PacLights FFHS/2 Series Assembly instructions
CAUTION: PLEASE FOLLOW THIS INSTRUCTION MANUAL CAREFULLY TO
PREVENT ANY INJURIES OR COMPLICATIONS THAT MAY ARISE.
Before installing or maintaining the luminary, make sure all powers are
WARNING:
.TURNED OFF
Verify that supply voltage is correct by comparing it with the label information on all
fixtures.
Make all connections in accordance with the NEC requirements, and make sure all
luminaries are properly secured to prevent any wire complications. This luminary is
to always be installed with the lens facing down and its not to exceed the maximum
ambient temperature rating noted on the specification sheet.
FFHS/2-400, FFHS/2-500, FFHS/2-600, FFHS/2-750,Includes:
FFHS/2-1000, FFHS/2-1200
Copyright © 2021 PacLights All Rights Reserved
STANDARD INSTALLATION STEPS
FFHS/2 J-Box
TO FIXTURE
ACN [ /WHITE]BLUE
ACL [ /BLACK]BROWN
G GREENROUND [ ]
NEUTRAL [WHITE]
G GREENROUND [ ]
HOT [BLACK]
INPUT
OUTPUT
DIM
Using a J-Box, Connect the ACL and the ACN from the J-Box to the Fixture with the AC Power Supply
cords. Follow the Wiring Diagram provided.
02-00036-211214
Note: Instructions are subject to change at any time without notice
FF FHS/2 Series LED lood Light Installation Sheet
Each FFHS/2 Luminaire includes a Trunnion Mount. The Trunnion Mount can be
adjusted to a desired tilt angle for all the FFHS/2 Series. The FFHS/2-600/750/1000
/1200 have a lever on each side along with larger side brackets to support the heavy
fixture.
FFHS/2-400/500 FFHS/2-600/750/1000/1200
FFHS/2-400/500 and FFHS/2-600/750/1000/1200 Luminaires have Trunnion
Mount bolt hole dimensions as seen below. Please use the Trunnion Mount
dimensions below to determine the drilling template to follow if the fixture is going
to be surface mounted with the Trunnion Mount.
The FFHS/2 Luminaires can be adjusted by using a wrench to loosen the center
bolts and the arc slot bolts located on the sides of the FFHS/2 Luminaire. The
FFHS/2-600/750/1000/1200 Luminaires will also need the lever bolts located on the
sides of the FFHS/2 Luminaire to be loosened. The fixture will now be able to rotate
to the desired tilt/angle. Replace the arc slot bolts and tighten all the other bolts.
0.62” Ø0.62” Ø0.64
FFHS/2-400/500
FFHS/2-600/750/1000/1200
6.50”
8.00”
0.64” 7.75”
9.50”
GRAY (-)
Violet (+)
GRAY (-)
Violet (+)
Surge Protector
Main Wire
Connector
DIM
AC Power Supply
Optional Dim Connector
ACL [BLACK]
ACN [WHITE]
G GREENROUND [ ]
Center Bolt
Arc Slot Bolt
Lever Bolt
Center Bolt
Arc Slot Bolt
Lever Bolt
Lever
Page 1 of 2
Surge Protector
CAUTION: PLEASE INCLUDE THE JUNCTION BOX PROVIDED.
Junction Box contains a necessary Surge Protector.
WARNING:
ACL [BLACK]
ACN [WHITE]
G GREENROUND [ ]
Each FFHS/2 Series fixture is provided with a Junction Box that contains wire
Connectors and a Surge Protector. The Surge Protector is required! The Surge
Protector is pre-installed, fastened with a screw inside the Junction Box. Please follow
the wiring diagram below.
Screw
Hole
Surge Protector
Connector
2
1
3
2
3
Copyright © 2021 PacLights All Rights Reserved Note: Instructions are subject to change at any time without notice
The Optional Slip Fitter mount AC-FHS-SF provides a tilt option for the FFHS/2
Luminaire. There are several sizes for the FFHS/2 Series. The AC-FHS-SFS is for
the FFHS/2-400/500 Luminaire. The AC-FHS-SFM is for the FFHS/2-600/750
Luminaire. The AC-FHS-SFL is for the FFHS/2-1000/1200 Luminaire. Align the
Slip Fitter to the FFHS/2 Handle and fasten the two pieces together using the
[4] Hex Head Bolts and nuts.
FF FHS/2 Series LED lood Light Installation Sheet
Once the Slip Fitter is properly
secured onto the FFHS/2 Fixture,
one can then run the Power Cable
from the Fixture to the inside of the
pole to allow it to be powered with
an AC Power Supply Cable. Follow
the wiring diagram. One can then
place the Slip Fitter on top of a
standard 2 3/8” diameter pole, adjust
the orientation and fasten the [4] Hex
Head Bolts to secure the Slip Fitter
to the pole.
02-00036-211214
After properly securing the FFHS/2 Luminaire
with the Slip Fitter to the pole, if needed, adjust
directly at the Slip Fitter by removing the Phillips
head screws, the cover, loosening the bolt with
a wrench, and pulling slightly to move the parts
freely from the teeth. After adjusting the Slip
Fitter tilt, mate the parts at the teeth and fasten
the bolt, put the cover in place, install the screws.
Ø2 3/8”
The Optional Glare Shield AC-FHS-GS provides a restriction for excess glare by
the FFHS/2 Luminaire. There are several Glare Shields for the FFHS/2 Series. The
AC-FHS-GSS is for the FFHS/2-400/500 Luminaire, the AC-FHS-GSM is for the
FFHS/2-600/750 Luminaire, and the AC-FHS-GSL is for the FFHS/2-1000/1200
Luminaire. The Glare Shield restricts the amount of light pollution and light trespass.
Align the Glare Shield to the front of
the FFHS/2 fixture holes along the rim.
Fasten the Glare Shield to the fixture
with the [5] Socket Head Cap screws.
Bolts
Bolts
Bolts
Teeth
Screws
Bolt
Screws
Glare Shield
Glare Shield
Glare Shield
Slip Fitter
FFHS/2 Handle
Pole
Cover
Optional Glare Shield
Optional Slip Fitter
The FFHS/2 Series have an Optional Photo Cell that can be attached to the Junction
Box at the side. The Photo Cell has three wires: Neutral [White], Hot [Black], and
Hot [Red]. The Neutral [White] attaches inline with the Power Supply and Fixture
ACN Neutral [Blue/White] wires. The Photo Cell has an internal ‘switch’ with a Hot
[Black] wire that attaches to the Power Supply Hot [Black] and a Hot [Red] wire that
attaches to the Fixture ACL [Brown/Black] wire. Mounting is recommended in the
upright position. Please follow the wiring diagram as shown.
Optional Photo Cell
HOT [RED]
NEUTRAL [WHITE]
HOT [BLACK]
Slip Fitter
Glare Shield
HOT [BLACK]
NEUTRAL [WHITE]
HOT [RED]
PHOTO CELL
Page 2 of 2
AC Power Supply FFHS/2 FIXTURE
ACN [ /WHITE]BLUE
ACL [ /BLACK]BROWN
G GREENROUND [ ]
FFHS/2 Handle
JUNCTION BOX
1
2
3
1
2
11
2
2
3
This manual suits for next models
6
Other PacLights Floodlight manuals
