Ovation E-260WW IP User manual

*Lens tubes
sold separately
User Manual

Ovation E-260WW IP User Manual Rev. 2
EDITION NOTES
The Ovation E-260WW IP User Manual includes a description, safety precautions, installation,
programming, operation and maintenance instructions for the Ovation E-260WW IP as of the release date
of this edition.
Trademarks
CHAUVET, the Chauvet logo and Ovation E-260WW IP are registered trademarks or trademarks of
Chauvet & Sons, LLC (d/b/a Chauvet and Chauvet Lighting) in the United States and other countries.
Other company and product names and logos referred to herein may be trademarks of their respective
companies.
Copyright Notice
The works of authorship contained in this manual, including, but not limited to, all design, text and images
are owned by Chauvet.
© Copyright 2017 Chauvet & Sons, LLC. All rights reserved.
Electronically published by Chauvet in the United States ofAmerica.
Manual Use
Chauvet authorizes its customers to download and print this manual for professional information purposes
only. Chauvet expressly prohibits the usage, copy, storage, distribution, modification, or printing of this
manual or its content for any other purpose without written consent from Chauvet.
Document Printing
For best results, print this document in color, on letter size paper (8.5 x 11 in), double-sided. If using A4
paper (210 x 297 mm), configure the printer to scale the content accordingly.
Intended Audience
Any person installing, operating, and/or maintaining this product should completely read through the guide
that shipped with the product, as well as this manual, before installing, operating, or maintaining this
product.
Disclaimer
Chauvet believes that the information contained in this manual is accurate in all respects. However,
Chauvet assumes no responsibility and specifically disclaims any and all liability to any party for any loss,
damage or disruption caused by any errors or omissions in this document, whether such errors or
omissions result from negligence, accident or any other cause. Chauvet reserves the right to revise the
content of this document without any obligation to notify any person or company of such revision, however,
Chauvet has no obligation to make, and does not commit to make, any such revisions. Download the latest
version from www.chauvetprofessional.com.
Document Revision
This Ovation E-260WW IP User Manual is the 2nd edition of this document. Go to
www.chauvetprofessional.com for the latest version.

Ovation E-260WW IP User Manual Rev. 2
TABLE OF CONTENTS
TOC 1
TABLE OF CONTENTS
1. Before You Begin....................................................................... 1
What Is Included ........................................................................................... 1
Claims........................................................................................................... 1
Manual Conventions ..................................................................................... 1
Symbols ........................................................................................................ 1
Safety Notes.................................................................................................. 2
Personal Safety.............................................................................................................. 2
Mounting and Rigging.................................................................................................... 2
Power and Wiring........................................................................................................... 2
Operation ...................................................................................................... 2
Expected LED Lifespan................................................................................. 2
2. Introduction ................................................................................ 3
Description.................................................................................................... 3
Features........................................................................................................ 3
Lens Tube..................................................................................................... 3
Product Overview.......................................................................................... 4
Product Dimensions...................................................................................... 5
3. Setup ........................................................................................... 6
AC Power...................................................................................................... 6
AC Plug.......................................................................................................................... 6
Power Linking................................................................................................ 6
DMX Linking.................................................................................................. 7
DMX Personalities.......................................................................................................... 7
Remote Device Management (RDM)............................................................ 7
Master/Slave Connectivity............................................................................. 7
Mounting ....................................................................................................... 8
Orientation...................................................................................................................... 8
Rigging........................................................................................................................... 8
Procedure....................................................................................................................... 8
Manual Beam Focus Control.......................................................................................... 9
Rotating the Barrel Assembly......................................................................................... 9
Accessory Slot ............................................................................................................... 9
4. Operation .................................................................................... 10
Control Panel Operation................................................................................ 10
Control Options............................................................................................. 10
Programming................................................................................................. 10
Control Panel Lock........................................................................................ 10
Passcode ...................................................................................................... 10
Menu Map..................................................................................................... 11
Configuration (Standalone)........................................................................... 12
Static Mode.................................................................................................................... 12
Focus Mode ................................................................................................................... 12
Auto Programs............................................................................................................... 12
Master/Slave.................................................................................................................. 12
Dimmer Profiles.............................................................................................................. 12
LED Frequency.............................................................................................................. 12
Fan Mode....................................................................................................................... 13
Back Light ...................................................................................................................... 13
Gobo Power................................................................................................................... 13
System Information........................................................................................................ 13
Factory Reset................................................................................................................. 13

TABLE OF CONTENTS
Ovation E-260WW IP User Manual Rev. 2
TOC 2
Configuration (DMX) ..................................................................................... 13
DMX Personalities.......................................................................................................... 13
DMX Control................................................................................................................... 13
DMX Values.................................................................................................. 14
6 Ch................................................................................................................................ 14
3 Ch................................................................................................................................ 14
2 Ch................................................................................................................................ 14
1 Ch................................................................................................................................ 14
5. Technical Information................................................................ 15
Product Maintenance.................................................................................... 15
Technical Specifications ............................................................... 16
Returns............................................................................................ 17
Contact Us ...................................................................................... 18

Page 1 of 18
Ovation E-260WW IP User Manual Rev. 2
BEFORE YOU BEGIN
1. BEFORE YOU BEGIN
What Is Included
Claims
Carefully unpack the product immediately and check the container to make sure all the parts are in the
package and are in good condition.
If the box or the contents (the product and included accessories) appear damaged from shipping, or show
signs of mishandling, notify the carrier immediately, not Chauvet. Failure to report damage to the carrier
immediately may invalidate your claim. In addition, keep the box and contents for inspection.
For other issues, such as missing components or parts, damage not related to shipping, or concealed
damage, file a claim with Chauvet within 7 days of delivery.
Manual Conventions
Symbols
• Ovation E-260WW IP
• Seetronic Powerkon IP65 Power Cord • Warranty Card • Quick Reference Guide
Convention Meaning
1–512 A range of values
50/60 Aset of values of which only one can be chosen
<SET> A button on the product’s control panel
Settings A product function or a menu option
Symbol Meaning
Critical installation, configuration, or operation information. Not following these
instructions may makethe product not work, cause damage to the product, or cause
harm to the operator.
Important installation or configuration information. The product may not function
correctly if this information is not used.
Useful information.
Any reference to data or power connections in this manual assumes the use of
Seetronic IP rated cables.
The term “DMX” used throughout this manual refers to the USITT DMX512-A
digital data transmission protocol.

Page 2 of 18
BEFORE YOU BEGIN
Ovation E-260WW IP User Manual Rev. 2
Safety Notes
Read all the following safety notes before working with this product. These notes contain important
information about the installation, usage, and maintenance of this product.
Personal Safety
• Avoid direct eye exposure to the light source while the product is on.
• Always disconnect the product from the power source before cleaning or replacing the fuse.
• Always connect the product to a grounded circuit to avoid the risk of electrocution.
• Do not touch the product’s housing when operating because it may be very hot.
Mounting and Rigging
• Do not submerge this product (IP65). Temporary outdoor operation is fine.
• When using this product in an outdoor environment, use IP65 (or higher) rated power and data
cables. Secure unused power and data ports with attached IP65 covers.
• CAUTION:Whentransferringproductfrom extreme temperatureenvironments,(e.g.,coldtruck to warm,
humid ballroom) condensation may form on the internal electronics of the product. To avoid causing a
failure, allow product to fully acclimate to the surrounding environment before connecting it to power.
• Not for permanent outdoor installation in locations with extreme environmental conditions. This
includes, but is not limited to:
• Exposure to a marine/saline environment (within 3 miles of a saltwater body of water).
• Locations where the normal high or low temperatures exceed the temperature ranges in this
manual.
• Locations that are prone to flooding or being buried in snow.
• Areas where the product will be subjected to extreme radiation or caustic substances.
• Mount this product in a location with adequate ventilation, at least 20 in (50 cm) from adjacent
surfaces.
• Make sure there are no flammable materials close to the product when operating.
• When hanging this product, always secure to a fastening device using a safety cable.
Power and Wiring
• Always make sure you are connecting the product to the proper voltage in accordance with the
specifications in this manual or on the product’s specification label.
• Never connect the product to a dimmer pack or rheostat.
• Never disconnect this product by pulling or tugging on the power cable.
Operation
• Donot operate this product ifthereis damage on the housing,lenses,orcables.Havethe damaged
parts replaced by an authorized technician at once.
• Do not cover the ventilation slots when operating to avoid internal overheating.
• The maximum ambienttemperatureis 113 °F (45 °C). Do not operate the product at higher temperatures.
• In the event of a serious operation problem, stop using this product immediately!
Expected LED Lifespan
LEDs gradually decline in brightness over time, primarily because of heat. LEDs that are arranged in
clusters experience higher operating temperatures than single LEDs. For this reason, operating clustered
LEDs at their fullest intensity significantly reduces the LEDs’ lifespan. Under normal conditions, this
lifespan is 40,000 to 50,000 hours. If extending this lifespan is vital, lower the operating temperature by
improving the ventilation around the product, thus reducing the ambient temperature. In addition, limiting
the overall projection intensity may extend the LEDs’ lifespan.
This product contains no user-serviceable parts. Any reference to servicing in
this User Manual will only apply to properly trained, certified technicians. Do not
open the housing or attempt any repairs.
All applicable local codes and regulations apply to proper installation of this
product.
If your Chauvet product requires service, contact Chauvet Technical Support.

Page 3 of 18
Ovation E-260WW IP User Manual Rev. 2
INTRODUCTION
2. INTRODUCTION
Description
The Ovation E-260WW IP is a high-powered warm white ellipsoidal light that projects a flat, even field.
Standard framing shutters, a gobo/effect slot, and interchangeable lens barrels provide versatility to fit any
application. The Ovation E-260WW IP is IP65 rated and features IP rated power and DMX connections.
Selectable dimming curves ensure smooth fading cues that intermix well with the output of conventional
theatre ellipsoidal lights.
Features
• Operating modes:
• 1-channel: dimmer control
• 2-channel: dimmer and fine dimmer control
• 3-channel: dimmer, fine dimmer, and strobe control
• 6-channel: dimmer, fine dimmer, strobe control, auto programs, auto speed, and dimmer mode
• Warm white ERS-style fixture with output exceeding a tungsten 750 W source
• Fully IP65 rated for seasonal use indoors or out
• Use of our standard Ovation beam shaping shutters and lenses lends familiarity and ease of use to
the fixture
• Ultra smooth 16-bit dimming, and 8-bit dimming curves to complement any lighting scheme
• Flat, even field of light for superior gobo projection
• RDM (Remote Device Management) for added flexibility
• Adjustable PWM (Pulse Width Modulation) to avoid flickering on camera
Lens Tube
The following lens tubes are available for purchase:
• 14° w/ Gel frame (7.5 in/191 mm accessories)
• 19° w/ Gel frame (6.25 in/159 mm accessories)
• 26° w/ Gel frame (6.25 in/159 mm accessories)
• 36° w/ Gel frame (6.25 in/159 mm accessories)
• 50° w/ Gel frame (6.25 in/159 mm accessories)
• 15°–30° w/ Gel frame (7.5 in/191 mm accessories)
• 25°–50° w/ Gel frame (7.5 in/191 mm accessories)

Page 4 of 18
INTRODUCTION
Ovation E-260WW IP User Manual Rev. 2
Product Overview
DMX
In/Out
Display
Menu Buttons
Seetronic Powerkon In
Barrel Rotation Knobs
Seetronic Powerkon Out
Handle
Pattern Holder Slot
(A-size holder for 3-in patterns.
B-size holder for 2.5-in and 2.75-
in patterns, sold separately)
Framing Shutter (x4)Accessory Slot
Beam Focus Knobs
Gel Frame Holder
Light EngineBarrel
Assembly
Lens Tube
(sold separately)
IP-Rated Plug Covers
Gobo Power Out
(For Future Use)

Page 5 of 18
Ovation E-260WW IP User Manual Rev. 2
INTRODUCTION
Product Dimensions
23.5 in
597 mm
13.46 in
342 mm
19.92 in
506 mm
12.64 in
321 mm

Page 6 of 18
SETUP
Ovation E-260WW IP User Manual Rev. 2
3. SETUP
AC Power
Each Ovation E-260WW IP has an auto-ranging power supply that works with an input voltage range of
100 to 240 VAC, 50/60 Hz. To determine the power requirements for each Ovation E-260WW IP, refer to
the label affixed to the product. You can also refer to the Technical Specifications chart in this manual.
The listed current rating indicates the maximum current draw during normal operation. For more
information, download Sizing Circuit Breakers from the Chauvet website: www.chauvetprofessional.com.
AC Plug
The Ovation E-260WW IP comes with a power input cord terminated with a Seetronic Powerkon A
connector on one end and an Edison plug on the other end (U.S. market). If the power input cord that came
with your product has no plug, or if you need the change the plug, use the table below to wire the new plug.
Power Linking
The product supports power linking. You can power link up to 7 products at 120 V; up to 12 at 208 V; or up
to 13 at 230 V.
This product comes with a power input cord. Power linking cables are available from Chauvet for purchase.
• Always connect theproduct to a protected circuit (circuit breaker or fuse). Make sure the
product has an appropriate electrical ground to avoid the risk of electrocution or fire.
• To eliminate unnecessary wear and improve its lifespan, during periods of non-use
completely disconnect the product from power via breaker or by unplugging it.
Never connect the product to a rheostat (variable resistor) or dimmer circuit, even if the
rheostat or dimmer channel serves only as a 0 to 100% switch.
Connection Wire (U.S.) Wire (Europe) Screw Color
AC Live Black Brown Yellow or Brass
AC Neutral White Blue Silver
AC Ground Green/Yellow Green/Yellow Green
• To preserve the IP65 rating and the warranty of this product Seetronic Powerkon cables
must be used.
• Insert the attached IP65 rated plugs into the corresponding power/data connections
when not in use.

Page 7 of 18
Ovation E-260WW IP User Manual Rev. 2
SETUP
DMX Linking
You can link the Ovation E-260WW IP to a DMX controller using a 5-pin DMX connection. If using other
DMX-compatible products with this product, you can control each individually with a single DMX controller.
DMX Personalities
The Ovation E-260WW IP uses a 5-pin DMX data connection for the 1-, 2-, 3-, and 6-channel DMX
personalities.
• Refer to the Introduction chapter for a brief description of each DMX personality.
• Refer to the Operation chapter to learn how to configure the Ovation E-260WW IP to work in these
personalities.
•TheDMX Values section provides detailed information regarding the DMX personalities.
Remote Device Management (RDM)
Remote Device Management, or RDM, is a standard for allowing DMX-enabled devices to communicate
bi-directionally along existing DMX cabling. Check the DMX controller’s User Manual or with the
manufacturer as not all DMX controllers have this capability. The Ovation E-260WW IP supports RDM
protocol that allows feedback to make changes to menu map options.
Master/Slave Connectivity
The Master/Slave mode allows a Ovation E-260WW IP (the master) to control one or more
Ovation E-260WW IP products (the slaves) without a DMX controller. One Ovation E-260WW IP becomes
the master when running an auto program, or by being in Static mode.
You must configure each slave’s control panel to operate in Slave mode. During Master/Slave operation,
the slaves will operate in unison with the master.
If you are not familiar with or need more information about DMX standards, Master/Slave
connectivity, or the DMX cables needed to link this product to a DMX controller,
download the DMX Primer from the Chauvet website: www.chauvetprofessional.com.
DO NOT connect a DMX controller to products operating in Master/Slave mode. The
DMX controller signals may interfere with the signals from the master.
•TheOperation section of this manual provides detailed instructions on how to
configure the master and slaves.
• If you are not familiar with or need more information about DMX standards, or the DMX
cables needed to link this product to a DMX controller, download the DMX Primer from
the Chauvet website: www.chauvetprofessional.com.
• To preserve the IP65 rating and the warranty of this product, IP65 data cables must be used.
• Insert the attached IP65 rated plugs into the corresponding power/data connections
when not in use.

Page 8 of 18
SETUP
Ovation E-260WW IP User Manual Rev. 2
Mounting
Before mounting the product, read and follow the safety recommendations indicated in the Safety Notes.
For our CHAUVET Professional line of mounting clamps, go to http://trusst.com/products/.
Orientation
Always mount this product in a safe position, making sure there is adequate room for ventilation,
configuration, and maintenance.
Rigging
Chauvet recommends using the following general guidelines when mounting this product.
• Before deciding on a location for the product, make sure there is easy access to the product for
maintenance and programming purposes.
• Make sure that the structure onto which you are mounting the product can support the product’s
weight. See the Technical Specifications for weight information.
• When mounting the product overhead, always use a safety cable. Mount the product securely to a
rigging point, whether an elevated platform or a truss.
• When rigging the product onto a truss, use a mounting clamp of appropriate weight capacity.
• When power linking multiple products, mount the products close enough for power linking cables to
reach.
• The bracket adjustment knob allows for directional adjustment when aiming the product to the
desired angle. Only loosen or tighten the bracket knob manually. Using tools could damage the knob.
Procedure
The Ovation E-260WW IP comes with a hanging/mounting bracket to which mounting clamps can be
attached. The bracket has 13-mm holes, which are appropriate for this purpose. Be sure the clamps used
are capable of supporting the weight of this product. Use at least one mounting point per product where
necessary.
Mounting Diagram
Mounting Clamp
Safety Cable
Secure the safety cable using the
passageway on the top of the product
Mounting Bracket
Bracket Adjustment Knob
AlternateYoke
Attachment

Page 9 of 18
Ovation E-260WW IP User Manual Rev. 2
SETUP
Manual Beam Focus Control
The Ovation E-260WW IP has a manual focus, which is adjusted as follows:
1. Locate the beam focus knobs at the top and bottom of the barrel assembly.
2. Loosen the knobs by turning them counter-clockwise.
3. Slide the lens tube forward or backward until you achieve the desired focus or beam edge.
4. Tighten the knobs by turning them clockwise, which lock the lens tube’s position.
Rotating the Barrel Assembly
The Ovation E-260WW IP allows manual rotation of the barrel assembly, as follows:
1. Locate the barrel rotation knobs at the top and bottom of the light engine.
2. Loosen the knobs by turning them counter-clockwise.
• Note: Do not remove the knobs.
3. Rotate the barrel to the desired position, up to 25° in either direction from the centered position.
4. Tighten the knobs by turning them clockwise, which lock the barrel’s position.
Accessory Slot
The Ovation E-260WW IP has an accessory slot, which holds a drop-in iris, a motorized pattern device, or
various other optional accessories (sold separately).
1. Loosen the thumbscrews on the slot cover.
•Note: Do not remove the thumbscrews.
2. Slide the cover forward.
3. Insert an accessory.
•Note: Make sure to insert the accessory correctly. For example, make sure the iris handle
extends upward from the slot.
4. Slide the cover back. Make sure any handles or adjustment tools that stick out the top are able to
function correctly.
5. Tighten the thumbscrews to secure the cover.
To avoid changing menu settings while focusing the Ovation E-260WW IP, press and hold
the <ENTER> button for 3 seconds. This will put the product in “Focus Mode” by
increasing the intensity to 100%. To exit out of focus mode, press <MENU>.
Make sure the barrel assembly is oriented with the pattern holder and accessory slots at
the top of the product.
• When not using the accessory slot, replace and secure the slot cover to prevent light
leakage during operation.
• When obtaining any optional accessories, be sure the items are compatible with the
Ovation E-260WW IP.
Iris Handle
Thumbscrews
Accessory
Slot Cover
Sample
Drop-in Iris

Page 10 of 18
OPERATION
Ovation E-260WW IP User Manual Rev. 2
4. OPERATION
Control Panel Operation
Control Options
Set the Ovation E-260WW IP starting address in the 001-512 DMX range. This enables control of up to 85
products in the 6-channel 6Ch personality.
Programming
Refer to the Menu Map to understand the menu options. The menu map shows the main level and a
variable number of programming levels for each option.
• To go to the desired main level, press <MENU> repeatedly until the option shows on the display.
Press <ENTER> to select. This will take you to the first programming level for that option.
• To select an option or value within the current programming level, press <UP> or <DOWN> until
the option shows on the display. Press <ENTER> to select. In this case, if there is another
programming level, you will see that first option, or you will see the selected value.
• Press <MENU> repeatedly to exit to the previous main level.
Control Panel Lock
This setting enables you to activate or disable the control panel lock, which keeps unauthorized users from
changing the product’s settings.
1. Go to the Key Lock main level.
2. Select On or Off.
Passcode
After being prompted to enter the passcode:
Press <UP>, <DOWN>, <UP>, <DOWN>, <ENTER>.
Button Function
<MENU> Exits from the current menu or function
<ENTER> Enables the currently displayed menu or sets the currently selected value in to the current
function
<UP> Navigates upward through the menu list or increases the numeric value when in a function
<DOWN> Navigates downward through the menu list or decreases the numeric value when in a function
When the control panel lock is activated, in order to access the products main
programming level, the product will prompt for the passcode. Enter the
passcode as described below.

Page 11 of 18
Ovation E-260WW IP User Manual Rev. 2
OPERATION
Menu Map
Main Level Programming Levels Description
DMX Address Address <001–512> Selects DMX address (highest channel restricted to
personality chosen).
DMX Channel
1 Ch 1-channel: dimmer
2 Ch 2-channel: 16-bit dimmer
3 Ch 3-channel: 16-bit dimmer, strobe
6 Ch 6-channel: 16-bit dimmer, strobe, auto programs,
auto speed, dimmer mode
Static Dimmer <0–255> Sets the intensity of the light output
Strobe Sets the strobe rate
Auto Show Auto 1–4 <1–100> Selects automatic programs and speed
Master/Slave
Mode Master Master mode
Slave DMX slave mode
Dimmer Mode Off Linear dimming
Dimmer 1–3 Dimming curves: Dimmer 1 (fast) to Dimmer 3
(slow)
LED
Frequency
600Hz
PWM frequency
1200Hz
2000Hz
4000Hz
6000Hz
25KHz
Fan Mode Auto Fan speed based on product temperature
On Fan always at maximum
Back Light
On Display backlight always on
10S Turns off display backlight after 10 sec of inactivity
20S Turns off display backlight after 20 sec of inactivity
30S Turns off display backlight after 30 sec of inactivity
Key Lock On Locks display (password is <UP>, <DOWN>, <UP>,
<DOWN>, <ENTER>)
Off
Gobo Power On Enables or disables gobo power output
Off
Information Fixture Hours <_ _ _ _H> Shows total product hours Version <V_._> Shows installed software version
UID
____________ Shows product ID
Reset Factory No Reset to factory defaults
Yes

Page 12 of 18
OPERATION
Ovation E-260WW IP User Manual Rev. 2
Configuration (Standalone)
Use standalone configuration to operate the product without a DMX controller.
Static Mode
The Static mode allows for permanent dimmer and strobe presets without a DMX controller.
1. Go to the Static main level.
2. Select Dimmer or Strobe.
3. Select the desired value (0–255).
Focus Mode
Focus mode allows for focusing of the Ovation E-260WW IP without changing any menu settings.
1. Press and hold <ENTER> for 3 seconds. The output intensity will increase to 100%.
2. Press <MENU> to exit focus mode and restore the settings.
Auto Programs
Auto programs allow for dynamic blinder effects without a DMX controller.
1. Go to the Auto Show main level
2. Select the desired auto (Auto 1–4).
3. Select the desired speed (1–100).
Master/Slave
The Master/Slave mode allows a group of Ovation E-260WW IP products (the slaves) to simultaneously
duplicate the output of another Ovation E-260WW IP (the master) without a DMX controller.
To set each of the slaves:
1. Go to the Master/Slave main level
2. Select Slave.
To set the master:
1. Go to the Master/Slave main level
2. Select Master.
3. Select an auto program as explained in Auto Programs, or a static setting.
Dimmer Profiles
This setting determines how fast the output of the Ovation E-260WW IP changes when you modify the
output value. This setting provides four different options to simulate the dimming curve of an incandescent
lighting product.
• Go to the Dimmer Mode main level.
• Select a dimmer curve (OFF, Dimmer 1, Dimmer 2, or Dimmer 3).
LED Frequency
This option changes the Pulse Width Modulation (PWM) frequency of the LEDs on the Ovation E-260WW
IP. 1. Go to the LED Frequency main level.
2. Select PWM Frequency (600Hz, 1200Hz,2000Hz,4000Hz, 6000Hz, or 25Khz).
The auto programs cannot be edited.
• The master is the one that runs a program whether inAuto or Static mode.
• Do not connect a DMX controller to the products configured for Master/Slave
operation. The DMX controller may interfere with signals from the master.
• The master should be the first product in the daisy chain.
OFF: The output is proportional (linear) to the dimmer channel value.
Dimmer 1-3: The output follows the dimmer value based on the corresponding dimmer
curve, DIM1 being the fastest.

Page 13 of 18
Ovation E-260WW IP User Manual Rev. 2
OPERATION
Fan Mode
This setting determines how the fan speed on the Ovation E-260WW IP is set.
1. Go to the Fan Mode main level
2. Select Auto (fan speed will increase or decrease based on product temperature) or On (fan
speed will always be at maximum).
Back Light
This setting allows for selection of the amount of time the backlight on the Ovation E-260WW IP’s display
stays on after the last button is pressed on the control panel.
1. Go to the Back Light main level.
2. Select On (remains on), 10S (10 seconds), 20S (20 seconds), or 30S (seconds).
Gobo Power
This setting is for future use, and should remain set to Off.
System Information
This option displays the total number of hours the product has run, the installed software version, and the
product’s UID.
1. Go to the Information main level.
2. Select Fixture Hours, Version, or UID.
Factory Reset
This option restores the Ovation E-260WW IP to factory default settings.
1. Go to the Reset Factory main level.
2. Select No or Yes.
Configuration (DMX)
Use DMX configurations to operate the product with a DMX controller.
DMX Personalities
This setting allows you to choose a particular DMX personality.
1. Go to the DMX Channel main level.
2. Select the desired personality (1 Ch, 2 Ch, 3 Ch, or 6 Ch).
DMX Control
In this mode, each product will respond to a unique starting address from the DMX controller. All products
with the same starting address will respond in unison.
1. Select a DMX personality as shown in DMX Personalities.
2. Set the starting address:
a. Go to DMX Address main level.
b. Select the starting address (001–512).
The highest recommended starting address for each DMX mode is as follows:
•SeetheDMX Values section for the highest starting address you can select for
each personality.
• Make sure that the starting addresses on the various products do not overlap due
to the new personality setting.
DMX Personality DMX Address
1 512
2511
3 510
6 507

Page 14 of 18
OPERATION
Ovation E-260WW IP User Manual Rev. 2
DMX Values
6 Ch
3 Ch
2 Ch
1 Ch
Channel Function Value Percent/Setting
1 Dimmer 000 255 0–100%
2 Fine Dimmer 000 255 0–100%
4Strobe 000 010 No function
011 255 Strobe, slow to fast
4 Auto Program
000 010 No function
011 070 Auto 1, slow to fast
071 130 Auto 2, slow to fast
131 190 Auto 3, slow to fast
191 255 Auto 4, slow to fast
5AutoSpeed 000255 Slow to fast
6 Dimmer Speed
000 051 Preset dimmer speed from display menu
052 101 Dimmer speed mode off
102 152 Dimmer speed mode 1 (fastest)
153 203 Dimmer speed mode 2
204 255 Dimmer speed mode 3 (slowest)
Channel Function Value Percent/Setting
1 Dimmer 000 255 0–100%
2 Fine Dimmer 000 255 0–100%
3Strobe 000 010 No function
011 255 Strobe, slow to fast
Channel Function Value Percent/Setting
1 Dimmer 000 255 0–100%
2 Fine Dimmer 000 255 0–100%
Channel Function Value Percent/Setting
1 Dimmer 000 255 0–100%

Page 15 of 18
Ovation E-260WW IP User Manual Rev. 2
TECHNICAL INFORMATION
5. TECHNICAL INFORMATION
Product Maintenance
To maintain optimum performance and minimize wear, clean this product frequently. Usage and
environment are contributing factors in determining the cleaning frequency.
Clean this product at least twice a month. Dust build-up reduces light output performance and can cause
overheating. This can lead to reduced light source life and increased mechanical wear.
To clean the product:
1. Unplug the product from power.
2. Wait until the product is at room temperature.
3. Use a vacuum (or dry compressed air) and a soft brush to remove dust collected on the external
vents.
4. Clean all transparent surfaces with a mild soap solution, ammonia-free glass cleaner, or isopropyl
alcohol.
5. Apply the solution directly to a soft, lint free cotton cloth or a lens cleaning tissue.
6. Softly drag any dirt or grime to the outside of the transparent surface.
7. Gently polish the transparent surfaces until they are free of haze and lint.
Always dry the transparent surfaces carefully after cleaning them.

Page 16 of 18
TECHNICAL SPECIFICATIONS
Ovation E-260WW IP User Manual Rev. 2
6. TECHNICAL SPECIFICATIONS
Dimensions and Weight
Note: Dimensions in inches rounded to the nearest decimal digit.
Power
Light Source
Photometrics
Thermal
DMX
Ordering
Length Width Height Weight
19.49 in (495 mm) 11.14 in (342 mm) 19.92 in (506 mm) 20.2 lb (9.2 kg)
Power Supply Type Range Voltage Selection
Switching (internal) 100 to 240 VAC, 50/60 Hz Auto-ranging
Parameter 120 V, 60 Hz 208 V, 60 Hz 230 V, 50 Hz
Consumption 221 W 215 W 213 W
Operating Current 1.85 A 1.11 A 1.01 A
Power linking current
(products) 13.6 A (7 products) 13.6 A (12 products) 13.6 A (13 products)
Power I/O U.S./Worldwide UK/Europe
Power input connector Seetronic Powerkon IP65 Seetronic Powerkon IP65
Power output connector Seetronic Powerkon IP65 Seetronic Powerkon IP65
Power Cord plug Edison (U.S.) Local Plug
Type Color Quantity Power Current Lifespan
LED Warm White 1 202 W 3.6 A 50,000 hours
Parameter 14°
Lens 19° Lens 26° Lens 36° Lens 50° Lens 15°–30° Lens (Narrow/Wide) 25°–50° Lens (Narrow/Wide)
Illuminance @ 5 m 14,149
lux 9,256 lux 6,910 lux 4,053 lux 1,703 lux 12,430 lux 5,339 lux 4,997 lux 3,295 lux
Lumens N/A 7,587 10,284 10,121 9,655 N/A N/A
Beam Angle 11° 13° 16° 20° 28° 12° 14° 21° 22°
Field Angle 14° 19° 26° 36° 50° 15° 29° 26° 46°
Maximum External Temperature Cooling System
113 °F (45 °C) Fan-assisted convection
I/O Connector Channel Range
5-pin XLR 1, 2, 3 or 6
Product Name Item Name Item Code UPC Number
Ovation E-260WW IP OVATIONE260WWIP 03121239 781462215873