OXFORD BABY 10513 User manual

ASSEMBLY INSTRUCTIONS
for convertible crib
HOLLAND ISLAND 3 IN 1 ACRYLIC CRIB
Model #10513
GUARDRAIL sold separately.
Please contact retailer
THIS PRODUCT CONFORMS TO THE APPLICABLE SECTION OF PUBLIC LAW 110-314
AND COMPLIES WITH THE REQUIREMENTS STATED IN 16 CFR 1219 AND 16 CFR 1217
(WHEN HOLLAND GUARDRAIL IS USED).
1 of 5
10-10513-V-01

Thank you for your purchase!
Remove all parts and hardware from the box and lay on a carpeted or scratch -free work surface.
Do not dispose of any contents until assembly is completed.
Familiarize yourself with all exhibits and diagrams to facilitate the assembly of your crib.
TOOLS REQUIRED:
ALLEN KEY (Included)
Do not fully tighten all bolts until all parts are in place.
(please add an extra 1/2 revolution to the bolts when using spring washer after tightening)
PARTS ENCLOSED IN CARTON
A. Headboard/Footboard (2 pcs) B. Sideboard (2 pcs)
E. Mattress Spring (1 pc)
2 of 5
10-10513-V-01
HARDWARE
(F) Allen bolt 2" (50 mm) (8 pcs)
(G) Allen bolt 1"(25mm) (4 pcs)
(W) Spring washer (8 pcs)
(H) Nut 3/4" (20mm) (4 pcs)
(L) Half moon washer (4 pcs)
(M) Allen key (2 pcs) (length may vary)
D. Stabilizer bar (1 pc)

STEP 1 " ASSEMBLY OF SIDEBOARD"
THIS STEP REQUIRES :
A. Headboard/Footboard (1 pc)
B. Sideboard (2 pcs)
F. Allenbolt 2" (50 mm) (4 pcs)
W. Spring washer (2 pcs)
3 of 5
10-10513-V-01
STEP 1
M. Allen key (1 pc)
B
F
W
M
B
A
F
L
M
STEP 1:
- Attach Sideboard (B) to the end of Headboard/footboard (A).
- Insert Allen bolt (F), Spring washer (W) through the upper holes of sideboards as FIG. 1.
- Insert Allen bolt (F), Half moon washer (L) through the lower holes of sideboards as FIG. 2.
- Tighten all bolts with Allen key (M).
FIG. 1
FIG. 2
L. Half moon washer (2 pcs)
RIGHT
INSIDE
FACE
INSIDE

STEP 2:
- Attach headboard/footboard (A) to sideboard.
- Insert Allen bolt (F), Spring washer (W) through the upper holes of sideboards as FIG. 3.
- Insert Allen bolt (F), Half moon washer (L) through the lower holes of sideboards as FIG. 4.
- Tighten all bolts with Allen key (M).
STEP 2 " ASSEMBLY OF SIDEBOARD "
THIS STEP REQUIRES:
A. Headboard/Footboard (1 pc)
4 of 5
10-10513-V-01
STEP 2
A
FIG. 3
FIG. 4
F
W
M
F
L
M
F. Allenbolt 2" (50 mm) (4 pcs)
W. Spring washer (2 pcs)
M. Allen key (1 pc) L. Half moon washer (2 pcs)

STEP 3 " MATTRESS OF SPRING INSTALLATION "
THIS STEP REQUIRES:
E. Mattress spring (1 pc)
M. Allen key (2 pcs)
G. Allenbolt 1" (25 mm) (4 pcs)
W. Spring washer (4 pcs)
5 of 5
10-10513-V-01
STEP 3:
- Attach Mattress spring (E) to Sideboard as shown in FIG.5.
- Secure with Allen key (M).
- See FIG.6. for height adjustment
- Make sure the Mattress Spring (E) is leveled after assembly.
FIG. 5
FIG. 6
Lowest
position
Highest
position
Middle
position
Lowest
position
M
G
WH
M
G
WH
E
H. Nut 3/4" (20mm) (4 pcs)
STEP 3
FACE
TOP

ASSEMBLY INSTRUCTIONS
for toddler bed
HOLLAND ISLAND 3 IN 1 ACRYLIC CRIB
Model #10513
GUARDRAIL sold separately.
Please contact retailer.
10-10513-V-01
1 of 4
GUARDRAIL sold separately.
Please contact retailer.

STEP 1 " UNINSTALL FOOTBOARD "
THIS STEP REQUIRES:
10-10513-V-01 2 of 4
Allen key (1 pc)
STEP 1
STEP 1:
Remove 1pc of headboard/footboard by unscrewing Allen bolts as shown in FIG. 1 and FIG. 2.
FIG. 2
FIG. 1
FIG. 2
RIGHT
INSIDE

STEP 2 " ASSEMBLY OF STABILIZER BAR "
THIS STEP REQUIRES:
D. Stabilizer bar (1 pc)
M. Allen key (1 pc)
3 of 4
10-10513-V-01
F. Allen bolt 2" (50 mm) (2 pcs)
L. Half moon washer (2 pcs)
STEP 2
STEP 2:
- Attach Stabilizer bar (D) to the side where removed headboard/footboard.
- Insert Allen bolt (F), Half moon washer (L) through the holes of stabilizer bar as shown in FIG. 3.
- Tighten all bolts with Allen key (M).
D
FIG. 3
These hardware are included in the CRIB
M
F
L

STEP 3 " MATTRESS SPRING ADJUSTMENT"
THIS STEP REQUIRES:
10-10513-V-01 4 of 4
G. Allenbolt 1" (25 mm) (4 pcs)
W. Spring washer (4 pcs) H. Nut 3/4" (20mm) (4 pcs)
Mattress spring (1 pc)
M. Allen key (2 pcs)
STEP 3:
- Remove the Allen bolt 1"(25 mm) (G), Spring Washer (W) and Nut 3/4"(20 mm)(H) on
the Mattress spring.
- Move Mattress spring to the lowest position as shown in FIG.4.
- Attach the Allen bolt 1"(25 mm)(G), Spring washer (W) and Nut 3/4"(20 mm)(H) on the
lowest hole of Sideboard.
- Final position as shown in FIG.5.
FIG. 4
Lowest
position
M
G
WH
These hardware are included in the CRIB
FIG. 5
STEP 3