Pacer PT200S User manual

Notes:
M2962 4-28-04 vah
Warranty
This product is fully warranted against defective
materials and/or workmanship for a period of one
year after purchase, provided it was not improperly
used. For your protection, please use this product as
soon as possible. If returned, it must be securely
wrapped, sent prepaid and insured to:
Pacer Industries, Inc.
1450 First Avenue
Chippewa Falls, WI 54729
PH: 715-723-1141
FX: 715-723-7890
Please include a note with name, address, telephone
number and description of the problem. Although
we provide assistance on Pacer products both
personally and through our literature, it is still the
total responsibility of the customer to determine the
suitability of the product for use in their application.
This manual is provided by Pacer Industries without
any kind of warranty. Precautions have been taken
in accurately preparing this manual; however, we
neither assume responsibility for any omissions or
errors that may appear nor assume liability for any
damages that result from the use of the products in
accordance with the information contained in the
manual.

INTRODUCTION
Pacer models PT200S (ºF) and PT300 (ºC) digital thermometers
are accurate, versatile instruments for measuring temperature.
They are available with a round immersion tip (standard) or a
sharp insertion tip (no-charge option).
The PT200S has a high and low range and the PT300 has a display
hold switch setting.
SECTION 1 - SPECIFICATIONS
Sensor: Semiconductor (PTC)
Range:
Temperature – PT200S:
Low range: -55.0º to 199.9ºF
High range: -55º to 300ºF
Temperature – PT300: -55.0º to 150.0ºC
Accuracy:
PT200S: ±1ºF ±1 digit
PT300: ±0.5ºC ±1 digit
Resolution:
PT200S:
Low range: 0.1ºF
High range: 1ºF
PT300: 0.1ºC
Response time: Approximately15 seconds
Sampling rate: 2.5 measurements/second
Operating temperature: 32º to 120ºF (0º to 49ºC)
Storage temperature:: 14º to 140ºF (-10º to 60ºC)
Power supply: 9V alkaline battery (Eveready 522
or equivalent)
Battery Life: Approximately 200 hours
Battery check: Automatic “LO BAT” display
Dimensions:
Instrument: 4.75” x 2.75” x 1”
Weight: 6 ounces with battery
Display: 0.5” LCD, 3 ½ digits
-1-
SPECIFICATIONS - continued
Options:
CG-3 charger: PN 6043 (with NiMH battery)
Insertion (sharp) tip: No charge, specify at purchase
Rigid carrying case: PN 6005
Leatherette holster: PN 3865
Included:
1 piece: PT200S or PT300 thermometer
1 piece: 9V alkaline battery
1 piece: PN M2962 operation manual
SECTION 2 – OPERATION
PT200S The switch to the left is OFF; center position is ON
in the LOW RANGE and to the right is ON in the
HIGH RANGE. Hold the probe tip at the location to
be measured. The K-type thermocouple is located at
the tip. If the temperature being measured is over
range (see SPECIFICATIONS), a “1” will be
displayed with the other digits blinking.
PT300 The switch to the left is OFF, center position is ON
and to the right is the display “HOLD” position.
Hold the probe tip at the location to be measured.
The K-type thermocouple is located at the tip. If the
temperature being measured is over range (see
SPECIFICATIONS), a “1” will be displayed with
the other digits blinking.
NOTE: On both units “LO BATT” indicates a low
battery. Change (or charge) the battery.
-2-