Oypla GARDEN 3053 User manual

Page 1
Manual Version: v1.0
Model Code: 3053
Oypla.com LLP / www.oypla.com
User Manual
Model Code: 3053
Contents
1Front Cover
-
2Safety
Instructions
-
2Warning
Instructions
-
3Assembly
Instructions
-
8 Back Cover
End
Heavy Duty
Gardening Trolley

Page 2
Manual Version: v1.0
Model Code: 3053
Oypla.com LLP / www.oypla.com
Contents
1Front Cover
-
2Safety
Instructions
-
2Warning
Instructions
-
3Assembly
Instructions
-
8 Back Cover
End
Safety Instructions
Notice: Ensure you read and fully understand instructions before use
While every attempt is made to ensure the highest degree of protection in all equipment, we cannot
guarantee freedom from injury. The user assumes all risk of injury due to use. All merchandise is sold
on this condition, which no representative of the company can waive or change.
This product is not a toy, and is only to
be used for its designated purpose.
This product is intended for outdoor use
only.
Do not carry out alterations or
modifications to this product.
Clean only with a damp cloth. Do not use
strong industrial cleaning substances.
Leaving the product outside exposed to
weather, especially direct sun, rain and
salt air, will speed the weathering
process. This can be slowed by removing
the product from these conditions, or
covering it with a suitable cover.
Do not fill the tires with too much air as
this may cause for them to become
damaged due to the density.
Before using the product, make sure all
the fastenings are tightly in place and
that everything is in order, and checked
periodically by an adult.
The maximum weight capacity is 400kg.
Do not exceed this.
Ensure the load is evenly spread.
Don’t turn too quickly as this may cause
the load to become unsafe and fall out.
Don’t pull the trolley off of curbs or other
elevated places as this may damage the
load and/or the trolley. Use a ramp
where possible.
If the product is damaged or has any
defects, please contact
[email protected].
⚠The maximum weight capacity is
400kg. Do not overload this as it can cause
product failure and/or personal injury.
⚠
Warnings

Page 3
Manual Version: v1.0
Model Code: 3053
Oypla.com LLP / www.oypla.com
Parts List:
-If you are missing any of the below parts, please contact [email protected]
-Please be aware that you will be referring to this parts list throughout the assembly
process.
Contents
1Front Cover
-
2Safety
Instructions
-
2Warning
Instructions
-
3Assembly
Instructions
-
8 Back Cover
End
Assembly Instructions

Page 4
Manual Version: v1.0
Model Code: 3053
Oypla.com LLP / www.oypla.com
1
2
Contents
1Front Cover
-
2Safety
Instructions
-
2Warning
Instructions
-
3Assembly
Instructions
-
8 Back Cover
End
Part 2
Part 3
Part 1
Part 4
Place the handle beam (part 1) on
top of the handle beam axle (part
2), ensuring that the handle beam
(part 1) is as far down as possible.
This should leave a section of the
handle beam axle (part 2) exposed.
Slide the handle beam washer (part
3) onto the exposed section of the
handle beam axle (part 2). Secure
these in place with a securing pin
(part 4). Please see the images to
help.
Part 6
Part 1
Part 5
Part 8
Part 7
Slide the handle beam (part 1) onto
the trolley platform (part 5) so that
it aligns with either group of holes in
the bottom of the trolley platform
(part 5). Once done, hold the handle
beam (part 1) in place using a trolley
support bolt (part 6) and secure this
in place with a support washer (part
7) and a support nut (part 8).
Repeat for the other holes. Please
see the images to help.

Page 5
Manual Version: v1.0
Model Code: 3053
Oypla.com LLP / www.oypla.com
Part 7
Part 8
Part 6
Part 9
Part 11
Part 4
Part 10
Part 2/9
3
4
Contents
1Front Cover
-
2Safety
Instructions
-
2Warning
Instructions
-
3Assembly
Instructions
-
8 Back Cover
End
Slide the rear axle (part 9) onto the other set of holes. As with the handle beam,
secure these in place using the trolley support bolts (part 6), support nuts (part 7) and
support washers (part 8). Repeat for the other holes. Please see the image above.
Push a wheel (part 10) onto either the handle beam
axle (part 2) or the rear axle (part 9), then slide a
wheel washer (part 11) onto either axle and secure
both the wheel (part 10) and the wheel washer (part
11) into place with a securing pin (part 4). Repeat this
step on the opposite side and the remaining axle to
complete the wheels. Please see the images.

Page 6
Manual Version: v1.0
Model Code: 3053
Oypla.com LLP / www.oypla.com
Part 12
Part 13
5
Contents
1Front Cover
-
2Safety
Instructions
-
2Warning
Instructions
-
3Assembly
Instructions
-
8 Back Cover
End
Align the metal tube on the bottom of the platform side panel (part 12)
with the metal tube on the trolley platform (part 5), securing this in place
with a hitch pin (part 13). Repeat this on the other side of the platform
side panel (part 12) to complete this side and repeat this process on the
opposite side of the trolley platform (part 5) to complete both sides.
Please see the image for guidance.
6
Part 13
Part 14
Align the metal tube on the bottom of the trolley platform front panel
(part 14) with the metal tube on the trolley platform (part 5), securing
this in place with a hitch pin (part 13). Repeat this on the other side of
the platform front panel (part 14) to complete this side and repeat on
the opposite side of the platform (part 5) to complete both sides. Please
see the image for guidance.

Page 7
Manual Version: v1.0
Model Code: 3053
Oypla.com LLP / www.oypla.com
Contents
1Front Cover
-
2Safety
Instructions
-
2Warning
Instructions
-
3Assembly
Instructions
-
8 Back Cover
End
7
Part 17
Part 16
Part 15
Part 8
Part 7
Slide the handle (part 15) into
the handle rotation pod (part
16), making sure the holes in
both parts are aligned. After
this. Push the handle support
bolt (part 17) through both
parts, holding them into place.
Secure these with a support nut
(part 7) and a support washer
(part 8).
Once completed, ensure that all the support nuts (part 8) are tightened so the parts are
secure and won’t fall off over time and that the securing pins (part 4) are all bent to
ensure that the wheels won’t fall off when using the Heavy Duty Garden Trolley. Make
sure to pump the wheels (part 10) up before use so that when transporting heavy loads
in the Heavy Duty Garden Trolley the wheels don’t become worn at a faster rate. Do
not over fill the wheels as this may cause them to become too dense and more likely to
burst.

Page 8
Manual Version: v1.0
Model Code: 3053
Oypla.com LLP / www.oypla.com
Contents
1Front Cover
-
2Safety
Instructions
-
2Warning
Instructions
-
3Assembly
Instructions
-
8 Back Cover
End