Owon SLC603 User manual

SLC603 ZigBee Dimmer Switch
Quick Start Guide

2
1. Introduction
The SLC603 ZigBee Dimmer Switch is designed to control the
following features of a CCT Tunable LED bulb:
Turn on/off the LED bulb
Adjust the brightness of the LED bulb
Adjust the color temperature of the LED bulb
2. Get to know your device
2.1. SLC603 at a glance
Rotary button
Brightness/
color temperature
switch

3
Release Catch
Reset button & LED indicator

4
2.2. Buttons Introduction
Rotary button
Turn ON and OFF the LED bulb.
Adjust the brightness of the LED bulb.
Adjust the color temperature of the LED bulb.
Reset button
Return the device to default factory settings by pressing the reset
button for 10 seconds (the LED indicator will flash 3 times in three
seconds and flash again 3 times in 10 seconds)
Set the device into pairing mode to pair with an LED bulb by
pressing the reset button for 3 seconds (the LED indicator will
flash 3 times)
Release Catch
Push and turn in the direction of the arrow to remove from the
back plate. This will allow battery fitment and replacement.
Color Temperature/Brightness selector switch
Select color temperature adjustment
Select brightness adjustment

5
LED Indicator
Please refer to the table below for LED status information:
LED Status
What it means
Red light flashing
Device has not joined a network
Green light flashing
three times
Device in pairing mode or pairing success
No light
Device is in a network

6
3. Get started
To get started, you will need:
A Smart Gateway
A LED622 ZigBee CCT Tunable LED bulb
A SLC603 ZigBee Dimmer Switch
The mobile app
Then follow the steps below:
Step 1: Install the batteries
Remove the device from its back plates as described previously, fit
the batteries and re-assemble.
Step 2: Check the switch status
Press the rotary button and check if the LED indicator light is flashing
red.
Tip: if not, please return it to default factory settings by using a pin
key tool to press and hold the reset button for ten seconds (the LED
indicator will flash 3 times in three seconds and flash again 3 times
in 10 seconds).

7
Step 3: Select “Add new devices” in the menu of the app.
Tip: for this step, you could also press the “Z” button of the gateway
for two seconds until the LED indicator turns solid blue.
Step 4: Use a pin key tool to press the reset button. Then the SLC603
Dimmer Switch will try to join the gateway based system.
Step 5: Check if the SLC603 Dimmer Switch is added into the
gateway.

8
When the SLC603 Dimmer Switch is added into the gateway, press
the rotary button and be sure the LED indicator does not flash.
Tip: If the LED is still flashing, it means that the SLC603 Dimmer
Switch hasn’t added into the gateway. You will need to reset the
device to default factory setting and repeat the process from step 2.
Step 6: Bind with the CCT Tunable LED bulb LED622
Note: please make sure the LED622 is also added into the same
gateway based system and can be controlled by the mobile app
before you continue.
(1) Make sure the LED bulb is powered on.
(2) Go to the “Lighting” section, tap “Edit” (Android phone) or swipe
from right to left (iPhone), tap “Identify”. The LED bulb will flash
during the “Identify” process.

9
(3) Press and hold the reset button of the SLC603 Dimmer Switch for
three seconds (the LED indicator will flash 3 times) and it will search
for pairing device.
(4) After the pairing is successful, the LED indicator of the SLC603
Dimmer Switch will flash three times, and the LED bulb will also stop
flashing.
You are now able to control the LED bulb using the SLC603 Dimmer
Switch.

10
4. FAQ
Q1. How can I return this device to default factory settings?
A1: Please use a pin key tool to press and hold the reset button for
ten seconds (the LED indicator will flash 3 times in three seconds
and flash again 3 times in 10 seconds).

11
5. Technical Specifications
Wireless Connectivity
ZigBee 2.4GHz IEEE 802.15.4
RF Characteristics
Operating frequency: 2.4GHz
Range outdoor/indoor: 100m/30m
Internal PCB antenna
ZigBee Profile
ZigBee Lighting Link Profile
Battery
Type: 2 x AAA batteries
Voltage: 3V
Battery Life: 1 year
Dimensions
Diameter: 90.2mm
Thickness: 26.4mm
Weight
66 g

12
6. Safety Notice
WARNING: Failure to follow these safety notices could
result in fire, electric shock, other injuries, or damage to
the device or other property. Read all the safety notices
below before using the device.
Avoid high humidity or extreme temperatures.
Avoid long exposure to direct sunlight or strong ultraviolet light.
Do not drop or expose the unit to intense vibration.
Do not disassemble or try to repair the unit yourself.
Do not expose the unit or its accessories to flammable liquids,
gases or other explosives.