P.L.LIGHT SYSTEMS NXT-LP 600W User manual

NXT-LP 600W/1000W
INSTRUCTION MANUAL

Page 3
Table of Contents
1. Introduction 4
1.1. Used Symbols 4
2. Product Description 4
3. Product Information and Specications 5
3.1. Dimensions 5
3.2. Technical Specications 5
3.3. Environment 5
4. Safety Recommendations and Warnings 6
5. Contents (g1) 7
6. Mounting Kit (g2) 8
7. Controls, Connections and Indications (g3) 8
8. Installing the Fixture 8
8.1. Power and Lamp 8
8.2. Install Eye Bolts 9
8.3. Mount Chain & Front Bracket 9
8.4. Install Chain in Eyebolt(s) 9
8.5. Attach Mounting Bracket 10
8.6. Level Fixture 10
8.7. Connecting the Fixture to the Power Source 10
9. Product Use 10
9.1. Adjusting the Output of the Lamp Manually 11
10. Inspection, Maintenance and Repair 11
10.1. Placement and Replacement of the Lamp 12
10.2. Placement and Replacement of the Reector 13
10.3. Maintenance Cleaning the Reectors 14
11. Storage and Disposal 15
12. Warranty 15
12.1. Limitation of Liability 15

1. Introduction
Thank you for purchasing the P.L. Light Systems NXT-LP. Please read and under-
stand this manually completely before using the product. Only use the product
as specied in this manual.
1.1. Used Symbols
Warning! A warning indicates severe damage to the user and/or product may
occur when a procedure is not carried out as described.
Caution! A caution sign indicates problems may occur if a procedure is not
carried out as described. It may also serve as a reminder to the user.
Note: A note gives additional information, e.g. for a procedure.
This symbol indicates that the reector and lamp can reach very high tempera-
tures (>85 °Celsius).Allow a cool down period before performing maintenance.
With this symbol P.L. Light Systems declares that this product complies with
legal CSA standards.
The symbol on the material, accessories or packaging indicates that this product
may not be discarded as household waste. Dispose of the equipment through a
recycling centre that handles electronics and electrical appliances within Canada
and the United States of America which use separate collection systems for
used electronics and electrical appliances. By disposing of the equipment in the
proper way, you will be helping to prevent possible risks to the environment
and public health, which might otherwise be caused by improper handling of the
discarded equipment. Recycling of materials contributes to the conservation of
natural resources.Therefore, please do not dispose of your old electronics and
electrical appliances via household waste.
2. Product Description
The P.L. Light Systems NXT-LP is an adjustable horticultural light xture. The
P.L. Light Systems NXT-LP can be used to drive a double ended 1000W 400
V electronic (1000W version) or 600W 400V electronic (600W version) high
pressure sodium lamp.
In this manual, the P.L. Light NXT-LP will be referred to as: “the xture”.

Page 5
3.1. Dimensions
3. Product Information and Specications
3.3. Environment
The product is meant for use in climate controlled rooms.The product may be
used in damp environments.The product may not be used in wet environments
or outdoors.The P.L. Light Systems HPS double-ended lamps function optimally
when the ambient temperature is between 20 ~ 30 °Celsius.
3.2. Technical Specications^
^accurate to +/-10% *The use of any lamp, other than specied, will render luminaire warranty null and void.
600W/1000W
length 21.25 in (53.98 cm)
width 11.00 in (27.94 cm)
height 7.50 in (19.05 cm)
weight 10.00 lb (4.54 kg)
1000W
Rated Main Voltage 120V 240V
Input Current 9.08A 4.42A
Power Factor >0.98 >0.98
Input Frequency 50/60Hz 50/60Hz
Actual Input Power 1090W 1060W
Lamp Type*1000W Doubled Ended HPS 1000W 400V electronic ONLY
600W
Rated Main Voltage 120V 240V
Input Current 5.5A 2.65A
Power Factor >0.98 >0.98
Input Frequency 50/60Hz 50/60Hz
Actual Input Power 660W 632W
Lamp Type*600W Double Ended HPS 600W 400V electronic ONLY

4. Safety Recommendations and Warnings
Warning! Carefully read the warnings below before using or working with the
product!
• Always adhere to the local and national building and electrical codes when
installing or using the xture.
• This product may cause interference to radio equipment and should not be
installed near maritime safety communications equipment or other critical navi-
gation or communication equipment operating between 0.45 - 30 MHz.
• Do not use the xture when either its lamp or its power cord are damaged.
Replace the power cord only with original certied cords. Replace the lamp
only with lamps specied by P.L. Light Systems.
• The use of other lamps may damage the product and lamp and will void the
warranty.
• Modications to the cords can lead to unwanted electromagnetic effects,
which makes the product not comply with legal requirements.
• Do not expose the xture to:
-condensing humidity, heavy mist, fog or direct spray;
-(ambient) temperatures outside the specied range;
-dust and contamination;
-direct sunlight during use or HID light that could heat up the ballast.
• Always disconnect the xture from main power source before performing any
maintenance.
• Always allow for a cool down period of at least 30 minutes before touching
the lamp or reector. Touching the lamp or the reector when the lamp is lit or
immediately afterwards will result in severe burns!
• Never touch the lamp with bare hands as this will cause damage to the lamp.
We recommend always wearing cotton gloves when handling the lamp(s).
• Do not use the xture near ammable, explosive or reactive substances. The
lamp and the reector of the xture reach temperatures of >85 °Celsius.
• Do not use sulfur vaporizers or water misters. Sulfur and calcium deposits on
your reector will decrease its efciency.
• The installation and use of the xture is the responsibility of the end user.
Incorrect use or installation can lead to failure and damage to the xture. Dam-
age to the xture and electronic circuitry as a result of incorrect installation
and use revokes the warranty.

Page 7
DRAWN
CHECKED
ENG APPR
MGR APPR
UNLESS OTHERWISESPECIFIED
DIMENSIONSARE IN MILLIMETERS
ANGLES±X.X°
2 PL±X.XX 3 PL ±X.XXX
NAME
Peter Stanley
DATE
08/04/16
Solid Edge
TITLE
NXT_LP-Alpha_Profile_Eye-Hook
SIZE
A1
DWG NO
0001
REV
FILENAME: NXT LP sid eview eye b olt Alpha.dft
SCALE: WEIGHT: SHEET 1 OF 1
REVISIONHIS TORY
REV DESCRIPTION DATE APPROVED
5. Contents (g1)
A. NXT-LP xture
1. Cast aluminum housing with electronic ballast
2. Reector bracket
3. Lamp holders
4. Alpha reector
5. Mounting points (2) Eye Bolts
B. 6ft 120V Power cord with 15A straight blade plug
C. 6ft 240V Power cord with 15A straight blade plug
D. Electronic DE lamp
A5
A1
A2
A4
A1
A5
A4
A2
D
BC
DRAWN
CHECKED
ENG APPR
MGR APPR
UNLESS OTHERWISESPECIFIED
DIMENSIONSARE IN MILLIMETERS
ANGLES±X.X°
2 PL±X.XX 3 PL ±X.XXX
NAME
Peter Stanley
DATE
09/22/16
Solid Edge
TITLE
NXT_LP-1000W_Alpha_NoLamp
SIZE
A1
DWG NO
0001
REV
FILENAME: NXT_LP-1000W_Alpha_NoLamp_Bottom.dft
SCALE: WEIGHT: SHEET 1 OF 1
REVISIONHIS TORY
REV DESCRIPTION DATE APPROVED
600
660 750 825 1000
1150
DRAWN
CHECKED
ENG APPR
MGRA PPR
UNLESSOTHERWISE SP ECIFIED
DIMENSIONSAR E IN MILLIMETERS
ANGLES ±X.X°
2PL ±X.XX 3 PL ±X.XXX
NAME
PeterStanley
DATE
09/21/16
SolidEdge
TITLE
5-15PC13 Connector Cor d
SIZE
A2
DWG NO
0001
REV
FILE NAME: 5-15P C13 Connector Cord.dft
SCALE: WEIGHT: SHEET 1 OF 1
REVISIONHI STORY
REV DESCRIPTION DATE APPROVED
DRAWN
CHECKED
ENG APPR
MGRA PPR
UNLESSOTHERWISE SP ECIFIED
DIMENSIONSAR E IN MILLIMETERS
ANGLES ±X.X°
2PL ±X.XX 3 PL ±X.XXX
NAME
PeterStanley
DATE
09/21/16
SolidEdge
TITLE
6-15PC13 Connec torCord
SIZE
A2
DWG NO
0001
REV
FILE NAME: 6-15P C13 Connector Cord.dft
SCALE: WEIGHT: SHEET 1 OF 1
REVISIONHI STORY
REV DESCRIPTION DATE APPROVED
DRAWN
CHECKED
ENG APPR MGR APPR
UNLESS OTHERWISESPECIFIED
DIMENSIONSARE IN MILLIMETERS
ANGLES±X.X°
2 PL±X.XX 3 PL ±X.XXX
NAME
Mike Ewer
DATE
09/21/16
Solid Edge
TITLE
SIZE
A1
DWG NO REV
FILENAME: NXT LP top Alpha.dft SCALE: WEIGHT: SHEET 1 OF 1
REVISIONHIS TORY
REV DESCRIPTION DATE APPROVED
A3 A3

DRAWN
CHECKED
ENG APPR
MGR APPR
UNLESS OTHERWISE SPECIFIED
DIMENSIONS ARE IN MILLIMETERS
ANGLES ±X.X°
2 PL ±X.XX 3 PL ±X.XXX
NAME
Mike Ewer
DATE
08/05/16
SolidEdge
TITLE
NXT LP Rear View A lpha 2 Eyebolts
SIZE
A2
DWG NOREV
FILE NAME: NXT LP rear view eyebolts Alpha.dft
SCALE: WEIGHT: SHEET 1 OF 1
REVISION HISTORY
REV DESCRIPTION DATE APPROVED
DRAWN
CHECKED
ENG APPR MGR APPR
UNLESS OTHERWISE SPECIFIED
DIMENSIONS ARE IN MILLIMETERS
ANGLES ±X.X°
2 PL ±X.XX 3 PL ±X.XXX
NAME
Peter Stanley
DATE
09/22/16
Solid Edge
TITLE
NXT_LP-1000W_Alpha_NoLamp
SIZE
A1
DWG NO
0001
REV
FILE NAME: NXT_LP-1000W_Alpha_NoLamp_Bottom.dft
SCALE: WEIGHT: SHEET 1 OF 1
REVISION HISTORY
REV DESCRIPTION DATE APPROVED
600
660 750 825 1000
1150
7. Controls, Connections and Indications (g3)
A. Dimming control knob (adjustable see 9.1)
B. Integrated level
C. 120V/240V Cord receptacle
6. Mounting Kit (g2)
A. (2) S-hooks
B. (1) Wire bracket
C. (2) Eye bolts
8. Installing the Fixture
Warning! Avoid coiled cords. Coiled cords may lead to electromagnetic
interference.
Warning! Always install the lamp before connecting the xture to the main
power source
Warning! Ensure the local cabling can support the voltage and current re-
quirements of the xture.
C
A
B
B
A
A
• Switch off mains power source
• Install the lamp in the xture (see paragraph 10.1).
8.1. Power and Lamp
Warning! Always allow ample space above the installed xture to ensure good
airow. This will prevent an excessive build-up of heat between the xture and
the ceiling which could result in damage to the electronics components and/or
lamp.
C

Page 9
8.2. Install Eye Bolts
• Thread eye bolts in designated areas (2) and tighten.
• Cut chain to appropriate length for desired mounting height
• Hang one chain over truss/track and insert mounting bracket through nal
links on both ends of chain (3)
• Rotate bracket so that hooks are facing downward (4)
8.3. Mount Chain & Front Bracket
8.4. Install Chain in Eyebolt(s)
• Cut second chain to appropriate length for desired mounting height: hang
chain over truss/track
• Insert S-hook(s) through last link on either end of chain (5)
• Raise xture to ceiling and insert free ends of S-hook(s) in eyebolts(s) on
xture housing. (6)
(3) (4)
(5) (6)
Note: Dual eyebolts are recommended for leveling purposes.
DRAWN
CHECKED
ENG APPR
MGR APPR
UNLESS OTHERWISESPECIFIED
DIMENSIONSARE IN MILLIMETERS
ANGLES±X.X°
2 PL±X.XX 3 PL ±X.XXX
NAME
Mike Ewer
DATE
09/21/16
Solid Edge
TITLE
SIZE
A1
DWG NO REV
FILENAME: NXT LP top Alpha.dft
SCALE: WEIGHT: SHEET 1 OF 1
REVISIONHIS TORY
REV DESCRIPTION DATE APPROVED
(2)
designated eye bolt holes

8.7. Connecting the Fixture to the Power Source
Warning! Ensure the cord is not coiled and does not touch any hot surfaces.
• Plug the power cord into the outlet.
9. Product Use
Warning! Never use the xture without a lamp or reector!
Caution! Before you dim or boost your HPS lamp, make sure that you run it at
nominal value (100%) for at least 100 hours to stabilize the lamp. Failing to do
so may lead to sub-optimal light levels and premature end of life failure of your
lamp.
• Lower front of reector collar onto mounting bracket hooks
• Adjust so that bracket is securely inserted beneath collar
8.5. Attach Mounting Bracket
8.6. Level Fixture
• Use integrated level on the back of the housing to adjust the light xture.
Fixture is level when spirit level bubble is centered.
DRAWN
CHECKED
ENG APPR
MGR APPR
UNLESS OTHERWISE SPECIFIED
DIMENSIONS ARE IN MILLIMETERS
ANGLES ±X.X°
2 PL ±X.XX 3 PL ±X.XXX
NAME
Mike Ewer
DATE
08/05/16
SolidEdge
TITLE
NXT LP Rear View Alpha 2 Eyebolts
SIZE
A2 DWG NOREV
FILE NAME: NXT LP rear view eyebolts Alpha.dft
SCALE: WEIGHT: SHEET 1 OF 1
REVISION HISTORY
REV DESCRIPTION DATE APPROVED
level
DRAWN
CHECKED
ENG APPR
MGR APPR
UNLESS OTHERWISE SPECIFIED
DIMENSIONS ARE IN MILLIMETERS
ANGLES ±X.X°
2 PL ±X.XX 3 PL ±X.XXX
NAME
Mike Ewer
DATE
08/05/16
SolidEdge
TITLE
NXT LP Rear View A lpha 2 Eyebolts
SIZE
A2
DWG NOREV
FILE NAME: NX T LP rear view eyebolts Alpha.dft
SCALE: WEIGHT : SHEET 1 OF 1
REVISION HISTORY
REV DESCRIPTION DATE APPROVED
DRAWN
CHECKED
ENG APPR
MGR APPR
UNLESS OTHERWISE SPECIFIED
DIMENSIONS ARE IN MILLIMETERS
ANGLES ±X.X°
2 PL ±X.XX 3 PL ±X.XXX
NAME
Mike Ewer
DATE
09/21/16 SolidEdge
TITLE
NXT_LP-Front_Alpha_ChainMount
SIZE
A2
DWG NOREV
FILE NAME: NX TLP front view hanging hook Alpha.d ft
SCALE: WEIGHT : SHEET 1 OF 1
REVISION HISTORY
REV DESCRIPTION DATE APPROVED

Page 11
Note: Adjustment occurs gradually (60 seconds per step) to increase the
lifespan of the lamp.
• Turn the output control knob to adjust the output of the lamp:
- 600W DE: 300/400/500/600/660 Watt
- 1000W DE: 600/660/750/825/1000/1150 Watt
9.1. Adjusting the Output of the Lamp Manually
10. Inspection, Maintenance and Repair
Warning! Disconnect the product from main power source before performing
any maintenance or repairs.
Warning! Do not open or disassemble the xture, it contains no serviceable
parts inside. Opening the xture can be dangerous and will void the warranty.
Warning! Always allow for a cool down period of at least 20 minutes before
touching the lamp or reector.
Caution! Do not clean the xture with detergents, abrasives or other aggres-
sive substances.
Caution! Wait 20 minutes before activating the xture after maintenance
work has been conducted.
• Regularly check the xture for dust or dirt build up. Clean if necessary.
Contamination may cause overheating and decreased performance.
-- Clean the reector as directed in 10.3.
-- Clean the outside of the xture using a dry or damp cloth as necessary.
• Check the lamp monthly for discolorations or black markings.Always replace
a damaged lamp.
Note: Before initial use, the lamp could have black markings.This will disappear
when the lamp runs on full power. If not, replace the lamp.
• Regularly check the power cord of the product to ensure it is undamaged.

DRAWN
CHECKED
ENG APPR
MGR APPR
UNLESS OTHERWISESPECIFIED
DIMENSIONSARE IN MILLIMETERS
ANGLES±X.X°
2 PL±X.XX 3 PL ±X.XXX
NAME
PeterSt anley
DATE
09/22/16
Solid Edge
TITLE
NXT_LP-1000W_Alpha_WithLam p
SIZE
A1
DWGNO 0001 REV
FILENAME: NXT_LP-1000W_Alpha_WithLamp_Bottom.dft
SCALE: WEIGHT: SHEET1 OF 1
REVISIONHISTORY
REV DESCRIPTION DATE APPROVED
600
660 750 825 1000
1150
DRAWN
CHECKED
ENG APPR
MGR APPR
UNLESS OTHERWISESPECIFIED
DIMENSIONSARE IN MILLIMETERS
ANGLES±X.X°
2 PL±X.XX 3 PL ±X.XXX
NAME
Peter Stanley
DATE
09/22/16
Solid Edge
TITLE
NXT_LP-1000W_Alpha_WithLamp
SIZE
A1
DWG NO
0001
REV
FILENAME: NXT_LP-1000W_Alpha_WithLamp_Bottom.dft
SCALE: WEIGHT: SHEET 1 OF 1
REVISIONHIS TORY
REV DESCRIPTION DATE APPROVED
600
660 750 825 1000
1150
DRAWN
CHECKED
ENG APPR
MGR APPR
UNLESS OTHERWISESPECIFIED
DIMENSIONSARE IN MILLIMETERS
ANGLES±X.X°
2 PL±X.XX 3 PL ±X.XXX
NAME
Peter Stanley
DATE
09/22/16
Solid Edge
TITLE
NXT_LP-1000W_Alpha_WithLamp
SIZE
A1
DWG NO
0001
REV
FILENAME: NXT_LP-1000W_Alpha_WithLamp_Bottom.dft
SCALE: WEIGHT: SHEET 1 OF 1
REVISIONHIS TORY
REV DESCRIPTION DATE APPROVED
600
660 750 825 1000
1150
10.1. Placement and Replacement of the Lamp
• Switch off main power source.
• Hold the lamp with a fabric glove to prevent it from falling. Use a protective
glove if the lamp is damaged.
• Open the lamp holders by sliding the plastic locks outwards (7).
• Carefully take the old lamp out of the xture (8).
• Install the new lamp with the getter (A) near the ballast (9)
• Use a fabric glove to carefully press the lamp in the tting until the metal
springs hold the lamp.
• Using index nger, apply pressure on the bottom of the rear, center portion of
lamp holder(10)—moving the sliding mechanism towards the lamp until front
edge aligns with lamp lock indicators (B) on reector bracket. Repeat on other
side. Ensure sliding mechanisms have fully closed against the stops, as loose
connections may cause arcing—potentially creating a fire risk and/or voiding
warranties.
• Switch on main power source.
g(7)
Note: The lamp must be replaced approximately every 10,000 burning hours.
Caution! Always wear cotton gloves when touching a lamp to avoid creating a
dark spot on the bulb from the oils on your skin.
Caution! Only use lamps specied by P.L. Light Systems (see paragraph 3.2).
600W/1000W DE
f
f
g(8)
m
g(10)
f
f
g(9)
getter
DRAWN
CHECKED
ENG APPR
MGR APPR
UNLESS OTHERWISESPECIFIED
DIMENSIONSARE IN MILLIMETERS
ANGLES±X.X°
2 PL±X.XX 3 PL ±X.XXX
NAME
Peter Stanley
DATE
08/04/16
Solid Edge
TITLE
NXT_LP-Alpha_Profile_Eye-Hook
SIZE
A1
DWG NO
0001
REV
FILENAME: NXT LP sid eview eye bo lt Alpha.dft
SCALE: WEIGHT: SHEET1 OF 1
REVISIONHIS TORY
REV DESCRIPTION DATE APPROVED
(A)
m
lamp lock indicator
(B)

Page 13
DRAWN
CHECKED
ENG APPR
MGR APPR
UNLESS OTHERWISESPECIFIED
DIMENSIONSARE IN MILLIMETERS
ANGLES±X.X°
2 PL±X.XX 3 PL ±X.XXX
NAME
Peter Stanley
DATE
09/22/16
Solid Edge
TITLE
NXT_LP-1000W_Alpha_NoLamp
SIZE
A1
DWG NO
0001
REV
FILENAME: NXT_LP-1000W_Alpha_NoLamp_Bottom.dft
SCALE: WEIGHT: SHEET 1 OF 1
REVISIONHIS TORY
REV DESCRIPTION DATE APPROVED
600
660 750 825 1000
1150
DRAWN
CHECKED
ENG APPR
MGR APPR
UNLESS OTHERWISESPECIFIED
DIMENSIONSARE IN MILLIMETERS
ANGLES±X.X°
2 PL±X.XX 3 PL ±X.XXX
NAME
Mike Ewer
DATE
09/21/16
Solid Edge
TITLE
SIZE
A1
DWG NO REV
FILENAME: NXT LP top Alpha.dft
SCALE: WEIGHT: SHEET 1 OF 1
REVISIONHIS TORY
REV DESCRIPTION DATE APPROVED
10.2. Placement and Replacement of the Reector
Note: P.L. Light Systems recommends cleaning the reector once a year (see
10.3) to maintain optimum performance. Depending on the environment and
contamination levels the reector will degrade over time and will eventually
need to be replaced.
• Switch off main power source.
• The lamp doesn’t need to be removed to remove/replace the reector.
• Support the reector with hands on both sides (11).
• Lightly compress the sides of the reector inwards, past the bracket tabs. (12).
• Lift gently (13).
• Remove the reector.
• Position the new/clean reector above the bracket.
• Lightly compress the sides of the reector inwards, past the bracket tabs.
• Release the reector
• Using both hands, adjust the reector from the inside, by gently pressing out-
wards until the outer rim ts securely beneath the collar tabs on all sides. (14)
• Switch on main power source.
Note: Wear cotton gloves or wash hands thoroughly with soap & water to
remove any grime/oils before handling reector.
g(11)
f
f
f
f
g(12)
g(13)
m
m
m
m
g(14)
f f
DRAWN
CHECKED
ENG APPR
MGR APPR
UNLESS OTHERWISESPECIFIED
DIMENSIONSARE IN MILLIMETERS
ANGLES±X.X°
2 PL±X.XX 3 PL ±X.XXX
NAME
Peter Stanley
DATE
08/04/16
Solid Edge
TITLE
NXT_LP-Alpha_Profile_Eye-Hook
SIZE
A1
DWG NO
0001
REV
FILENAME: NXT LP sid eview eye b olt Alpha.dft
SCALE: WEIGHT: SHEET 1 OF 1
REVISIONHIS TORY
REV DESCRIPTION DATE APPROVED
DRAWN
CHECKED
ENG APPR
MGR APPR
UNLESS OTHERWISESPECIFIED
DIMENSIONSARE IN MILLIMETERS
ANGLES±X.X°
2 PL±X.XX 3 PL ±X.XXX
NAME
Mike Ewer
DATE
09/21/16
Solid Edge
TITLE
SIZE
A1
DWG NO REV
FILENAME: NXT LP top Alpha.dft
SCALE: WEIGHT: SHEET 1 OF 1
REVISIONHIS TORY
REV DESCRIPTION DATE APPROVED

10.3. Maintenance Cleaning the Reectors
Regular cleaning of reectors is essential for optimal lighting performance. Your
reectors need to be cleaned at a minimum every two years, but every year is
highly recommended.
• Switch off main power source.
• Remove the reector from xture(see paragraph 10.2.).
• A reector can be cleaned with a 1:100 vinegar to water solution. Dip the
reector in this solution for a few seconds.
• If necessary, rub lightly with a ne ngernail brush to loosen the dirt. Once
the dirt is loosened, rinse the reector in distilled water. Rinse the reector
once more in distilled water.
• Hang to air dry. Once dry, if there are still heavy deposits or anything that
cannot be removed, it is time for the reector to be replaced.
• Re-install reector (see paragraph 10.2.)
• Switch on main power source.
Note: P.L. Light Systems recommends for your safety, when cleaning
reectors always maintain the correct ratio and never add other chemicals to
the solution.Wearing hand and eye protection is advised.

Page 15
11. Storage and Disposal
Caution! The lamp contains mercury.
12.Warranty
P.L. Light Systems warrants the mechanical and electronic components of their
product to be free of defects in material and workmanship if used under nor-
mal operating conditions for a period of two (2) years from the original date
of purchase. If the product shows any defects within this period and that defect
is not due to user error or improper use P.L.Light Systems shall, at its discre-
tion, either replace or repair the product using suitable new or reconditioned
products or parts. For the reector and supplied HPS lamp the warranty period
is one (1) year from the original date of purchase. Note:The use of any lamp
other than specied by P.L. Light Systems (including Metal Halide), will render
luminaire warranty null and void. In case P.L. Light Systems decides to replace
the entire product and/or warrantied components, this limited warranty shall
apply to the replacement product/components for the remaining initial warran-
ty period, i.e. two (2) years from the date of purchase of the original product.
For service, return the xture to the place of purchase with the original sales
receipt.All information represented in this guide has been checked to be as ac-
curate as possible. However errors may be present. P.L. Light reserves the right
to refuse service to any product at their discretion.
2 YEAR
WARRANTY
• Store the xture in a dry and clean environment, with an ambient tempera-
ture of -20 ~ 85 °Celsius.
• The product must not be discarded as unsorted municipal waste, but must be
collected separately for the purpose of treatment, recovery and environmental-
ly sound disposal.
Caution! The lamps are chemical hazardous waste. Manage in accordance with
local disposal laws.
In no event shall P.L. Light be liable for any incidental, special or consequen-
tial damages, including but not limited to loss of business, prots, data or use,
whether in an action in contract or based on a warranty, arising out of or in
connection with the use or performance of the product, even if P.L. Light has
been advised of the possibility of such damages.
12.1. Limitation of Liability

1.800.263.0213 | www.nxt-lp.com
4800 Hinan Dr., Beamsville, ON, Canada
P.L. LIGHT SYSTEMS
pl_light
/pllightsystems
@pllight
/c/pllight
/p-l--light-systems