Overland Storage SnapServer XSR 120 User manual

10400669-001 ©2015 Overland Storage, Inc. Page 1 of 4
*10400669001*
SnapServer XSR 120™/ SnapScale X2®Node
Spare Control Panel Instructions
This document describes how to remove and replace a control
panel (left flange) on a SnapServer XSR 120 or SnapScale X2
node from Overland Storage.
WARNING: To reduce the risk of electric shock or damage to
equipment, always remove any power cords while working
with the unit.
WARNUNG: Um das Risiko eines elektrischen Schlags oder
Schäden am Gerät zu vermeiden, ziehen Sie stets den
Netzstecker, bevor Sie an der Einheit arbeiten.
AVERTISSEMENT: Pour réduire le risque de choc électrique
ou endommagement de l'équipement, retirez toujours les
cordons électriques en travaillant avec l'appareil.
CAUTION: While working with the unit, observe standard
Electrostatic Discharge (ESD) precautions to prevent damage
to micro-circuitry or static-sensitive devices.
Prepare the Unit
Power Off and Disconnect
If the unit is still running, power it down cleanly:
1. Power off the server/cluster:
•SnapServer: Use the Web Management Interface to
shut down the server ( Maintenance > Reboot and
Shutdown > Shutdown
).
•SnapScale: There are two power-off options available.
•Shut off the entire cluster by using the Web
Management Interface (
Maintenance > Shutdown/
Restart > Shutdown ).
This is the recommended option. By shutting down
the entire cluster, no peer sets will need to be rebuilt
when it is reactivated. However, the cluster will be
offline and unavailable during the repairs.
•Shut off just the affected node by briefly pressing
the Power button on a node.
By shutting down only the node, the cluster remains
online and active. However, some peer sets will be
operating with either less (3x replication) or no (2x
replication) redundancy while the node is down and
afterwards when the peer sets are being rebuilt.
2. When all the LEDs are off, disconnect the power cords.
3. Disconnect the remaining cables from the unit, noting
their locations.
Power Button X2 Node
XSR 120Power Sockets Cable Ports

10400669-001 ©2015 Overland Storage, Inc. Page 2 of 4
Spare Control Panel Instructions
Remove the Front Bezel
1. Carefully take hold of the front bezel and pull it straight
out from the appliance until the magnets release.
2. Set the bezel aside on a secure surface.
Remove the Drives
IMPORTANT: Overland recommends that you remove the disk
drives to reduce the unit’s weight prior to removal.
Remove all the drive carriers. For SnapScale, note from which
bays they were removed. Blank carriers can remain in their
bays.
NOTE: Do not remove the disk drives from their carriers. Doing so
voids the drive warranty.
1. Press the release button on the right side of the carrier.
2. Using the built-in handle, pull the carrier out.
3. Number the carrier and set it on a secure surface.
4. Repeat Steps 1–3 for all the remaining drive carriers.
Remove Unit from Rack
WARNING: It is recommended that a mechanical lifter (or at
least two people) be used during rack installation or removal
to prevent injury.
WARNUNG: Um Verletzungen zu vermeiden, empfehlen wir
zur Rack-Installation oder -Deinstallation die Nutzung einer
mechanischen Hebehilfe (oder mindestens zwei Personen).
AVERTISSEMENT: Pour éviter toute blessure il est
recommande qu'un monte-charge (ou deux personnes au
moins) soit utilisé lors de l'installation ou de l'enlèvement du
support.
1. Remove and retain the four screws securing the unit to
the rack.
2. With a lifter positioned in front of the array, release the
rail locks and slide the chassis out onto the lifter.
3. Move the chassis onto a secure surface.
Replace the Control Panel Flange
Remove LED Wire Cover & Flange
1. Remove and retain the rear screw on the wire cover.
2. Pull the rear of the cover away from the chassis, slide it
out, and set it aside.
3. Remove and retain the two screws holding the flange.
Be careful not to put a strain on the wiring.
XSR 120
Press
1
5
9
2
6
10
3
7
11
4
8
12
Secure Surface

10400669-001 ©2015 Overland Storage, Inc. Page 3 of 4
Spare Control Panel Instructions
Remove the Wiring
1. Using a small tool, loosen both the top and bottom of the
wiring connector.
2. Gently pull the wiring connector out of its socket.
Dispose of the old flange properly. There is no need to
return it.
Install New Flange
1. Carefully insert the wiring connector into the socket on
the new flange.
2. Gently push the ends of the connector to verify that it
seats correctly.
Reinstall LED Wire Cover & Flange
1. Using the retained screws, attach the new flange.
2. Insert the front of the cover into its slot, push it in and
against the chassis.
Verify the alignment of the tabs along the cover into the
slots on the chassis.
3. Using the retained screw, secure the cover at the rear.
Reassemble the Unit
Return Chassis to Rack
1. Slide out the middle rails from the rack.
2. Using the mechanical lifter, position the chassis in front
of the rack.
3. Insert the inner rails into the middle rails and slide the
unit into the rack.
4. Using the four retained screws, secure the unit.
Reinstall Drives
1. Position a drive assembly in front of its empty bay.
For SnapScale, they must be returned to the bay they
were removed from. Refer to the number on the assembly.
2. Slide the assembly in until the latch clicks, securing it.
3. Repeat Steps 1–2 for all remaining drive carriers.
IMPORTANT: To maintain proper airflow and cooling, a drive
assembly or a blank carrier must be installed in every bay. No
empty bays are allowed.

10400669-001 ©2015 Overland Storage, Inc. Page 4 of 4
http://support.overlandstorage.com
You can get additional technical support on the Internet at the Overland Storage Support web page, or by contacting Overland Storage using
the information found on the Contact Us page on our web site.
Spare Control Panel Instructions
Reattach Cables and Power Cords
1. Reattach all cables to the same connections as before.
2. Attach the power cords.
3. At the front of the unit, press the power switch for less
than a second to power the unit ON.
Reattach the Bezel
1. Position the bezel with the tabs aligned inside the top
and bottom edges of the chassis.
2. Move bezel toward the unit until the magnets connect.
3. Verify that the bezel is aligned properly, all the LEDs are
visible, and the Power panel is centered in the left flange.
XSR 120Power Sockets Cable Ports
Magnets Tabs