Ovislink OV604V User manual

OV604V
User Manual
VER: 1.0

i
Contents
1Introduction............................................................................................1
1.1 Application ..........................................................................................1
1.2 Features..............................................................................................1
1.3 Standards Compatibility and Compliance ............................................2
1.4 Safety Cautions...................................................................................2
1.5 LED Status Description........................................................................3
1.5.1 LED Status................................................................................3
1.5.2 Rear Panel ...............................................................................4
2Hardware Installation .............................................................................4
2.1 Connecting the DSL Router.................................................................5
2.2 Factory Reset Button...........................................................................5
3PC Network Configuration......................................................................6
4Web-Based Management ......................................................................8
4.1 Logging In to the Modem.....................................................................8
4.1.1 First-Time Login........................................................................8
4.2 DSL Router Device Information...........................................................9
4.2.1 Summary of Device Information..............................................10
4.2.2 WAN Interface Information......................................................10
4.2.3 Statistics................................................................................. 11
4.2.4 Route Table Information..........................................................15
4.2.5 ARP Table Information............................................................16
4.2.6 DHCP IP Lease Information....................................................16
4.3 Advanced Setup................................................................................17
4.3.2 Connection Type of WAN Service...........................................20
4.3.3 LAN Configuration ..................................................................38
4.3.4 NAT ........................................................................................41
4.3.5 Security ..................................................................................47
4.3.6 Parental Control......................................................................51
4.3.7 Routing...................................................................................52
4.3.8 DNS........................................................................................55

ii
4.4 Diagnostics .......................................................................................57
4.5 Management.....................................................................................57
4.5.1 Settings ..................................................................................58
4.5.2 Internet Time...........................................................................58
4.5.3 Access Control .......................................................................60
4.5.4 Update Software.....................................................................60
4.5.5 Reboot....................................................................................61

1
1 Introduction
The XDSL OV604V is a high-speed VDSL2 router, uplink rate up to 40 Mbps and
downlink rate up to 80 Mbps. It provides sufficient bandwidth for high performance
connection to the Internet, online gaming, video on demand (VOD), video
conferencing, and high definition television (HDTV). It has Web-based graphic user
interface (GUI), in which you can easily modify the settings and connect to your ISP.
It also provides flow statistics, connection status, and other detailed information.
The XDSL OV604V is easily upgraded and provides terminal users and ISP with
the guarantee of future.
The XDSL OV604V provides one RJ11 telephone interface, ,four RJ45 Ethernet
LAN interfaces. The telephone interface is used for connecting to the Internet
provided by the telecom carrier. The Ethernet is used for connecting to computers,
through which you can access the Internet. Computers that are connected with the
router through the Ethernet can establish a small local network area (LAN). Those
computers can communicate with each other, sharing resources and files. The
XDSL OV604V is an ideal broadband CPE solution for both home users who wish
to share high-speed Internet access and small offices that wish to do business on
the Internet.
1.1 Application
VOD and video-conferencing
Network online gaming
IP over television (IPTV )and HDTV
High Internet access sharing
High rate broadband sharing
Small enterprises application
Home networking application
1.2 Features

2
User-friendly GUI for web configuration
Several pre-configured popular games. Just enable the game and the port
settings are automatically configured.
Configurable as a DHCP server on your network
Compatible with all standard Internet applications
Industry standard and interoperable DSL interface
Support virtual server, IP filter, DMZ host, and much more
Simple web-based status page displays a snapshot of system configuration,
and links to the configuration pages
Downloadable flash software updates
Support for up to 16 permanent virtual circuits (PVC)
Support for up to 8 PPPoE sessions
1.3 Standards Compatibility and Compliance
Support application level gateway (ALG)
ITU G.992.1 (G.dmt)
ITU G.992.2 (G.lite)
ITU G.994.1 (G.hs)
ITU G.992.3 (ADSL2)
ITU G.992.5 (ADSL2+)
ITU G.993.1 (VDSL)
ITU G993.2 (VDSL2)
ANSI T1.413 Issue 2
IEEE 802.3
IEEE 802.3u
1.4 Safety Cautions
Follow the following announcements to protect the device from risks and damage
caused by fire and electric power:
Use volume labels to mark the type of power.
Use the power adapter that is packed within the device package.
Pay attention to the power load of the outlet or prolonged lines. An
overburden power outlet or damaged lines and plugs may cause electric

3
shock or fire accident. Check the power cords regularly. If you find any
damage, replace it at once.
Proper space left for heat dissipation is necessary to avoid any damage
caused by overheating to the device. The holes on the device are designed
for heat dissipation to ensure that the device works normally. Do not cover
these heat dissipation holes.
Do not put this device close to a place where a heat source exits or high
temperature occurs.Avoid the device from direct sunshine.
Do not put this device close to a place where is over damp or watery. Do not
spill any fluid on this device.
Do not connect this device to any PC or electronic product, unless our
customer engineer or your broadband provider instructs you to do this,
because any wrong connection may cause any power or fire risk.
Do not place this device on an unstable surface or support.
1.5 LED Status Description
1.5.1 LED Status
Indicator
Status
Description
Power
Off
The power is off.
Green
The power is on and the device operates
normally.
Red
The power is self-testing.
The self-testing of the power fails if the
LED is always red.
Blink Red
Upgrading software.
DSL
Off
No signal is detected.
Blink Green
The DSL line is transferring.
Green
The DSL line connection is established.
Internet
Off
No internet connection.

4
Indicator
Status
Description
Blink Red
The DSL line tries to activate or fails to
activate.
Blink Green
Data is being transmitted through the
WAN interface.
Green
The connection is established. The users
can access the Internet.
LAN1/2/3/4
Off
No Ethernet signal is detected.
Blink Green
The user data is passing through
Ethernet port.
Green
Ethernet interface is ready to work
1.5.2 Rear Panel
Interface
Description
DSL
VDSL connector, for connecting to VDSL telephone line.
Reset
Keep power on, put a thin needle in-to the hole to press
the button for about 1 second, then the device restores to
the factory default configuration.
LAN1/2/3/4
LAN interface, for connecting to a computer or switch.
Power
Power supplied port, for connecting the power adapter.
The power adapter output is: 12 V DC, 2A.
Power switch.
2 Hardware Installation

5
The Router can be placed on a shelf or desktop, ideally you should be able to see
the LED indicators in the front, as you may need to view them for troubleshooting.
Place the DSL Router in a location where it can be connected to the various
devices as well as to a power source. The DSL Router should not be placed where
it is exposed to moisture or excessive heat. Ensure the cables and power cord are
placed safely to avoid tripping hazard. As with any electrical appliance, observe
common sense safety procedures.
2.1 Connecting the DSL Router
Step 1 See the following figure. Connect the DSL port of the Router with a telephone
cable.
Step 2 Connect the LAN port of the DSL Router to the network card of the PC via an
Ethernet cable.
Step 3 Plug one end of the power adapter to the wall outlet and connect the other
end to the Power port of the DSL Router.
The followig figure displays the connection of the DSL Router, PC, and telephones.
2.2 Factory Reset Button
The Router may be reset to the original factory default settings by depressing the
reset button for a few seconds while the device is powered on. Use a ballpoint or
paperclip to gently push down the reset button. Remember that this wipes out any
settings stored in the flash memory, including user account information and LAN IP

6
settings. The device settings are restored to the following factory defaults: the IP
address is 192.168.1.1, subnet mask is 255.255.255.0, user name for
management is admin, and password is admin.
3 PC Network Configuration
Each network interface on the PC should either be configured with a statically
defined IP address and DNS address, or be instructed to automatically obtain an IP
address using the network DHCP server. DSL router provides a DHCP server on
its LAN and it is recommended to configure your LAN to automatically obtain its IP
address and DNS server IP address.
The configuration principle is identical but should be carried out differently on each
operating system.
The following displays the TCP/IP Properties dialog box as it appears on Windows
XP.

7
Figure 1 IP and DNS configuration
TCP/IP configuration instructions for Windows XP are as follows.
Step 1 Choose Start > Control Panel > Access Network Connections from the
desktop.
Step 2 Right-click the Ethernet connection icon and choose Properties.
Step 3 On the General tab, select the Internet Protocol (TCP/IP) component
and click Properties.
Step 4 The Internet Protocol (TCP/IP) Properties window appears.
Step 5 Select the Obtain an IP address automatically radio button.
Step 6 Select the Obtain DNS server address automatically radio button.
Step 7 Click OK to save the settings.

8
4 Web-Based Management
Note:
This project is hardware project, the Web interface of software is for reference
only.
This chapter describes how to use Web-based management of the DSL router,
which allows you to configure and control all of DSL router features and system
parameters in a user-friendly GUI.
Figure 2 Web-based management - home page
4.1 Logging In to the Modem
The following description is a detail “How-To”user guide and is prepared for first
time users.
4.1.1 First-Time Login
When you log in to the DSL Router for the first time, the login wizard appears.

9
Step 1 Open a Web browser on your computer.
Step 2 Enter http://192.168.1.1 (default IP address of the DSL router) in the
address bar. The login page appears.
Step 3 Enter a user name and the password. The default username and
password of the super user are admin and admin. The username and
password of the common user are user and user. You need not enter the
username and password again if you select the option Remember my
password. It is recommended to change these default values after logging in
to the DSL router for the first time.
Step 4 Click OK to log in or click Cancel to exit the login page.
Figure 3 WBM login authentication
After logging in to the DSL router as a super user, you can query, configure, and
modify all configurations, and diagnose the system.
4.2 DSL Router Device Information
Choose Device Info, the following page appears.

10
Figure 4 Device Info menu
4.2.1 Summary of Device Information
Choose Device Info > Summary, the following page appears.
LAN IPv4 Address: the management IPv4 address.
Default Gateway: In the bridging mode there is no gateway. In other modes,
it is the address of the uplink equipment, for example, PPPoE/PPPoA.
DNS Server address: In the PPPoE/PPPoA mode, it is obtained from the
uplink equipment. In the bridging mode, there is no DNS Server address and
you can manually enter the information.
4.2.2 WAN Interface Information
Choose Device Info > WAN and the following page appears.

11
Description: Descripte this interface with protocol and PVC.
Type: The connection type of WAN, such as PPPoE, PPPoA.
4.2.3 Statistics
This page contains the following four parts:
Statistics of LAN
Statistics of WAN Service
Statistics of xTM
Statistics of xDSL
4.2.3.1 Statistics of LAN
Choose Device Info > Statistics > LAN and the following page appears. You can
query information of packets recevied at the Ethernet and USB interfaces. Click
Reset Statistics to restore the values to zero and recount them.
The LAN side interface includes Ethernet USB device.

12
Figure 5 Statistics of LAN
4.2.3.2 Statistics of WAN
Choose Device Info > Statistics > WAN Service and the following page appears.
You can query information of packets recevied by the WAN interfaces. Click Reset
Statistics to restore the values to zero and recount them.
Figure 6 Statistics of WAN
4.2.3.3 Statistics of XTM
Choose Device Info > Statistics > XTM and the following page appears. You can
query information of packets recevied by the XTM interfaces. Click Reset
Statistics to restore the values to zero and recount them.

13
Figure 7 Statistics of XTM
4.2.3.4 Statistics of xDSL
Choose Device Info > Statistics > xDSL and the following page appears.
If the DSL line is activated, the following window appears.

14
Traffic Type: ATM, or PTM.

15
Click Reset Statistics at the bottom to restore the values to zero and recount
them.
Click xDSL BER Test to test xDSL Bit Error Rate.
4.2.3.5 xDSL BER Test
Click xDSL BER Test to perform a bit error rate (BER) test on the DSL line. The
test page is as follows:
Figure 8 ADSL BER test
The Tested Time (sec) can be 1, 5, 10, 20, 60, 120, 180, 240, 300, or 360.
Note: If the BER reaches e-5, you cannot access the
Internet.
4.2.4 Route Table Information
Choose Device Info > Route and the following page appears.

16
Figure 9 Route table
4.2.5 ARP Table Information
Choose Device Info > ARP and the following page appears. You can query the
MAC and IP address information of the equipment attached to the modem.
Figure 10 ARP table
4.2.6 DHCP IP Lease Information
Choose Device Info > DHCP and the following page appears. You can query the
IP address assignment for MAC address at the LAN side of the DSL router and
obtain the IP Address from the DHCP server through Ethernet in the DSL router.
Figure 11 DHCP leases list
Expires In: Time that the device leases the IPAddress for the MAC Address.

17
4.3 Advanced Setup
Choose Advanced Setup > WAN Service and the submenus of WAN Service are
shown as below:
You can select one connection mode of the interface according to your ISP
instruction.
4.3.1.1 ADSL
After selecting the ADSL as the connection mode, click Next and the following
page appears.