PAMAPIC JHB-1500R Dimensions and installation guide

INFRARED HEATER
THE USER MANUAL AND WARRANTY CERTIFICATE
Model:JHB-1500R
If you have any problem, please do not hesitate to contact us via
email:[e-mail]
We will respond to you at our earliest time(within 24h)! Your satisfaction is our greatest pursuit!
Warm regards

WARNING!
PLEASE DO NOT USE THIS PRODUCT IN THE VERTICAL
POSITION
Distinguished Customer,
This manual has been designed for our Infrared Line, Infrared Star and Infrared U K
Line models.
You have purchased a high quality, efficient and original Infrared Heater.
We would like to express our gratitude to you for your appropriate choice and confidence
in our company. Please read this manual thoroughly in order to attain a sustainable
satisfaction with your heater.
Appropriate installation, operation and maintenance are of great importance for the
security of you and of those who are to benefit from the heater.
The difference between Infrared Classic, Infrared Line and Infrared Star models is the
duration of lives of the filaments employed.
Please keep this manual in a safe place for future reference and urgent needs.
We wish you to enjoy your new Infrared Heater for better days and times.
All Infrared Products have CE/GS/EMC/ETL/ROHS certificate.

1. Table of contents
1. Table of contents
2. Safety
2.1 Safety Instructions (A+B)
2.2 Safety Instructions (C+D)
3. Installation
3.1 Installation Instructions
3.2 Installation Instructions Position + Distance
3.3 Installation Instructions with Right and Wrong Positions
4. Using steps
5. Application Fields
6. Specifications
7. Operating Instructions
7.1 Definitions of the Buttons on the Remote Control
7.2 Operation of the Remote Control
7.3 Manual Operation
8. Cleaning and Maintenance Instructions
9. Technical Service
10. Terms of Warranty

2. Safety
2.1 Safety Instructions (A+B)
A-Electrical Connection Safety
Check whether your appliance and power cord are damaged before operating your
appliance.
Check whether there is any crack, disjoint or scratch on the filament (heating tube). If
any, contact with your authorized technical service.
If you appliance or power cord is damaged, do not operate your appliance and return
it to your technical service.
Make sure that the main electricity circuit is 220-240V and 110-120V, 50-60Hz and
the connection is fused.
Check the safety of the network. The fuse must be 25A.
Do not use your infrared heater together with another appliance plugged to the same
multiple sockets or connected to the same fuse.
Use your appliance with a properly earthed plug.
The earthed plug must fall outside heating field and hot surface.
The power cord must not be left on or around the frame of your infrared appliance.
Unplug your appliance when you won’t operate it for a long term or will conduct
cleaning or maintenance.
The damaged heater glass must be exchanged.
If the cable of the heater should be damaged, this may be replaced only by the
authorized service.
If has to be notified that the mounting in the bath must be so that the persons in the
bath can not reach the controls.
It has to be notified that the product has to be installed at a dry location and may not
be wet.
B-Safe distances required for installation on the wall, high temperature and fire protection
Attention! The appliance must only be operated in a horizontal position with
max±15°slope. In case of operations in angels larger than 5°in horizontal position or
of vertical operations, the heating loop wire may fall into disuse shortly.
Never install your appliance on a combustible surface (carton etc.)
The distance of your appliance from the ground is to min 1.8 m (6 feet).
The distance of your appliance from the ceiling is to be min 0.7 m (2.5 feet).
The distance of your appliance from the living beings is to be min 1 m (3.5 feet).
The distance of heating area of your appliance from the materials such as wood,
carton, cloth etc., must be min 1 m (3.5 feet).
Do not cover your appliance and do not hang any clothing over the heater or do not
place any clothing on or near the appliance.
Do not stick anything into the protective grid.

Do not make use of your heater to light up cigarette or similar materials.
Supervision is needed when this product is used anywhere near children. The
appliance is not intended for use by children or other persons without assistance or
supervision if their physical, sensory or mental capabilities prevent them from using it
safely.
Risk of Fire-keep combustible material such as furniture, papers, cloths, and curtains
at least 0.9 m (3 feet) from the front of the heater and away from the sides and rear.
Warning-TO REDUCE THE RISK OF FIRE
1) Do not place any objects such as furniture, papers, cloths, and curtains at least 0.9m
(3 feet) from the front of the heater and away from the sides and rear when the heater
is plugged in.
2) Do not place the heater near a bed because objects such as pillows or blankets can
fall off the bed and be ignited by the heater.
3) Always unplug the heater if it is not being used.
4) Avoid the use of an extension cord because the extension cord may overheat and
cause a risk of fire. However, if you have to use an extension cord, the cord shall be
14 AWG minimum size and rated not less than 2000 watts.
5) Do not operate within 7.6 m (25 feet) of flammable material.
Never block the front grill of the heater.
The heater is not suitable for hazardous locations.
Never attempt to service the heater without disconnecting its power source.
C-Cleaning and Maintenance Instructions
Unplug your heater first.
Never pull your power cable to Unplug power cable
unplug your heater

Take out the front grid to clean the reflector (reflecting mirror) and the filament and apply
the instructions on page 15.
D-Repair and Service (page 16)
Attention! Only technical services and persons authorized by professional
maintenance staff may serve, repair and replace the parts of this heater.
Distinguished Customer:
Please read safety instructions carefully for the security of you, your family and your
belongings before operating your appliance.
3. Installation
3.1 Installation Instructions
There are 4 brackets and fasteners used with the heater. Furthermore, in the
canal of back side of the heater there are 4 square fastener washers 25×25mm.
1Measure the installation position of the heater on the wall, and drill holes at
an appropriate distance on the wall parallel to the ground. (At least 1.8 m from the
floor and at least 0.5 m from the ceiling).
2Two brackets are fastened by the help of fasteners.

3Relieve the four 25×25mm square fastener washers in the canal on the back
of the heater and fasten 2 brackets to the canal of the backside of the heater by the
help of screws. The screws on the back of the heater should not be tightened too
tightly. You can move them until they are aligned with the wall.
4Align the bracket of the heater with the bracket on the wall.

5Join the brackets on the heater with the brackets, fastened on the wall, with
help of figured screw-nuts. Install the heater under necessary angle (in the
direction to the area being heated).
6You could loosen the screws connecting the heater bracket to the wall bracket
to change the best Angle of heating. Then retighten them.

7Electric wiring for the heater has to be done by the qualified specialist.
4.Using steps
Step 1：Connect the power line and the power strip.
Step 2：Turn on the side heater switch.

Step 3：Turn on the main power switch , which is standby. the digital screen shows P1,
the temperature reaches the first gear..
Step 4：Touch Switch Diagram Case ，the digital screen shows P2, the temperature
reaches the second gear.
Step 5：Touch Switch Diagram Case ，the digital screen shows P3, the temperature
reaches the third gear.

Step 6: Turn on the timer next to the power switch, After the function is turned on, the
touch time can be adjusted at will for 1-24 hours to stop at a fixed time. The digital screen
shows 0.1 for 1 hour and 0.2 for 2 hours.
5. Application Fields
Install the heater strict in horizontal position i.e.
PARALLEL TO FLOOR
Direct the heater the APPROPRIATE ANGLE

6. Specifications
Voltage
110-120V~
Frequency
60Hz
Electric power(W)
1500W
Product size
690*80*180mm
Product weight
2.1kg
7. Operating Instructions
7.1 Definitions of the Buttons on the Remote Control
The functions of the heater may be controlled via the buttons on your remote control and
LED screen. You may also control some of the functions of your heater through the
buttons on the front side of the heater.
Remote Control

1. On / Off
Switches on or off the heater or stands it by.
2. P1
After turn on the heater, you can choose low heating.
3. P2
After turn on the heater, you can choose moderate heating.
4. P3
After turn on the heater, you can choose high heating.
5. Time
Adjust the timer function.
Warning!
Insert the batteries of your remote control.
Notice:
1- Replace the old batteries with the same type batteries. Otherwise, your heater may
not function well.
2- Pull out the batteries in case of long terms of disuse to prevent leakage which may
impair your remote control.
7.2 Operation of the Remote Control
1. Turn on the power, the buzzer on the products will beep once, the digital screen and the
indicator is no show. At this time, press On / Off button to make it in stand by mode.
2. Press the function button to choose the power level. P1 indicator appears on the screen,
and the indicator flashes three times, indicating that the appliance is in low-grade mode.
Press the function button again to mid-grade, the buzzer will beep once, P2 indicator
appears on the screen, and the indicator flashes three times, indicating that the appliance
is in mid-grade mode. Press the function button again to high-grade, the beeper will beep
once, P3 indicator appears on the screen, and the indicator flashes three times, indicating
that the appliance is in high-grade mode. Press the function button again, you can choose
low, medium and high gear. Press ON / OFF button on the remote control or the heater
itself to switch off the heater.
3. In stand-by mode, press the timer button, the appliance can set time from 1 to 24 hours.
After set the time, the indicator next to the digital tube will light up, it means that the
appliance has been selected timer function. "0" indicates time not set.
4. When the appliance is on working, the digital screen always shows the power state
(P1-P2-P3). The timer setting, when the indicator lights up, it means that the machine has
been set a timer function from 1 to 24 hours. To view the regular time, press the timer
button, the appearing time is the present setting time, at this time the indicator also flashes
three times continuously, indicating that the appliance enters into the timer setting state.

7.3 Manual Operation
Control through the main module on the heater:
1.Control through the main module on the heater:
The 1st digit on the screen illustrates P symbol while 2nd digit illustrates power level mode
from 1 to 3.
2.After pressed ON / OFF button, the power level mode (P1, P2, P3)can be adjusted
through the buttons on the switch on heater. Continuously press the function button,
“Stand-by ---Low-grade---Mid-grade---High-grade---Stand-by” appears on the screen as a
circulation.
3.Press the timer button to make the timed hours appear on the heater screen.
8. Cleaning and Maintenance Instructions
Maintenance
Attention! Careful and regular maintenance of Infrared Heater considering our instructions
assume great importance so as to attain a long and efficient operation of your appliance.
1- Check the filthiness of the Reflector and IR-Filament at least once a month. If
necessary, apply cleaning and maintenance instructions.
2- The number of checks may be increased considering the amount of the dust in the
environment.
3- Check the deformation of the Reflector, Wire and Frame visually while cleaning the
appliance. In case of any deformation, consult to your technical service.
4- Check the power cord and plug visually while cleaning the appliance. In case of any
deformation, consult to your technical services.
5- It is recommended to change the reflector every 2 years for the purpose of more
efficient operation of your appliance.

Cleaning
Attention! Regular and careful cleaning helps your heater operate for longer years and
more efficiently.
1- Unplug your power cord for your safety before cleaning your appliance.
2- Press the grid wire of the heater and then remove it.
3- Make sure that the power is off for your safety. Power cord plug must be unplugged.
4- The reflector and filament must be cleaned with a soft cloth, a smooth brush or cool or
dry air. The cloth may be damp but never too wet and the cleaner should not include
any chemical.
5- Refrain from using cleaning material likely to damage the reflector (cleanser etc.).
6- Put the grid wire back on the heater and press the grid wire to fit it in.
9. Technical Service
Attention!
Only technical services and professional maintenance personnel may serve, repair and
replace the spare parts of this heater.
Points to be considered before shipping the product to the technical service:
1- Make sure that the thermostat of your appliance is in “0”mode.
2- Make sure that the plug, to which the appliance is connected, has power, check the
fuse and power cord. If the plug lacks power, consult to an electrician.
3- Make sure that the appliance has been installed in accordance with the instructions in
the manual. If the installation is inaccurate, consult to technical service.
Call the dealer to get service

10. Terms of Warranty
Warranty by SUN does not cover the defects arising out of the improper use the appliance.
The warranty does not cover the situations below:
1- The damages and defects arising out of improper use.
2- The damages and defects having occurred during the transportation after the delivery
of the product to the customer by the company.
3- The damages and defects arising out of low or excessive voltage, ungrounded plug
usage, faulty electricity systems, operating the appliance in different voltage values
other than specified in the instructions.
4- The damages and defects arising out of fire and lightening.
5- The damages and defects arising out of repairs and maintenance by persons other
than Authorized Services.
6- The defects arising out of the breach of the instructions in the manual.
7- The damages and defects arising out of the transportation of the product instead of
repair.
Attention! Faulty maintenance and cleaning are not covered by the warranty.
1- The dust and polluters in the environment.
2- Damage in the reflector or filament due to faulty cleaning.
3- Faulty installation or dismantlement.
4- Operating with damaged filament, frame or power cord.
Above mentioned defects and services are not covered by the warranty.
Should this product be proven defective in workmanship or material, the consumer’s sole
remedies shall be such repair or replacement as provided by the terms of this warranty.
Under no circumstances shall SUN be liable for any loss or damage, direct, consequential,
or incidental, arising out of the use of or inability to use this product.
This warranty will be voided if the certificate of warranty lacks the stamp and signature of
the supplier as well as the date of purchase.
This warranty will become void if the serial number (if applicable), model number
identification, or brand have been wholly or partially removed or erased.
All products have CE/GS/EMC/ETL certificate.
This symbol on the product or its packaging indicates that the appliance cannot
be treated as normal domestic trash, but must be handed in at a collection point
for recycling electric and electronic appliances.