2, 3 or 6
Product Name Item Code UPC Number
Ovation E-160WW 03121237 781462215859
UL 1573
CSA C22.2 No. 166
E113093
R

Page 18 of 19
RETURNS
Ovation E-160WW User Manual Rev. 1
RETURNS
Send the product prepaid, in the original box, and with the original packing and accessories. Chauvet will
not issue call tags.
Call Chauvet and request a Return MerchandiseAuthorization (RMA) number before shipping the product.
Be prepared to provide the model number, serial number, and a brief description of the cause(s) for the
return.
Clearly label the package with an RMA number. Chauvet will refuse any product returned without an RMA
number.
Once you have the RMA number, provide the following information on a piece of paper and place it inside
the box:
• Your name
• Your address
• Your phone number
• RMA number
• A brief description of the problem
Be sure to pack the product properly. Any shipping damage resulting from inadequate packaging will be
your responsibility. FedEx packing or double-boxing are recommended.
Write the RMA number on a properly affixed label. DO NOT write the RMA number
directly on the box.
Chauvet reserves the right to use its own discretion to repair or replace returned
product(s).