Pace Systems 250-050 User manual

Touch Glass Alerter (Without Chime)
Models Covered: 250-010 & 250-050
· Touch Glass Alerter (TGA)
· 2 x AA Battery
· 3 x Double Sided Sticky Pads
· 1 x Cleaning Sachet
Pack Contents
Product Overview
The TGA is a wireless doorbell alerter that uses radio frequency (RF) technology to activate a separate door
chime unit (not supplied with this package), with the TGA acting as the transmitter and the door chime unit as the
receiver. There are over 250 RF channels that the TGA and door chime unit can operate on and the units come
supplied with a standard default factory channel setting. Channel settings can easily be changed and further
details on this process can be found in the Channel Set up and Additional TGA Units section.
The TGA has been designed to be attached to the inside of the designated glass door or window and activated
from the outside of that position, simply by swiping the hand across the ‘Touch Here for Assistance’panel. Once
the panel has been swiped then the TGA transmits the signal to the door chime receiver and the chime will
activate.
Please read and follow the instructions below before attempting to activate or install your additional TGA with
your existing door chime. It is recommended that you retain a copy of these instructions for future use.
Initial Set up Instructions
1. Check the contents of the pack and ensure all components listed are present. Contact your suppliers if
anything is missing.
2. This TGA is designed to be installed along side one or more existing TGA units to cover more than one
entrance. Therefore before fitting the additional TGA please follow the instructions as detailed in the
Adding additional TGA to chime section.
3. With a successful pairing of the additional device, you may proceed with the fitting of the new TGA as
described below. Should the units not pair, please follow the instructions shown in the To reset section.
If this process fails to pair the devices, please refer to the Trouble Shooting Guide and User Hints
section.
Please note the TGA has a built in anti-annoyance feature that restricts the activation of the device, please read
the Operation section for more details.

Channel Set up
The unit comes from the factory on a pre-set channel. However should your door chime activate intermittently or
for no apparent reason, it is possible that another unit is operating nearby on the same channel.
To change the channel : The door chime has a self learning channel feature so no adjustments are required.
1. Remove the batteries from the chime unit and leave to rest for 60 seconds (1 minute)
2. Remove and re-insert the batteries in the TGA
3. Re-insert the batteries into the chime unit. A double beep will be heard
4. Within 30 seconds of the double beep press the TGA to confirm the new code is working
Should you need to change channels, this process can be followed many times as there are over 250 different
channels.
1. Press the ‘CODE’button, located on the back of the Standard chime, for 1 to 2 seconds until a beep is
heard followed by step 3 below
2. Or if issued with the Illuminated chime, slide off the battery cover and press the ‘CODE’button, for 1 to 2
seconds until a beep is heard followed by step 3 below
3. Press the new TGA within 5 seconds and the chime will sound.
A maximum of 4 TGA’s can be paired to the same chime
If a series of beeps are heard this indicates memory is full.
To reset:
1. Remove the batteries from the chime unit for 30 seconds
2. Remove and re-insert the batteries in the TGA
3. Re-insert the batteries into the chime unit. A double beep will be heard
Adding additional TGA to chime
Additional TGA Units
Additional TGA Units can be purchased and installed at other locations i.e.. other entrances etc. They can be
adjusted to a different tone so that the source of the chime can be identified. Additional units can be obtained
from your retailer or from Pace Systems Ltd Telephone: [phone]
Code
Button
Mode Code Volume
R14 or Size C
R14 or Size C
Mute
Switch
On
Off
+
+
Code
Button
Standard Door Chime Illuminated Door Chime

Positioning and Fixing the TGA
The position of the TGA on the glass window/door must be carefully chosen (Please see places to be avoided)
It is recommended that before permanently attaching the TGA to the glass, first test the operation of the unit in the
chosen location, ensuring the TGA can be activated through the glass and the chime unit sounds.
To fix the TGA:
1. Remove the protective film from the front of the TGA.
2. Insert batteries into TGA (see fitting instructions overleaf)
3. Position the double sided adhesive pads supplied on the front face of the
TGA as illustrated in the diagram below. (Remember the pads need to be
stuck to the front of the TGA so the unit can be placed on the inside of the
glass window/door)
4. Find a suitable position on the window or door to enable operation from a
wheelchair user if applicable, whilst paying attention to the places to avoid
as detailed below
5. Remove the backing from the double sided pads
6. Stick the unit inside the window/door a minimum of 900mm above street
level, making sure it is accessible to its intended users.
Pad Position
Tone
Selector
Pad Position
3 x pads Provided
Rear View of TGA
Places to be avoided
1. A height below 900mm from street level
2. Close to metal shop fittings and metal window or door frames (keep at least
200mm away)
3. Close to where people may congregate or walk close too and set off the
TGA in error
4. Direct sunlight
5. Locations likely to encounter heavy rain.
Touch the TGA once; The door chime unit will sound (and flash if illuminated
version) then stop as soon as the melody ends. For the chime to sound again, the
TGA must be touched again, however the anti annoyance feature will prevent the
chime from sounding again for a period of 30 to 40 seconds. The red LED on the
front of the TGA will operate briefly to show the user that the unit has operated
correctly.
Operation
To fit or replace batteries: Slide open the battery cover, insert the batteries into the
battery compartment ensuring the battery polarities match the internal markings.
Refit the battery cover.
Requires 2x1.5v AA batteries (supplied)
Touch Glass Alerter (TGA)
+ +

Trouble Shooting Guide and user Hints
Problem Possible Causes Suggested Remedy
Chime unit does not sound
when touching TGA Unit is out of range Move the Door Chime closer to the TGA
TGA and Chime unit are not
on the same channel Follow channel set up instructions
Batteries need replacing If the LED on the TGA does
not illuminate then replace the
batteries in the TGA
If the LED on the TGA
illuminates but the LED does
not illuminate on the Chime
unit replace the batteries in the
chime unit
Door Chime sounds without
TGA being pressed A similar wireless product is being used on the same
channel
Change the Channel by
follow channel set up
An additional TGA will not
work with existing chime Units not paired Follow steps 1 and 2 in adding an additional TGA
Anti-annoyance feature Wait 30 to 40 seconds before
activating TGA
Important
The TGA is a sensitive electronic product and the following precautions should be followed:-
· The door chime should only be used in dry conditions
· Do not expose the door chime unit to direct sunlight
· If leaving the TGA or door chime for long periods remove batteries and store safely
· Do not drop either unit or subject to excessive blows
· The operating range is up to 80M, however the range of the wireless signal will be reduced if transmitted
through a number of walls or ceilings as well as by metal door or window frames.
Pace Systems Limited
Tel. [phone]
www.pace-systems.co.uk
Warranty
This unit is guaranteed against faulty parts or workmanship for a period of one year from date of purchase. This
Warranty does not cover batteries, damage caused by battery leakage, damage caused by incorrect installation,
or physical damage to the casing.
This guarantee does not affect your statutory rights
Warning
· Do Not mix old and new batteries
· Do not mix different types of batteries
· Batteries must be inserted with the correct polarity
· Exhausted batteries must be removed immediately