Palmetto Craft GLIDER User manual

GLIDER
ASSEMBLY INSTRUCTIONS BEST TOOLS NEEDED
FOR ASSEMBLY
Drill
Socket
Hammer
HARDWARE INCLUDED:
(4) ball bearing straps
(8) 2 ½” bolts
(6) 4” bolts
(1) 2 ¼” bolt
(8) ½” nylonuts
(8) ½” standard nuts
(15) washers
(12) 2” screws
(7) Nuts –7/16”
Bench Assembly
1) Place pre-assembled seat on a level surface. Align 3
pre-drilled holes on seat with the 3 pre-drilled holes on
pre-assembled back supports (see figure 1).
2) Secure ONLY center support with 2 ¼” bolt, washer
and nut. Hand tighten. Left and right supports will be
secured with the attachment of arm/leg assembly (see
figure 2).
3) Position arm/leg assembly to side of bench - curved
side in (see figure 3). Use 4” bolt, washer, and nut to
attach back of arm/leg assembly to back support
through pre-drilled hole. Use (2) 4” bolts, washers, and
nuts to attach arm/leg assembly to seat through
pre-drilled holes. Hand tighten.
4) Repeat to attach arm/leg assembly at opposite end
of bench.
Base Assembly
5) Stand pre-assembled footers on a level surface with
vertical supports on the inside (see figure 4).
6) Position 42” stringer boards between footers and
attach using the 2“ screws in the three pre-drilled holes
in the stringer boards (see figure 4).
7) Insert 2 ½" bolt through pre-drilled hole in footer
(see figure 5), add washer and regular nut. Wrench
tighten. Place ball bearing strap on bolt (note curve in
figure 6), followed by nylonut. Wrench tighten.
Repeat on back of footer. Repeat to attach ball bearing
straps on other side of base.
Combining Bench and Base Assemblies
8) Place completed bench assembly over the
completed base assembly, taking note of front and
back of the base (see base orientation in figure 7).
9) Insert 2 ½” bolt through pre-drilled hole in bottom of
front leg (see figure 8), add washer and regular nut. Wrench tighten. Place ball
bearing strap on bolt (see orientation in figure 9) followed by nylonut. Wrench
tighten. Repeat on back leg. Repeat to attach ball bearing straps on other side of
glider.
10) Wrench tighten all nuts and bolts.
Important Note:
Your furniture has been kiln-dried and
ready to stain, paint or water seal to
help preserve it and keep it looking
nice longer. Please note, exposure of
all woods to outdoor elements can
cause fading, warping, cracking,
shrinking or expansion. The
manufacturer and distributor of this
product cannot be held responsible for
damage or changes caused by
natural weathering.
QUALITY AMISH-MADE FURNITURE
Finished Base, Front View
For support, contact [phone], [e-mail], or visit palmettocraft.com
Complete assembly videos can be found on palmettocraft.com

Bench Assembly
1) Place pre-assembled seat on a level surface. Align 3
pre-drilled holes on seat with the 3 pre-drilled holes on
pre-assembled back supports (see figure 1).
2) Secure ONLY center support with 2 ¼” bolt, washer
and nut. Hand tighten. Left and right supports will be
secured with the attachment of arm/leg assembly (see
figure 2).
3) Position arm/leg assembly to side of bench - curved
side in (see figure 3). Use 4” bolt, washer, and nut to
attach back of arm/leg assembly to back support
through pre-drilled hole. Use (2) 4” bolts, washers, and
nuts to attach arm/leg assembly to seat through
pre-drilled holes. Hand tighten.
4) Repeat to attach arm/leg assembly at opposite end
of bench.
Base Assembly
5) Stand pre-assembled footers on a level surface with
vertical supports on the inside (see figure 4).
6) Position 42” stringer boards between footers and
attach using the 2“ screws in the three pre-drilled holes
in the stringer boards (see figure 4).
7) Insert 2 ½" bolt through pre-drilled hole in footer
(see figure 5), add washer and regular nut. Wrench
tighten. Place ball bearing strap on bolt (note curve in
figure 6), followed by nylonut. Wrench tighten.
Repeat on back of footer. Repeat to attach ball bearing
straps on other side of base.
Combining Bench and Base Assemblies
8) Place completed bench assembly over the
completed base assembly, taking note of front and
back of the base (see base orientation in figure 7).
9) Insert 2 ½” bolt through pre-drilled hole in bottom of
front leg (see figure 8), add washer and regular nut. Wrench tighten. Place ball
bearing strap on bolt (see orientation in figure 9) followed by nylonut. Wrench
tighten. Repeat on back leg. Repeat to attach ball bearing straps on other side of
glider.
10) Wrench tighten all nuts and bolts.
Figure 5 Figure 6
Figure 8 Figure 9
Figure 7: Back, note extension
Figure 1 Figure 2 - center back support Figure 3
Figure 4
Lorem ipsumvv
For support, contact [phone], [e-mail], or visit palmettocraft.com