Owon SLC600-R User manual

1
SLC600-R Remote Control Switch
Quick Start Guide

2
WARNING: Failure to follow these safety notices could result in 󽗉re,
electric shock, other injuries, or damage to the Remote Control
Switch and other property. Read all the safety notices below before
using the Remote Control Switch.
• Avoid high humidity or extreme temperatures.
• Avoid long exposure to direct sunlight or strong ultraviolet light.
• Do not drop or expose the unit to intense vibration.
• Do not disassemble or try to repair the unit on your own.
• Do not expose the unit or its accessories to 󽗊ammable liquids, gases
or other explosives.
Safety Handling

3
Wireless Connectivity
ZigBee • 2.4GHz IEEE 802.15.4
ZigBee Pro󽗉le • ZigBee 3.0
RF Characteristics
• Operating frequency: 2.4GHz
• Range outdoor/indoor: 100m /
30m
• Internal PCB Antenna
• TX Power: 19DB
Physical Speci󽗉cations
Operating Voltage • 100~250 Vac 50/60 Hz
Flame Rating • V0
Power consumption • < 1W
Operating environment
• Indoor
• Temperature: -20° C ~ +50° C
• Humidity: ≤ 90% non-condensing
Dimensions
• 86 Type Wire Junction Box
• Product size: 92(L) x 92(W) x
35.4(H) mm
• In-wall size: 63.3(L) x 61.9(W) x
22.4(D) mm
• Thickness of front panel: 13mm
Technical Speci󽗉cations

4
Compatible system • 3-wire Lighting Systems
Weight • 145g
Mounting Type • In-wall mounting
• CN standard

5
The Remote Control Switch SLC600-R is designed to control your
device On/O󽗈. You can bind with multiple devices and control them at
the same time.
This guide will provide you with an overview of the product and help
you get through the initial setup.
• ZigBee 3.0 compliant
• Works with any standard ZigBee Hub
• Bind with multiple devices
• Control multiple devices at the same time
• Supports up to 9 devices to bind (All gang)
Features:
Welcome
1

6
Important safety information!
• The Remote Control Switch must be installed and serviced only by
quali󽗉ed electrical personnel.
• Do not touch the terminals of the device during the testing.
• Turn o󽗈 all power supplying this equipment before installing.
• Make sure that the power supply is off before connecting or
disconnecting it to the auxiliary device.
• Always use a properly rated voltage sensing device to con󽗉rm power
is o󽗈.
• Replace all devices, doors and covers before turning on power to
this equipment.
Failure to follow these instructions will result in death or serious
injury.
Installation
2
Turn o󽗈 all power supplying and remove the switch panel.
Get started:
1

7
Wiring Diagram
Follow the wiring diagram for wiring.
2
Fix the switch to the wall with screws, close the panel.
3
IN
IN
L
N

8
Reset:
LED status What it means
Flashing slowly Enable to join a ZigBee network.
When you press any button
Flashing rapidly for 3 times Device has not joined a ZigBee
network.
Flashing rapidly for 1 time Device has joined a ZigBee network/
Trigger the button.
LED indicator
The LED status gives the following information:
1. Press one of the On/Off button for 4 times continuously, hold at
the fourth time for ten seconds until the LED light 󽗊ashes rapidly for
3 times at 󽗉fth second, and 󽗊ashing rapidly for 3 times again at tenth
second.
2. Wait for a while, when the light turns 󽗊ashing slowly, it means that
the device has been reset to factory settings and enable to join a
ZigBee network. It will automatically exit the mode after 90 seconds
and the lED light will turn to steady.
Get to know your device
3
On/O󽗈 button1 & LED indicator On/O󽗈 button2 & LED indicator

9
4.1 To get started, you will need:
• A Zigbee Gateway.
• A mobile phone with a mobile APP installed.
4.2 Adding to the gateway's network
1. Set your gateway to permit joining (see your gateway's manual).
2. Power on the Remote Control Switch and make sure the LED
indicator is 󽗊ashing slowly (If not, reset it to factory defaults).
3. After a few seconds the Remote Control Switch will join the gateway
automatically and the LED indicator will become steady. Press any
button to check if the LED status flashes rapidly for 1 time, which
means it has joined successfully.
Note: If the Remote Control Switch failed to join the gateway's
network within 90 seconds, simply reset the Remote Control Switch
and retry.
Con󽗉gure Network
4
4.3 Pair the Remote Control Switch with other device
Note: Please make sure the device is added into the same network
of the gateway and it can be controlled by the mobile app before you
proceed.
1. Power on your devices.
2. Enable your device into identify mode. Your device will 󽗊ash during
the identify process.
3.Place your device near the Remote Control Switch. Choose one gang,
then press and hold one of the On/O󽗈 button for 8 seconds until the
LED indicator 󽗊ashes rapidly for 3 times.
4.Your bound device will stop 󽗊ashing when pairing successfully.

10
Tip: If pairing failed, you need to repeat the above process and try it
again.
5.Now you are able to control your device by using the gang.
You can also follow the steps above to bind the other gang with the
device which has on/off functions, such as power relay, smart plug,
etc.