Panasonic CS-S9KKQ User manual

© Panasonic HA Air-Conditioning (M) Sdn. Bhd. 2009.
Unauthorized copying and distribution is a violation
of law.
Operating Instructions
Air Conditioner
Model No.
Indoor Unit Outdoor Unit
CS-S9KKQ CU-S9KKQ
CS-S12KKQ CU-S12KKQ
CS-S18KKQ CU-S18KKQ
CS-S24KKQ CU-S24KKQ
CS-S28KKQ CU-S28KKQ
QUICK GUIDE
QUICK GUIDE
GUÍA RÁPIDA
GUÍA RÁPIDA
F567176
ENGLISH 2 ~ 7
Before operating the unit, read these operating
instructions thoroughly and keep them for future
reference.
ESPAÑOL 8 ~ 13
Antes de utilizar la unidad, sírvase leer
atentamente estas instrucciones de
funcionamiento y conservarlas como futuro
elemento de consulta.

2
SAFETY PRECAUTIONS
To prevent personal injury, injury to others, or property damage, please
comply with the following.
Incorrect operation due to failure to follow instructions below may cause
harm or damage, the seriousness of which is classified as below:
WARNING
WARNING
This sign warns of death or serious injury.
CAUTION
CAUTION
This sign warns of injury or damage to
property.
The instructions to be followed are classified by the following symbols:
This symbol denotes an action that is
PROHIBITED.
These symbols denote an actions that
is COMPULSORY.
WARNING
WARNING
INDOOR UNITAND OUTDOOR UNIT
This appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concerning
use of the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not
play with the appliance.
Please consult authorized dealer or specialist to repair,
install, remove and reinstall the unit. Improper installation
and handling will cause leakage, electric shock or fire.
Do not install the unit in a potentially explosive or flammable
atmosphere. Failure to do so could result in fire.
Do not insert your fingers or other objects into the
air conditioner indoor or outdoor unit, rotating parts
may cause injury.
Do not touch the outdoor unit during lightning, it may cause
electric shock.
REMOTE CONTROL
Do not allow infants and small children to play with the
remote control to prevent them from accidentally swallowing
the batteries.
Thank you for purchasing
Panasonic Air Conditioner
TABLE OF CONTENTS
TABLE OF CONTENTS
SAFETY PRECAUTIONS2~3
REMOTE CONTROL 4~5
INDOOR UNIT 6
TROUBLESHOOTING 7
INFORMATION 14~15
QUICK GUIDE
BACK COVER
NOTE
NOTE
The illustrations in this manual are for
explanation purposes only and may
differ from the actual unit. It is subjected
to change without notice for future
improvement.
OPERATION CONDITION
OPERATION CONDITION
Use this air conditioner under the following
temperature range
Temperature (°C) Indoor
*DBT *WBT
COOLING Max. 32 23
Min. 16 11
Temperature (°C) Outdoor
*DBT *WBT
COOLING Max. 43 26
Min. 16 11
* DBT: Dry bulb temperature
* WBT: Wet bulb temperature

ENGLISH
3
CAUTION
CAUTION
INDOOR UNITAND OUTDOOR UNIT
Do not wash the indoor unit with water, benzene,
thinner or scouring powder.
Do not use for other purpose such as
preservation of food.
Do not use any combustible equipment in front of
the airflow outlet to avoid propagation fire.
Do not expose yourself directly to cold air for a
long period.
Do not sit or step on the unit, you may
fall down accidentally.
Do not touch the sharp aluminium fin,
sharp parts may cause injury.
Do not switch ON the indoor unit when waxing
the floor. After waxing, aerate the room properly
before operating the unit.
Do not install the unit in oily and smoky areas.
Ensure drainage pipe is connected properly.
Otherwise, leakage may occur.
Aerate the room regularly.
After long period of use, make sure the
installation rack is not deteriorate to prevent the
unit from falling down.
REMOTE CONTROL
Do not use rechargeable (Ni-Cd) batteries.
It may damage the remote control.
Remove the batteries if the unit is not going to be
used for a long period of time.
New batteries of the same type must be inserted
following the polarity stated to prevent
malfunction of the remote control.
WARNING
WARNING
POWER SUPPLY
Do not use modified cord,
joint cord, extension cord or
unspecified cord to prevent
overheating and fire.
Do not share the same power outlet with other
equipment to prevent overheating and fire.
Do not operate with wet hands to prevent electric
shock.
If the supply cord is damage, it must be replaced
by the manufacturer, its service agent or similarly
qualified persons in order to avoid a hazard.
It is strongly recommended to be installed
with Earth Leakage Circuit Breaker (ELCB)
or Residual Current Device (RCD) to prevent
electric shock or fire.
This equipment must be earthed to prevent
electrical shock or fire.
In case of emergency or abnormal conditions
(burnt smell, etc), turn off the power supply, and
please consult authorized dealer.
Prevent electric shock by switching off the power
supply when:
- Before cleaning or servicing.
- Extended non-use.
- Abnormally strong lightning activity.
Air Inlet
Air Inlet
Air Outlet
Air Outlet
Air Outlet
Air Outlet
Air Inlet
Air Inlet
Air Inlet
Air Inlet
Indoor
Unit
Power
Supply
Remote
Control
Outdoor
Unit

4
REMOTE CONTROL
5TOADJUST VERTICALAIRFLOW DIRECTION
(5 OPTIONS)
AIR SWING
• Keeps the room ventilated.
• In COOL/DRY mode, if AUTO is set, the louver swing
up/down automatically.
6TOADJUST AIRFLOW DIRECTION (5 OPTIONS)
(PAGE 5)
AIR SWING
• Keeps the room ventilated.
• In COOL/DRY mode, if AUTO is set, the louver swing
left/right and up/down automatically.
7TO MONITOR HUMAN PRESENCE
& ACTIVITY FOR ENERGY SAVING
ECO
PATROL
ECO 1 ECO 2 ECO OFF
+3°C
Heat Source & Movement Low High
+2°C
Set Temperature
None
-1°C
Set Fan Speed
≤Medium
Fan
+1 tap
• — ECO 1 - To optimize comfort and energy saving.
• --- ECO 2 - To maximize energy saving.
MILD
DRY
FAN
SPEED
AIR
SWING
QUIET
POWERFUL
FAN SPEED
AIR SWING
ECO
PATROL PATROL/
MILD DRY
COOLING
MODE
TEMP
OFF/ON
TIMER
SET
CANCEL
ON
OFF
123
SET CHECK CLOCK RESET
AC RC
AUTO
COOL
DRY
Press the remote control’s button
1TO TURN ON OR OFF THE UNIT
• Please be aware of the OFF indication on the remote
control display to prevent the unit from starting/stopping
improperly.
2TO SET TEMPERATURE
• Selection range: 16˚C ~ 30˚C.
• Operating the unit within the recommended temperature
could induce energy saving.
COOL mode : 26˚C ~ 28˚C.
DRY mode : 1˚C ~ 2˚C lower than room temperature.
3TO SELECT OPERATION MODE
AUTO mode - For your convenience
• During operation mode selection the power indicator
blinks.
• Unit selects operation mode during startup according to
temperature setting and room temperature.
COOL mode - To enjoy cool air
• Use curtains to screen off sunlight and outdoor heat to
reduce power consumption during cool mode.
DRY mode - To dehumidify the environment
• Unit operates at low fan speed to give a gentle cooling
operation.
4TO SELECT FAN SPEED (5 OPTIONS)
FAN
S
PEED
• For AUTO, the indoor fan speed is automatically adjusted
according to the operation mode.
Maximum
distances: 8m
INDICATOR
PATROL SENSOR (Red/Orange/Blue)
POWER (Green)
TIMER (Orange)
QUIET (Orange)
POWERFUL (Orange)
(Blue)
ECO PATROL (Green)
S9KKQ, S12KKQ
4
5
2
11
3
10
12
13
15
Remote
Control display
14
7
9
1
8

ENGLISH
5
NOTES
NOTES
PATR
O
L/
,
Q
UIET
,
P
O
WERFUL
,
ECO
PATROL
• Can be activated in all modes and can be cancelled
by pressing the respective button again.
Q
UIET
,
P
O
WERFUL
,
ECO
PATROL
• Cannot be selected at the same time.
• Cannot be activated during “MIILD DRY COOLING”
operation is activated.
TO SET THE TIMER
TO SET THE TIMER
• 2 sets of ON and OFF timers are available to turn ON
or OFF the unit at different preset time.
• Complete below procedures to set each timer:
ON
OFF
1
Cancel
Cancel 2
S
ET
Select ON or OFF timer Set the
time Confirm
• Example of application at living room:
Morning: ON at 07:00 (Wake up)
OFF at 08:00 (Out for work)
Evening: ON at 17:00 (Back home)
OFF at 22:00 (Sleep)
• To cancel ON or OFF timer, press
O
Nor OFF to
select respective or then press CANCEL.
• If timer is cancelled manually or due to power failure,
you can restore the timer again by pressing
O
Nor
OFF to select respective or then press SET .
• Upcoming timer will be displayed and will be activated
in sequence.
• When ON Timer is set, the unit may start earlier (up
to 15 minutes) before the actual set time in order to
achieve the desired temperature on time.
• Timer operation is based on the clock set in the
remote control and repeats daily once set. For clock
setting, please refer to Remote Control Preparation at
back cover.
FAN SPEED
ECO
PATROL PATROL/
MILD DRY
COOLING
MODE
QUIET
TEMP
OFF/ON
AIR SWING
POWERFUL
TIMER
SET
CANCEL
ON
OFF
123
SET CHECK CLOCKRESE
AC RC
8TO ENJOY CLEAN & FRESH AIR
PATROL/ PATROL
NORMAL
PATROL - To monitor air quality
• Detects air quality; e-ion operation
activates when air quality is at dirty
level.
• Regardless of air quality, to
maintain air freshness e-ion
activates automatically (PATROL
SENSOR indicator turns red) when:
- 2 minutes after the unit is on, or
- exceeds 4 hours at clean level.
Indicator Air Quality
Blue Clean
Orange Moderate
Red Dirty
• Can be activated even when the unit is turned off.
• Patrol starts automatically with the unit switched on with
OFF/ON
.
- To freshen and purify the air
• Generates negative ions to produce fresh air effect and
attract dust which will then be captured at the positively
charged e-ion filters.
• Can be activated even when the unit is turned off. In this
condition, fan speed and air swing can not be adjusted.
9TO IMPROVE HUMIDITYAND MOISTURE LEVEL
• This operation reduces air dryness and provides you with
a comfortable living environment during COOL mode only.
• When vertical airflow direction is set to AUTO, it stops at
lower position to avoid cold air contact. However, you can
adjust the louver direction manually.
10 TO ENJOY QUIET OPERATION
• This operation reduces airflow noise.
11 TO REACH TEMPERATURE
QUICKLY
• This operation will stop automatically after 4 hours.
12 Press and hold for 5 seconds to dim or restore the
unit’s indicator brightness.
13 Press and hold for approximately 10 seconds to
show temperature setting in °C or °F.
14 Press to restore the remote control’s default setting.
15 Not used in normal operations.
S18KKQ, S24KKQ, S28KKQ
6

6
1INDOOR UNIT
• Wipe the unit gently with a soft, dry cloth.
2FRONT PANEL
Remove Front Panel
• Raise and pull to remove the front panel.
• Wash gently and dry.
Close Front Panel
• Press down both ends of the front panel to close it
securely.
3REMOTE CONTROL RECEIVER
4ALUMINIUM FIN
5ECO PATROL SENSOR
6HORIZONTALAIRFLOW DIRECTION LOUVER
S9KKQ, S12KKQ
• Manually adjustable.
S18KKQ, S24KKQ, S28KKQ
• Do not adjust by hand.
7VERTICALAIRFLOW DIRECTION LOUVER
• Do not adjust by hand.
8AUTO OFF/ON BUTTON
• Use when remote control is misplaced or a malfunction
occurs.
Action Mode
Press once. Auto
Press and hold until 1 beep is
heard, then release. Cooling
Press the button to turn off.
9e-ion CHARGING WIRE
10 e-ion FILTERS
• Clean the filters regularly.
• Wash/rinse the filters gently with water to avoid damage
to the filter surface.
• Dry the filters thoroughly under the shade, away from
fire or direct sunlight.
• Replace any damaged filters.
11 ACTIVE e-ion GENERATOR
Clean with dry cotton bud.
• Active e-ion generator cleaning is
recommended every 6 months.
CAUTION
•Switch off the power supply before cleaning.
•Do not touch the aluminium fin, sharp parts may cause injury.
INDOOR UNIT
5ECO PATROL SENSOR
• Do not hit or violently press the
sensor or poke it with a sharp
object. This can lead to damage
and malfunction.
• Do not place large objects near
the sensor and keep heating units
or humidifiers off the sensor’s
detection area. This may lead to
sensor malfunction.
2
3
5
7
8
1
4
6
9
10
11
9, 10 , 11 e-ionAIR PURIFYING
SYSTEM
• Do not touch during operation
CLEANING INSTRUCTIONS
CLEANING INSTRUCTIONS
HINT
HINT
• Do not use benzene, thinner or scouring powder.
• Use only soap ( pH7) or neutral household detergent.
• Do not use water hotter than 40°C.
• To ensure optimal performance of the unit, cleaning
maintenance has to be carried out at regular intervals.
Dirty unit may cause malfunction and you may see error
code “H99”. Please consult authorized dealer.

ENGLISH
7
TROUBLESHOOTING
The following symptoms do not indicate malfunction.
The following symptoms do not indicate malfunction.
SYMPTOM
SYMPTOM
CAUSE
CAUSE
Mist emerges from indoor unit. ►• Condensation effect due to cooling process.
Water flowing sound during operation. ►• Refrigerant flow inside the unit.
The room has a peculiar odour. ►• This may be due to damp smell emitted by the wall,
carpet, furniture or clothing.
Indoor fan stops occasionally during automatic fan speed
setting.
►• This helps to remove the surrounding odours.
Operation is delayed a few minutes after restart. ►• The delay is a protection to the unit’s compressor.
Outdoor unit emits water/steam. ►• Condensation or evaporation occurs on pipes.
Timer indicator is always on. ►• The timer setting repeats daily once set.
Power indicator blinks before the unit is switched on. ►• This is a preliminary step in preparation for the operation
when the ON timer has been set.
Cracking sound during operation. ►• Changes of temperature cause the expansion/contraction
of the unit.
Inconsistent airflow during PATROL operation. ►• Fan speed is adjusted automatically during patrol
operation.
Select QUIET operation to maintain the airflow
consistency.
Check the following before calling for servicing.
Check the following before calling for servicing.
SYMPTOM
SYMPTOM
CHECK
CHECK
Cooling operation is not working efficiently. ►• Set the temperature correctly.
• Close all doors and windows.
• Clean or replace the filters.
• Clear any obstruction at the air inlet and air outlet vents.
Noisy during operation. ►• Check if the unit has been installed at an incline.
• Close the front panel properly.
Remote control does not work.
(Display is dim or transmission signal is weak.)
►• Insert the batteries correctly.
• Replace weak batteries.
The unit does not work. ►• Check if the circuit breaker is tripped.
• Check if timers have been set.
The unit does not receive the signal from the remote
control.
►• Make sure the receiver not obstructed.
• Certain fluorescent lights may interfere with signal
transmitter. Please consult authorized dealer.
Patrol sensor or e-ion indicator on the indoor unit is
blinking.
►• Stop Patrol or e-ion operation then restart. If the patrol
sensor or e-ion indicator still blinking, please consult
authorized dealer.
Notes on “ECO PATROL SENSOR”
Notes on “ECO PATROL SENSOR”
• Sensor may not detect moving objects further than 7m away or beyond detection angle.
• Sensor sensitivity is influenced by indoor unit location, movement speed, temperature range, etc.
• The sensor may mistakenly detects pets, sunlight, certain lighting, fluttering curtains and light reflection as human being.
The unit stops and the timer indicator blinks.
Use remote control to retrieve error code.
TIMER
SET
CANCEL
ON
OFF
123
SET CHECK CLOCK RESET
AC RC
1Press for 5
seconds.
3Press for 5
seconds to
quit checking.
2Press until you hear
beep sound, then
write down the error
code.
Note:
• For certain errors, you
may restart the unit for
limited operation with 4
beeps during operation
starts.
4Turn the unit off and reveal the error code to authorized dealer.

8
PRECAUCIONES DE SEGURIDAD
Muchas gracias por elegir una
unidad de aire acondicionado
Panasonic
CONTENIDO
CONTENIDO
PRECAUCIONES DE
SEGURIDAD 8~9
MANDO A DISTANCIA10~11
UNIDAD INTERIOR 12
LOCALIZACIÓN DE
AVERÍAS 13
INFORMACIÓN 14~15
GUÍA RÁPIDA
CUBIERTA TRASERA
NOTA
NOTA
Las ilustraciones de este manual
sirven únicamente para describir las
explicaciones y pueden no coincidir
exactamente con las del aparato
suministrado. Están sujetas a cambios
sin previo aviso con el fin de mejorar el
producto.
CONDICIONES DE
CONDICIONES DE
FUNCIONAMIENTO
FUNCIONAMIENTO
Utilice este aparato de aire acondicionado
dentro del siguiente intervalo de
temperaturas
Temperatura (°C) Interior
*DBT *WBT
ENFRIAMIENTO
Máx. 32 23
Mín. 16 11
Temperatura (°C) Exterior
*DBT *WBT
ENFRIAMIENTO
Máx. 43 26
Mín. 16 11
* DBT: Temperatura de bulbo seco
* WBT: Temperatura de bulbo húmedo
Para evitar lesiones personales, lesiones a terceros, o daños materiales,
cumpla lo siguiente.
El uso incorrecto por no seguir las instrucciones puede causar daños o
averías; su gravedad se clasifica con las indicaciones siguientes:
ADVERTENCIA
ADVERTENCIA
Esta indicación advierte del posible peligro
de muerte o de daños graves.
PRECAUCIÓN
PRECAUCIÓN
Esta indicación advierte de los posibles
daños o desperfectos materiales.
Las instrucciones que deben seguirse están clasificadas mediante los
siguientes símbolos:
Este símbolo denota una acción
que está PROHIBIDA.
Estos símbolos denotan acciones
que son OBLIGATORIAS.
ADVERTENCIA
ADVERTENCIA
UNIDAD INTERIOR Y UNIDAD EXTERIOR
UNIDAD INTERIOR Y UNIDAD EXTERIOR
Este aparato no debe ser utilizado por personas (incluyendo
niños) con discapacidades mentales, sensoriales o físicas,
o falta de experiencia y conocimiento, a menos que hayan
recibido formación o supervisión en relación al uso del
aparato por una persona responsable por su seguridad. Los
niños deberían estar supervisados para asegurar que no
juegan con el aparato.
Consulte a un distribuidor autorizado o especialista para
reparar, instalar, retirar y reinstalar la unidad. Una instalación
y uso incorrectos provocarán fugas, descargas eléctricas o
incendios.
No instale la unidad en ambientes potencialmente
explosivos o inflamables. En caso contrario, podría
provocar accidentes de incendios.
No introduzca los dedos u otros objetos en la
unidad exterior o interior del aire acondicionado,
ya que las partes rotatorias podrían provocarle
lesiones.
No toque la unidad exterior durante un relámpago, ya que
podría causar una descarga eléctrica.
MANDOA DISTANCIA
No permita que bebés y niños pequeños jueguen con el
mando a distancia para evitar que ingieran accidentalmente
las pilas.

ESPAÑOL
9
PRECAUCIÓN
PRECAUCIÓN
UNIDAD INTERIOR YUNIDAD EXTERIOR
UNIDAD INTERIOR Y UNIDAD EXTERIOR
No limpie la unidad interior con agua, benceno,
disolvente o limpiador en polvo.
No utilice la unidad para otros fines, como la
conservación de alimentos.
No utilice ningún equipo combustible delante de
la salida de aire pare evitar que se propague un
incendio.
No se exponga directamente al aire frío durante un
periodo prolongado de tiempo.
No se siente o pare sobre la unidad, se
podría caer accidentalmente.
No toque la filosa aleta de aluminio, las
piezas filosas pueden causar lesiones.
No encienda la unidad cuando encere el suelo.
Después de encerar, airee la habitación correctamente
antes de usar la unidad.
No instale la unidad en áreas aceitosas y ahumadas.
Asegúrese de que el tubo de drenaje esté conectado
correctamente. Si no es así, se podrían producir
fugas.
Ventile la habitación con regularidad.
Después de un largo periodo de uso, asegúrese
de que la ranura de instalación no se encuentre
deteriorada, para evitar que la unidad se caiga.
MANDOA DISTANCIA
No utilice pilas recargables (Ni-Cd).
Podría dañar el control remoto.
Extraiga las pilas si no va a utilizar la unidad durante
un periodo prolongado de tiempo.
Para que el mando a distancia funcione bien, es
necesario insertar las pilas según la polaridad
indicada.
Entrada
Entrada
de aire
de aire
Salida
Salida
de aire
de aire
Salida
Salida
de aire
de aire
Entrada
Entrada
de aire
de aire
Entrada
Entrada
de aire
de aire
Unidad
Interior
Fuente
de
energía
Mando a
Distancia
Unidad
Exterior
ADVERTENCIA
ADVERTENCIA
FUENTE DE ENERGÍA
No utilice un cable modificado,
unido con otro, un cable
de extensión o un cable
no especificado para evitar
sobrecalentamiento e incendios.
No comparta la misma salida eléctrica con otros
equipos para evitar el calentamiento e incendios.
No lo use con las manos mojadas para evitar
descargas eléctricas.
Para evitar riesgos, si el cable de alimentación
está dañado y es necesario cambiarlo, deberá hacerlo
el fabricante, un representante del servicio técnico o
una persona calificada.
Se recomienda altamente instalarlo con un disyuntor
de fuga a tierra (ELCB) o un dispositivo residual actual
(RCD) para evitar descargas eléctricas o incendios.
Este equipo deberá conectarse a tierra para evitar
descargas eléctricas o incendios.
En caso de emergencia o condiciones anormales (olor
a quemado, etc.), corte la alimentación de energía y
consulte al distribuidor autorizado.
Evite descargas eléctricas desconectando la
alimentación eléctrica cuando:
- Antes de limpiarlo o repararlo.
- Largo periodo en desuso.
- Tormentas eléctricas especialmente violentas.

10
MANDO A DISTANCIA
5
PARAAJUSTAR LA DIRECCIÓN VERTICAL DE LA
CORRIENTE DEAIRE (5 OPCIONES)
AIR SWING
• Mantiene la habitación ventilada.
• En el modo FRÍO/SECAR, si AUTOMÁTICO está
configurado, la rejilla gira hacia arriba/abajo automáticamente.
6PARAREGULAR LA DIRECCIÓN DE LA
CORRIENTE DEAIRE (5 OPCIONES)
(PÁGINA 11)
AIR SWING
• Mantiene la habitación ventilada.
• En el modo FRÍO/SECAR, si AUTOMÁTICO está configurado,
la rejilla gira hacia la izquierda/derecha y arriba/abajo
automáticamente.
7
PARACONTROLAR LA PRESENCIA
HUMANAY LAACTIVIDAD PARA EL
AHORRO DE ENERGÍA
ECO
PATROL
ECO 1 ECO 2 ECO OFF
+3°C
Fuente de calor y movimiento
Baja Alta
+2°C
Temperatura configurada
Ninguna
-1°C
Definir la velocidad del ventilador
≤Ventilador
medio
+1 punto
• — ECO 1 - Para optimizar la comodidad y ahorro de energía.
• --- ECO 2 - Para el máximo ahorro de energía.
MILD
DRY
FAN
SPEED
AIR
SWING
QUIET
POWERFUL
FAN SPEED
AIR SWING
ECO
PATROL PATROL/
MILD DRY
COOLING
MODE
TEMP
OFF/ON
TIMER
SET
CANCEL
ON
OFF
123
SET CHECK CLOCK RESET
AC RC
AUTO
COOL
DRY
Distancia
máxima: 8m
INDICADOR
PATROL SENSOR
(Rojo/Naranja/Azul)
POWER (Verde)
TIMER (Naranja)
QUIET (Naranja)
POWERFUL (Naranja)
(Azul)
ECO PATROL (Verde)
S9KKQ, S12KKQ
4
5
2
11
3
10
12
13
15
Pantalla del
mando a
distancia
14
7
9
1
8
Pulse el botón del control remoto
1
ENCENDER OAPAGAR LA UNIDAD
• Por favor esté al tanto de la indicación OFF en la pantalla del
mando a distancia para impedir que la unidad arranqueo se
detenga incorrectamente.
2
PARAAJUSTAR LATEMPERATURA
• Gama de selección: 16°C ~ 30°C.
• El funcionamiento de la unidad dentro de la temperatura
recomendada podría resultar en el ahorro de energía.
MODO FRÍO : 26°C ~ 28°C.
MODO DESHUMIDIFICACIÓN : 1°C ~ 2°C menos que la
temperatura ambiente.
3
SELECCIONAR MODO DE OPERACIÓN
MODOAUTOMÁTICO - Para su conveniencia
• Durante la selección del modo de funcionamiento el indicador de
encendido parpadea.
• La unidad selecciona el modo de operación durante el inicio de
acuerdo a la configuración de la temperatura y a la temperatura
de la habitación.
MODO FRÍO - Para disfrutar de aire frío
• Use cortinas para proteger de luz solar y el calor exterior y así
reducir el consumo eléctrico durante el modo de frío.
MODO DESHUMIDIFICACIÓN - Para deshumidificar
el ambiente
• La unidad funciona en la velocidad de ventilador baja para
proporcionar una agradable refrigeración.
4
PARASELECCIONAR LA VELOCIDAD DEL
VENTILADOR (5 OPCIONES)
FAN
S
PEED
• Para AUTO (automático), la velocidad de ventilador de interior
es ajustada automáticamente según el modo de operación.