Oway Segno User manual

Segno
CONFIGURATION,
USE AND
MAINTENANCE
MANUAL
Essential oil
electric diffuser

2
Table of contents
SECTION 1 ..................................................................................................4
DECLARATION OF CONFORMITY .............................................4
MANUFACTURER’S DATA .........................................................4
Authorized Assistance Service .....................................................4
PRESENTATION OF THE MANUAL............................................4
Conventions....................................................................................... 5
SECTION 2 ..................................................................................................6
WARRANTY................................................................................6
GENERAL SAFETY RULES........................................................7
Notice ................................................................................................. 7
Safety standards................................................................................ 8
DESCRIPTION ............................................................................8
TECHNICAL DATA......................................................................8
INTENDED USE ..........................................................................9
UNINTENDED USE .....................................................................9
RESIDUAL RISKS.......................................................................9
Operations which may cause risks for the user ............................... 10
SECTION 3 ..................................................................................................11
COMPONENTS ...........................................................................11
LOCATIONS................................................................................11
HANDLING .................................................................................11
PRELIMINARY CHECKS.............................................................11
Power supply ................................................................................... 12
USE.....................................................................................................12
Use procedures.................................................................................. 12
Troubleshooting................................................................................. 12

3
SECTION 4 ..................................................................................................13
MAINTENANCE ..........................................................................13
DECOMMISSIONING AND DISPOSAL .......................................13
Deactivation of the device ................................................................. 13
Disposal ............................................................................................. 14

4
SECTION 1
Declaration of conformity
Manufacturer’s Data
Presentation of the manual
DECLARATION OF CONFORMITY
The electric diffuser described in this documentation is sold accompanied by the de-
claration of conformity drawn up in accordance with applicable EU legislation.
MANUFACTURER’S DATA
Name of the Company Rolland S.r.l.
Head office Via Giuseppe di Vittorio 11 - Loc. Cadriano
- 40057 - Granarolo dell’Emilia (BO)
VAT number or Tax code 00820241206
Office Tel. no. [phone]
Fax. [phone]
E-mail [e-mail]
Website www.oway.it
Authorized Assistance Service:
The authorized assistance service on the product is performed directly by Rolland S.r.l.
PRESENTATION OF THE MANUAL
NOTE
ONCE YOU RECEIVE THE DEVICE, READ THIS MANUAL CAREFULLY
BEFORE CARRYING OUT ANY OPERATION.
This manual contains instructions for the configuration, use, and maintenance of the
SEGNO (BZ-KK1-1 model). The manual consists of various sections (each of which
deals with a series of topics) divided into chapters and paragraphs.

5
The general index lists all the topics covered in the entire manual. The numbering
of the pages is progressive, and each page features the number of the same. This
manual is intended for the user in charge of the configuration, use, and maintenance
of SEGNO, and it is related to the device’s technical life after its production and sale.
Before starting any operation, it is necessary to have at least read the entire
manual and then studied the operations to be performed.
This manual contains proprietary information and may not even be partially supplied to unau-
thorized third parties for any use and in any form without prior written consent of Rolland S.r.l.
Rolland S.r.l. states that the information contained in this manual is compliant with the technical
and safety specifications of SEGNO which the manual refers to.
A certified copy of this manual is stored in the device’s technical file, kept at Rolland S.r.l.’s
headquarters.
Rolland S.r.l. shall not recognize any document that has not been produced, released, or distri-
buted by itself or its authorized representative.
Conventions
In order to obtain a more immediate understanding of the topics, the graphic and typo-
graphic symbols and conventions described below are adopted in the manual.
DANGER OF ELECTROCUTION
AREA UNDER VOLTAGE
DANGER
DANGER SIGNALS INDICATE THOSE PROCEDURES WHICH TOTAL OR
PARTIAL NON-COMPLIANCE MAY CAUSE DAMAGE OR INJURY TO PEO-
PLE AND SERIOUS DAMAGE TO THE DEVICE.
NOTE
NOTES CONTAIN IMPORTANT INFORMATION, HIGHLIGHTED OUT-
SIDE THE TEXT TO WHICH THEY REFER
ATTENTION
WARNING SIGNALS INDICATE THOSE PROCEDURES WHOSE TOTAL OR
PARTIAL NON-COMPLIANCE MAY CAUSE DAMAGE TO THE DEVICE OR ITS
COMPONENTS, AND MAY EXPOSE PEOPLE TO DANGER.

6
SECTION 2
Warranty
General safety rules
Description and technical data
Intended and Unintended Use
Residual risks
WARRANTY
The warranty terms and conditions, which are listed in full in the purchase contract,
are valid only if the device is used in the conditions envisaged for the intended use.
Except for the operations described in the section labelled MAINTENANCE and
carried out according to the procedures indicated, any repair or modification made to
SEGNO by the user or by unauthorized companies will void the warranty.
The warranty does not extend to damage caused by inexperience or negligence in
the use of the device, or by poor maintenance, or omission thereof.
The warranty is valid subject to the following terms and conditions:
1For a period of 12 months from the date of purchase.
2Replacement may be made, at the company’s discretion, only after detailed
check and incorrect assembly/operation is found.
3Costs of transport and/or shipment for the repair or replacement of the device
shall in all cases be at the purchaser’s expense
4During the warranty period, any products replaced become the property of the ma-
nufacturer.
5The only beneciary of the warranty is the purchaser who has complied with the
instructions given in the manual.
6Company’s liability ceases when the buyer assigns ownership of the product or
modications have been made to same.
7The warranty does not include damage resulting from excessive stress, such as
the use of the product after discovering a fault, the use of improper operating
methods, or failure to observe the instructions for use and maintenance.
8The company accepts no liability for any difculties that may arise in the resale
or use abroad due to the applicable provisions in the country where the product
was sold.
9The defective product will not be replaced without proof of purchase (invoice,
copy of payment transaction).

7
Warning: if you intend to use the warranty, you must provide the following information:
1Batch
2Date of purchase (presentation of the purchase document)
3Detailed description of the problem
NOTE
FAILURE TO COMPLY WITH THE METHODS OF OPERATION AND USE
OF THE DEVICE DESCRIBED IN THIS DOCUMENTATION , WILL RESULT
IN THE LOSS OF WARRANTY.
GENERAL SAFETY RULES
Notice
Please check that all the items listed in the COMPONENTS section are included in the
product packaging and inform Rolland S.r.l. immediately of any components missing or
documents which are illegible (even if only in part).
This chapter describes the general safety rules to be observed during any operation per-
formed with the device. Operation procedures described in the following chapters must
be performed by observing both the methods to be followed provided for in the instruc-
tions, and the general safety rules of this chapter.
The safety rules, use and maintenance procedures indicated in this document
are complementary to the general safety rules at workplace that must be ob-
served.
Different countries may have different safety regulations. Please note therefore that in all
cases where the documentation conict with or are more restricted than the standards of
the country in which SEGNO is used, the national standards of that country shall prevail
over those of the documentation.
NOTE
THE MANUFACTURER MAY UNDER NO CIRCUMSTANCES BE HELD
LIABLE FOR ACCIDENTS OR CONSEQUENTIAL DAMAGES FOR INAP-
PROPRIATE USE OF THE DEVICE OR FOR FAILURE TO COMPLY, EVEN
IN PART, WITH THE OPERATIONAL SAFETY RULES AND PROCEDU-
RES DESCRIBED IN THE DOCUMENTATION.
Failure to comply with the instructions for its use and the methods of operation, congu-
ration, use and maintenance of SEGNO contained in the manual shall also result in the
voiding of terms and conditions of warranty.

8
Safety standards
During the use of SEGNO there may occur situations in which the device does not
function correctly or in ways not envisaged in the documentation. These situations,
which are completely abnormal, may sometimes be caused by environmental factors
or accidental failures which could not have been anticipated by the manufacturer. We
suggest keeping a spare copy of the manual at the disposal of the user and/or of the
staff in charge of the management, maintenance, and use of SEGNO.
ATTENTION
SINCE IT WOULD BE IMPOSSIBLE TO DESCRIBE EVERY OPERATION
THAT SHOULD NOT OR CANNOT BE DONE, IT IS HEREBY DEEMED
THAT ANY OPERATION (OTHER THAN FOR NORMAL USE) THAT IS
NOT EXPRESSLY DESCRIBED IN THE MANUAL PROVIDED IS TO BE
CONSIDERED AS ONE WHICH SHOULD NOT OR CANNOT BE DONE.
DESCRIPTION
The device covered by this document (SEGNO) is an electric diffuser which
allows nebulising pure essential oils in the environment. The electric motor in-
side the wooden base generates an air flow which, passing through the dome,
mixes the essential oils this contains with the flow and spreads the solution
into the environment through the hole in the glass stopper. The glass stopper
closes the opening on the top of the dome, an opening through which the
product can be loaded. It is possible to adjust the diffusion intensity using the
metal knob/potentiometer placed on the wooden base of the diffuser which also
acts as a switch. The device is connected to the mains through a USB - USB C
cable which is in turn connected to a power supply unit.
Mechanical data
Overall dimensions 24 x 14,5 x 12 cm
Weight 500 gr
External material Painted pine wood, metal, glass, felt
Electrical data
Power supply Input: AC 100-240 V; 50/60Hz; 0.45A
Output: DC 5 V; 1000mA
Power 3 W
TECHNICAL DATA

9
INTENDED USE
SEGNO is an electric essence diffuser intended for home use and for beauty and hair-
dressing salons in order to perfume environments by spraying a mist of pure essential
oils. The device can only be used with pure essential oils.
UNINTENDED USE
There is no use other than those described in the paragraph titled DESCRIPTION and
INTENDED USE.
It is also absolutely prohibited:
• To use the device with non-compliant power lines.
• To use the device for applications different from those indicated.
• To modify the device (hardware and rmware)
The reuse of any unit after the device has been taken out of service releases the manu-
facturer from any liability deriving from its use.
NOTE
THE MANUFACTURER CANNOT BE HELD IN ANY CASE RESPON-
SIBLE FOR ACCIDENTS OR DAMAGE ARISING FROM THE UNIN-
TENDED USE OF THE DEVICE. MOREOVER, ANY UNINTENDED USE
ALSO CAUSES THE TERMINATION OF THE WARRANTY PERIOD.
RESIDUAL RISKS
Rolland S.r.l. carried out an in-depth risk analysis on the device in question du-
ring the design phase.
This analysis revealed risks that cannot be eliminated due to their nature. These
risks were then examined individually and the instructions on how to avoid them
were emphasized in this manual. It is therefore important that any user in charge of
configuration, use, and maintenance of the SEGNO has previously read the manual.
NOTE
THE MANUFACTURER CANNOT BE HELD IN ANY CASE RESPON-
SIBLE FOR ACCIDENTS OR DAMAGE ARISING FROM THE UNIN-
TENDED USE OF THE DEVICE CAUSED BY NEGLIGENCE ON THE
PART OF THE USER.

10
In particular:
• It is absolutely forbidden to make any changes to the device. Any damage to peo-
ple, animals, or things resulting from the use of the device improperly modified by an
unauthorized operator shall relieve the manufacturer of all responsibility.
• Carefully keep a copy of this manual, which is necessary for the correct and safe
use of SEGNO.
• Should the external structure have sharp edges due to accidental impact such as
to make it dangerous, it is necessary to contact Rolland S.r.l..
Important:
- Do not wet the electrical connections and the electric diffuser with water or other
liquids.
- The maintenance operations described in the manual must be carried out.
- Maintenance operations must be done following the instructions described this
manual.
Operations which may cause risks for the user:
During start-up operations, follow the general accident prevention regulations.
In particular:
- if working on electrical parts, make sure they are not live.
Already during the design phase, solutions have been adopted aimed at making the
use of the device safe in all phases of use: transport, assembly, adjustment, use, and
maintenance. Nevertheless, not all possible risks for either users or the environment
have been eliminated, both for technological reasons (device reliability) and for ma-
nagement reasons (excessive difculty); consequently, the residual risks present are
reported in the manual.