PacLights FFHS Series Assembly instructions
CAUTION: PLEASE FOLLOW THIS INSTRUCTION MANUAL CAREFULLY TO
PREVENT ANY INJURIES OR COMPLICATIONS THAT MAY ARISE.
Before installing or maintaining the luminary, make sure all powers are
WARNING:
.TURNED OFF
Verify that supply voltage is correct by comparing it with the label information on all
fixtures.
Make all connections in accordance with the NEC requirements, and make sure all
luminaries are properly secured to prevent any wire complications. This luminary is
to always be installed with the lens facing down and its not to exceed the maximum
ambient temperature rating noted on the specification sheet.
FFHS400, FFHS500, FFHS600, FFHS750, FFHS1000,Includes:
FFHS1200
Copyright © 2019 PacLights All Rights Reserved
STANDARD INSTALLATION STEPS
FFHS J-Box
TO FIXTURE
ACN [ /WHITE]
ACL [ /BLACK]
ROUND [ ]
NEUTRAL [WHITE]
ROUND [ ]
[BLACK]
INPUT
OUTPUT
DIM
Using a J-Box, Connect the ACL and the ACN from the J-Box to the Fixture with the AC Power Supply
cords. Follow the Wiring Diagram provided.
02-00036-191021
Note: Instructions are subject to change at any time without notice
FFHS Series LED Flood Light Installation Sheet
Each FFHS Luminaire includes a Trunnion Mount. The Trunnion Mount can be
adjusted to a desired tilt angle for all the FFHS Series. The FFHS600/750/1000/1200
have a lever on each side along with larger side brackets to support the heavy fixture.
FFHS400/500 FFHS600/750/1000/1200
FFHS 400/500 and FFHS600/750/1000/1200 Luminaires have Trunnion Mount
bolt hole dimensions as seen below. Please use the Trunnion Mount dimensions
below to determine the drilling template to follow if the fixture is going to be surface
mounted with the Trunnion Mount.
The FFHS Luminaires can be adjusted by using a wrench to loosen the center
bolts and the arc slot bolts located on the sides of the FFHS Luminaire. The
FFHS 600/750/1000/1200 Luminaires will also need the lever bolts located on the
sides of the FFHS Luminaire to be loosened. The fixture will now be able to rotate
to the desired tilt/angle. Replace the arc slot bolts and tighten all the other bolts.
0.62” Ø0.62” Ø0.64
FFHS400/500
FFHS600/750/1000/1200
6.50”
8.00”
0.64” 7.75”
9.50”
GRAY (-)
Violet (+)
GRAY (-)
Violet (+)
Surge Protector
Main Wire
Connector
DIM
AC Power Supply
Optional Dim Connector
ACL [BLACK]
ACN [WHITE]
ROUND [ ]
Center Bolt
Arc Slot Bolt
Lever Bolt
Center Bolt
Arc Slot Bolt
Lever Bolt
Lever
Page 1 of 2
Surge Protector
CAUTION: PLEASE INCLUDE THE JUNCTION BOX PROVIDED.
Junction Box contains a necessary Surge Protector.
WARNING:
ACL [BLACK]
ACN [WHITE]
ROUND [ ]
Each FFHS Series fixture is provided with a Junction Box that contains wire
Connectors and a Surge Protector. The Surge Protector is required! The Surge
Protector is pre-installed, fastened with a screw inside the Junction Box. Please follow
the wiring diagram below.
Screw
Hole
Surge Protector
Connector
2
1
3
2
3
Copyright © 2019 PacLights All Rights Reserved Note: Instructions are subject to change at any time without notice
The Optional Slip Fitter mount AC-FHS-SF provides a tilt option for the FFHS
luminaire. There are several sizes for the FFHS Series. The AC-FHS-SF1 is for the
FFHS400/500 luminaire. The AC-FHS-SF2 is for the FFHS 600/750. The
AC-FHS-SF3 is for the FFHS 1000/1200 luminaire. Align the Slip Fitter to the FFHS
Handle and fasten the two pieces together
using the [4] Hex Head Bolts and nuts.
FFHS Series LED Flood Light Installation Sheet
Once the Slip Fitter is properly
secured onto the FFHS Fixture, one
can then run the Power Cable from
the Fixture to the inside of the pole
to allow it to be powered with an
AC Power Supply Cable. Follow the
wiring diagram. One can then place
the Slip Fitter on top of a standard
2 3/8” diameter pole, adjust the
orientation and fasten the [4] Hex
Head Bolts to secure the Slip Fitter
to the pole.
02-00036-191021
After properly securing the FFHS Luminaire
with the Slip Fitter to the pole, if needed, adjust
directly at the Slip Fitter by removing the Phillips
head screws, the cover, loosening the bolt with
a wrench, and pulling slightly to move the parts
freely from the teeth. After adjusting the Slip
Fitter tilt, mate the parts at the teeth and fasten
the bolt, put the cover in place, install the screws.
Ø2 3/8”
The Optional Glare Shield AC-FHS-HD provides a restriction for excess glare by
the FFHS luminaire. There are several glare shields for the FFHS Series. The
AC-FHS-HD1 is for the FFHS400/500, the AC-FHS-HD2 is for the FFHS600/750, and
the AC-FHS-HD3 is for the FFHS1000/1200 luminaires. The Glare Shield restricts the
amount of light pollution and light trespass.
Align the Glare Shield to the front of
the FFHS fixture holes along the rim.
Fasten the Glare Shield to the fixture
with the [5] Socket Head Cap screws.
Bolts
Bolts
Bolts
Teeth
Screws
Bolt
Screws
Glare Shield
Glare Shield
Glare Shield
Slip Fitter
FFHS Handle
Pole
Cover
Optional Glare Shield
Optional Slip Fitter
The FFHS Luminaire Series have an Optional Photo Cell that can be attached to the
Junction Box at the side. The Photo Cell has three wires: Neutral [White], Hot [Black],
and Hot [Red]. The Neutral [White] attaches inline with the Power Supply and Fixture
ACN Neutral [Blue/White] wires. The Photo Cell has an internal ‘switch’ with a Hot
[Black] wire that attaches to the Power Supply Hot [Black] and a Hot [Red] wire that
attaches to the Fixture ACL [Brown/Black] wire. Mounting is recommended in the
upright position. Please follow the wiring diagram as shown.
Optional Photo Cell
[RED]
NEUTRAL [WHITE]
[BLACK]
Slip Fitter
Glare Shield
[BLACK]
NEUTRAL [WHITE]
[RED]
PHOTO CELL
Page 2 of 2
AC Power Supply FFHS FIXTURE
ACN [ /WHITE]
ACL [ /BLACK]
ROUND [ ]
FFHS Handle
JUNCTION BOX
1
2
3
1
2
11
2
2
3
This manual suits for next models
6
Other PacLights Floodlight manuals
