Owon SES441 User manual

1
SES441 ZigBee Wall Switch
Quick Start Guide

2
WARNING: Failure to follow these safety notices could result in 󽗉re,
electric shock, other injuries, or damage to the smart energy switch
and other property. Read all the safety notices below before using
the ZigBee Wall Switch.
• Avoid high humidity or extreme temperatures.
• Avoid long exposure to direct sunlight or strong ultraviolet light.
• Do not drop or expose the unit to intense vibration.
• Do not disassemble or try to repair the unit on your own.
• Do not expose the unit or its accessories to 󽗊ammable liquids, gases
or other explosives.
Safety Handling

3
Technical Speci󽗉cations
Wireless Connectivity
ZigBee • 2.4GHz IEEE 802.15.4
ZigBee Pro󽗉le • ZigBee 3.0
RF Characteristics
• Operating frequency: 2.4GHz
• Range outdoor/indoor: 100m /
30m
Physical Speci󽗉cations
Button • Touch Screen
Relay • Neutral and live wire double break
Operating Voltage • 100~240 Vac 50/60 Hz
Calibrated Metering Accuracy • ≤ 100W ( Within ±2W )
• >100W ( Within ±2% )
Max. Load Current • 20 A
Operating environment • Temperature: -20℃ ~+55℃
• Humidity: ≤ 90% non-condensing
Dimensions • 86 (L) x 86(W) x32(H) mm
Weight • 132g
Mounting Type • In-wall mounting

4
The ZigBee Wall Switch SES441 is a device with wattage (W) and
kilowatt hours (kWh) measurement functions. It allows you to control
its On/O󽗈 status as well as to check real-time energy usage wirelessly
via your mobile App.The relay is designed with double-break mode.
The switch is suitable for power control of air conditioner and water
heater.
This guide will provide you with an overview of the product and help
you get through the initial setup.
Note: Use the smart energy switch for no more than rated current 20A.
• ZigBee 3.0
• Relay with double-break mode
• Control your home device via Mobile APP
• Energy consumption measuring
• Extend the range and strengthen ZigBee network communication
• Compatible with hot water, air conditioner's power supply
Features:
Welcome
1

5
Important safety information!
• The ZigBee Wall Switch must be installed and serviced only by
quali󽗉ed electrical personnel.
• Do not touch the terminals of the device during the testing.
• Turn o󽗈 all power supplying this equipment before installing.
• Make sure that the power supply is off before connecting or
disconnecting it to the auxiliary device.
• Always use a properly rated voltage sensing device to con󽗉rm power
is o󽗈.
• Replace all devices, doors and covers before turning on power to
this equipment.
Failure to follow these instructions will result in death or serious
injury.
1 Turn off all power supplying, then use a screwdriver in the
direction shown below to remove the switch panel from the top.
Installation
2

6
On/O󽗈 button & LED indicator
2 Follow the wiring diagram for wiring.
3 Fix the switch to the wall with screws, close the panel, and then
turn on the power.
N
IN IN
OUT OUT
L LN
Wiring Diagram
Get to know your device
3

7
Reset:
ON/OFF button
Tap on/o󽗈 button once to control the device.
LED status What it means
Green The load is ON.
Red The load is OFF.
Steady light Device has joined a ZigBee network.
Flashing slowly(0.5s On, 2.5s
O󽗈)
Device has not joined a ZigBee
network.
Flashing rapidly(0.5s On/O󽗈) Identify mode.
LED indicator
The LED status gives the following information:
Reset procedure allows to restore the device back to its factory settings,
which means all information and user con󽗉guration (Including energy
data)will be deleted.
1. Press the on/o󽗈 button 3 times continuously, hold at the third time,
and release until the light starts to 󽗊ash.
2. Wait for a while, when the light turns red 󽗊ashing, it means that the
device has been reset to factory settings.

8
4.1 To get started, you will need:
• A Zigbee Gateway.
• A mobile phone with a mobile APP installed.
4.2 Adding to the gateway's network
1. Set your gateway to permit joining(see your gateway's manual).
2. Power on the smart switch and make sure the LED indicator is
󽗊ashing slowly (If not, reset it to factory defaults).
3. After few seconds the smart switch will join the gateway
automatically and the LED indicator will become steady when
successfully joined.
Note: If the smart switch fails to join the gateway's network within one
minute, simply reset the smart switch and retry.
5FAQ
Q 1. Can the smart energy switch SES441 pair with SLC602 remote
switch? Yes, you can refer to SLC602 guide to pair with it.
Q 2. How to clear the accumulative power consumption of the smart
energy switch?
Way 1：Login the relative gateway on your app, enter the edit mode
, then click the clear accumulative power consumption button(arrow
icon).
Way 2：Reset the smart energy switch to factory default setting. Note:
This way will lead the device lost connection of internet, you need to
reconnect the gateway internet to use it.
Con󽗉gure Network
4