Ozito GGM-010U User manual

1
GLUE GUN
10W
2 3 4 5 6 7
WARNING! Read all safety warnings and all instructions. Failure to
follow the warnings and instructions may result in electric shock, re and/
or serious injury.
Save all warnings and instructions for future reference. The term “power
tool” in the warnings refers to your mains-operated (corded) power tool or
battery-operated (cordless) power tool.
1. Work area safety
a. Keep work area clean and well lit. Cluttered or dark areas invite accidents.
b. Do not operate power tools in explosive atmospheres, such as in the
presence of ammable liquids, gases or dust. Power tools create sparks
which may ignite the dust or fumes.
c. Keep children and bystanders away while operating a power tool.
Distractions can cause you to lose control.
2. Electrical safety
a. Power tool plugs must match the outlet. Never modify the plug in any
way. Do not use any adapter plugs with earthed (grounded) power tools.
Unmodied plugs and matching outlets will reduce risk of electric shock.
b. Avoid body contact with earthed or grounded surfaces, such as pipes,
radiators, ranges and refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
c. Do not expose power tools to rain or wet conditions. Water entering a
power tool will increase the risk of electric shock.
d. Do not abuse the cord. Never use the cord for carrying, pulling or
unplugging the power tool. Keep cord away from heat, oil, sharp edges
or moving parts. Damaged or entangled cords increase the risk of electric
shock.
e. When operating a power tool outdoors, use an extension cord suitable
for outdoor use. Use of a cord suitable for outdoor use reduces the risk of
electric shock.
f. If operating a power tool in a damp location is unavoidable, use a
residual current device (RCD) protected supply. Use of an RCD reduces
the risk of electric shock.
3. Personal safety
a. Stay alert, watch what you are doing and use common sense when
operating a power tool. Do not use a power tool while you are tired
or under the inuence of drugs, alcohol or medication. A moment of
inattention while operating power tools may result in serious personal injury.
b. Use personal protective equipment. Always wear eye protection.
Protective equipment such as dust mask, non-skid safety shoes, hard hat, or
hearing protection used for appropriate conditions will reduce personal injuries.
c. Prevent unintentional starting. Ensure the switch is in the off-position
before connecting to power source and/or battery pack, picking up or
carrying the tool. Carrying power tools with your nger on the switch or
energising power tools that have the switch on invites accidents.
d. Do not overreach. Keep proper footing and balance at all times. This
enables better control of the power tool in unexpected situations.
e. Dress properly. Do not wear loose clothing or jewellery. Keep your hair,
clothing and gloves away from moving parts. Loose clothes, jewellery or
long hair can be caught in moving parts.
4. Power tool use and care
a. Do not force the power tool. Use the correct power tool for your
application. The correct power tool will do the job better and safer at the rate
for which it was designed.
b. Do not use the power tool if the switch does not turn it on and off. Any
power tool that cannot be controlled with the switch is dangerous and must be
repaired.
c. Disconnect the plug from the power source and/or the battery pack from
the power tool before making any adjustments, changing accessories,
or storing power tools. Such preventive safety measures reduce the risk of
starting the power tool accidentally.
d. Store idle power tools out of the reach of children and do not allow
persons unfamiliar with the power tool or these instructions to operate
the power tool. Power tools are dangerous in the hands of untrained users.
e. Maintain power tools. Check for misalignment or binding of moving
parts, breakage of parts and any other condition that may affect the
power tool’s operation. If damaged, have the power tool repaired before
use. Many accidents are caused by poorly maintained power tools.
f. Use the power tool, accessories and tool bits etc. in accordance with
these instructions, taking into account the working conditions and the
work to be performed. Use of the power tool for operations different from
those intended could result in a hazardous situation.
5. Service
a. Have your power tool serviced by a qualied repair person using only
identical replacement parts. This will ensure that the safety of the power tool
is maintained.
Glue Gun Safety Tips
• Do not touch hot glue.
• Do not remove the glue from skin in the event of accidental contact.
Immediately run cold water over and seek medical advice.
• Do not leave glue gun unattended while in use or directly after use.
• Do not touch the nozzle end of the gun while in use or directly after use.
• Do not inhale vapours generated while in use.
• Do not attempt to feed any other materials through the glue gun, eg. crayons,
sealants, candles etc.
POWER TOOL WARNINGS
ELECTRICAL SAFETY
WARNING! When using mains-powered tools, basic safety
precautions, including the following, should always be
followed to reduce risk of re, electric shock, personal injury
and material damage.
Read the whole manual carefully and make sure you know how to switch
the tool off in an emergency, before operating the tool.
Save these instructions and other documents supplied with this tool for
future reference.
The manufacturer cannot accept any liability for damage or accidents which
arise due to a failure to follow these instructions and the safety information.
Before you connect the equipment to the mains supply make sure that the
data on the rating plate are identical to the mains data.
If the supply cord is damaged, it must be replaced by the manufacturer, its
service agent or similarly qualied persons in order to avoid hazard.
Using an Extension Lead
Always use an approved extension lead suitable for the power input of this
tool. Before use, inspect the extension lead for signs of damage, wear and
ageing. Replace the extension lead if damaged or defective.
When using an extension lead on a reel, always unwind the lead completely.
Use of an extension lead not suitable for the power input of the tool or which
is damaged or defective may result in a risk of re and electric shock.
To reduce the risk of electric shock, we recommend the use of a residual
current device (rated 30mA or less).
This appliance is not intended for use by persons (including children) with
reduced physical, sensory or mental capabilities, or lack of experience
and knowledge, unless they have been given supervision or instruction
concerning use of the appliance by a person responsible for their safety.
Young children should be supervised to ensure that they do not play with
the appliance.
GGM-010U
ORIGINAL INSTRUCTIONS
SPECIFICATIONS
Input: 230-240V ~50Hz
Output: 10W
Flow Rate: 6-8g/min
Glue Stick Diameter: 7.2mm
Glue Stick Length: 100mm
Dual Heat Temperatures: 170° - 190°C
Weight (Tool Only): 0.15kg
1 Glues Sticks x 2
2 Protective Nozzle Cover
3 Metal Stand
4 Flow Control Trigger
5 Glue Display
6 Glue Stick Entry
7 Power Cord
ozito-diy.co.uk
1

1
GGM-010U
1. LOADING A GLUE STICK
2. OPERATION
WARRANTY
OZITO UK Unit 9 Stadium Court, Wirral International Business Park,
Plantation Road, Bromborough, Wirral, CH62 3QG
ONLINE MANUAL
Scan this QR Code with your
mobile device to take you to
the online manual.
Installing the Glue Stick
2 Squeeze the ow control
trigger multiple times to allow
the glue stick to be pushed
down.
1 Insert the glue
stick into the glue
stick entry and
slide down gently.
WARNING! ENSURE THE TOOL IS SWITCHED OFF AND
ALLOWED TO COOL DOWN BEFORE PERFORMING ANY
OF THE FOLLOWING TASKS.
3 Press the surfaces
to be glued
together within
15 seconds for a
strong bond.
2 Squeeze the trigger ow
control to release the glue.
4 To stop the ow of glue from
the gun, release the ow
control trigger.
Tip: Ensure the glue sticks are
heated fully to allow an even ow
of glue.
1 Plug the power cord into a
power point and switch on.
WARNING! DO NOT ALLOW HOT GLUE TO COME IN
CONTACT WITH PRODUCT HOUSING DURING USE.
DESCRIPTION OF SYMBOLS
All of our products undergo strict quality checks to ensure that they reach you in
perfect condition. In the unlikely event that your device develops a fault, please
contact our service department at the address shown on this guarantee card.
You can also contact us by telephone using the customer service number shown.
Please note the following terms under which guarantee claims can be made:
1. These warranty terms regulate additional warranty services, which the
manufacturer mentioned below promises to buyers of its new products in addition
to their statutory guarantee claims are not affected by this guarantee. Our
guarantee is free of charge to you.
2. The warranty services only covers defects due to material or manufacturing
faults on a product which you have bought from the manufacturer mentioned
below are limited to either the rectication of said defects on the product or the
replacement of the product, whichever we prefer.
Please note that our devices are not designed for use in commercial, trade or
professional applications. A guarantee contract will not be created if the device
has been used by commercial, trade or industrial business or has been exposed
to similar stresses during the guarantee period.
3. The following are not covered by our guarantee:
- Damage to the device caused by a failure to follow the assembly instructions
or due to incorrect installation, a failure to follow the operating instructions (for
example connecting it to an incorrect mains voltage or current type) or a failure
to follow the maintenance and safety instructions or by exposing the device to
abnormal environmental conditions or by lack of care and maintenance.
- Damage to the device caused by abuse or incorrect use (for example
overloading the device or the use or unapproved tools or accessories), ingress of
foreign bodies into the device (such as sand, stones or dust, transport damage),
the use of force or damage caused by external forces (for example by dropping
it).
- Damage to the device or parts of the device caused by normal or natural wear or
tear or by normal use of the device.
4. Your Product is guaranteed for a period of 36 months from the original
date of purchase and is intended for DIY (Do It Yourself) use only. Lithium Ion
batteries and chargers are covered by a 12 month warranty. Warranty excludes
consumable parts. Guarantee claims should be submitted before the end of the
guarantee period within two weeks of the defect being noticed. No guarantee
claims will be accepted after the end of the guarantee period. The original
guarantee period remains applicable to the device even if repairs are carried out
or parts are replaced. In such cases, the work performed or parts tted will not
result in an extension of the guarantee period, and no new guarantee will become
active for the work performed or parts tted. This also applies if an on-site service
is used.
IN ORDER TO MAKE A CLAIM UNDER THIS WARRANTY YOU MUST RETURN
THE PRODUCT TO THE PLACE OF PURCHASE WITH YOUR REGISTER
RECEIPT.
Please refer to the restrictions of this warranty concerning wearing parts,
consumables and missing parts as set out in the service information in these
operating instructions.
CUSTOMER SERVICE HELPLINE
GB: 0151 294 4488
IRL: 1850 882711
Ozito-diy.co.uk
V Volts Hz Hertz
~Alternating current WWatts
°C Degrees Celsius Read instruction manual
Double insulated

size 445 x 210 mm
Danger! - Read the operating instructions to re-
duce the risk of inquiry
The reprinting or reproduction by any other me-
ans, in whole or in part, of documentation and
papers accompanying products is permitted only
with the express consent of the iSC GmbH.
Subject to technical changes
GGM-010U
GB Additonal operating & safety instructions Glue Gun
Service information
We have competent service partners in all countries named on the guarantee certicate whose contact
details can also be found on the guarantee certicate. These partners will help you with all service re-
quests such as repairs, spare and wearing part orders or the purchase of consumables.
Please note that the following parts of this product are subject to normal or natural wear and that the
following parts are therefore also required for use as consumables.
Category Example
Wear parts*
Consumables* Glue stick
Missing parts
* Not necessarily included in the scope of delivery!
In the eect of defects or faults, please register the problem on the internet at www.isc-gmbh.info. Plea-
se ensure that you provide a precise description of the problem and answer the following questions in all
cases:
• Did the equipment work at all or was it defective from the beginning?
• Did you notice anything (symptom or defect) prior to the failure?
• What malfunction does the equipment have in your opinion (main symptom)?
Describe this malfunction.
Yang/Product-ManagementWeichselgartner/General-Manager
- 135 -
explains the following conformity according to EU directives and norms for
the following product
Glue Gun GGM-010U (Ozito)
2014/29/EU
2005/32/EC_2009/125/EC
X2014/35/EU
2006/28/EC
X2014/30/EU
2014/32/EU
2014/53/EC
2014/68/EU
90/396/EC_2009/142/EC
89/686/EC_96/58/EC
X2011/65/EU
2006/42/EC
Annex IV
Noti ed Body:
Noti ed Body No.:
Reg. No.:
2000/14/EC_2005/88/EC
Annex V
Annex VI
Noise: measured LWA = dB (A); guaranteed LWA = dB (A)
P = KW; L/Ø = cm
Noti ed Body:
2004/26/EC
Emission No.:
Standard references: EN 60335-1; EN 60335-2-45;
EN 55014-1; EN 55014-2; EN 61000-3-2; EN 61000-3-3
Landau/Isar, den 01.06.2016
First CE: 16 Archive-File/Record: NAPR014321
Art.-No.: 44.722.15 I.-No.: 11016 Documents registrar: R. Gehard
Subject to change without notice Wiesenweg 22, D-94405 Landau/Isar
ISC GmbH · Eschenstraße 6 · D-94405 Landau/Isar
Declaration of conrmity

size 445 x 210 mm
Items supplied
Please check that the article is complete as
specied in the scope of delivery. If parts are
missing, please contact our service center or the
sales outlet where you made your purchase at
the latest within 5 working days after purchasing
the product and upon presentation of a valid bill
of purchase. Also, refer to the warranty table in
the service information at the end of the operating
instructions.
• Open the packaging and take out the equip-
ment with care.
• Remove the packaging material and any
packaging and/or transportation braces (if
available).
• Check to see if all items are supplied.
• Inspect the equipment and accessories for
transport damage.
• If possible, please keep the packaging until
the end of the guarantee period.
Danger!
The equipment and packaging material are
not toys. Do not let children play with plastic
bags, foils or small parts. There is a danger of
swallowing or suocating!
Proper use
You can use the hot glue gun to glue the following
materials: Wood, plastics, textiles, cardboard,
ceramics, leather, etc.
The equipment is to be used only for its prescri-
bed purpose. Any other use is deemed to be a
case of misuse. The user / operator and not the
manufacturer will be liable for any damage or inju-
ries of any kind caused as a result of this.
Please note that our equipment has not been de-
signed for use in commercial, trade or industrial
applications. Our warranty will be voided if the
machine is used in commercial, trade or industrial
businesses or for equivalent purposes.
Technical data
Mains connection.....................230-240 V ˜ 50 Hz
Power rating................................................. 10 W
Temperature....................................... 170-190 °C
Glue stick Ø ............................................. 7.2 mm
Totally insulated ............................................. II/&
For EU countries only
Never place any electric power tools in your
household refuse.
To comply with European Directive 2012/19/EC
concerning old electric and electronic equipment
and its implementation in national laws, old elec-
tric power tools have to be separated from other
waste and disposed of in an environment-friendly
fashion, e.g. by taking to a recycling depot.
Recycling alternative to the return request:
As an alternative to returning the equipment to
the manufacturer, the owner of the electrical
equipment must make sure that the equipment
is properly disposed of if he no longer wants to
keep the equipment.The old equipment can be
returned to a suitable collection point that will
dispose of the equipment in accordance with the
national recycling and waste disposal regulations.
This does not apply to any accessories or aids
without electrical components supplied with the
old equipment.