Panasonic CS-W50BTP User manual

1 SERVICE INFORMATION 3
2 FEATURES 4
3 SPECIFICATION (HEAT PUMP TYPE ) 9
4 SPECIFICATION (COOLING ONLY TYPE ) 10
5 TECHNICAL DRAWING 11
6 CIRCUIT DIAGRAM 13
7 OPERATING INSTRUCTION 25
8 REFRIGERATION CYCLE 27
9 OPERATION RANGE 28
10 PIPE LENGTH 29
11 OPERATING CHARACTERISTIC 31
12 FAN PERFORMANCE 32
© 2002 Matsushita Industrial Corporation. Sdn. Bhd.
(11969-T). All rights reserved. Unauthorized copying
and distribution is a violation of law.
CS-W50BTP CU-V50BBP8
CS-W50BTP CU-W50BBP8
13 SAFETY DEVICE 33
14 COMPONENT SPECIFICATION 34
15 CAPACITY AND POWER CONSUMPTION 35
16 DISCHARGE AND SUCTION PRESSURE 38
17 REACHING DISTANCE 39
18 SOUND DATA 40
19 TWIN AND TRIPLE 42
20 WIRING MISTAKE PREVENTION 47
21 TEST OPERATION AND SELF DIAGNOSIS 48
22 SETTING OF SAVE ENERGY AND THERMISTOR SWITCH 52
23 GROUP CONTROL 53
24 TROUBLESHOOTING 54
AIR CONDITIONER
CONTENTS
Page Page
ORDER NO. MAC0210059C2

25 EMERGENCY OPERATION 59
26 CONTROL 60
27 WIRED REMOTE CONTROL INSTALLATION MANUAL 70
28 WIRELESS REMOTE CONTROL INSTALLATION MANUAL 75
29 INSTALLATION (INDOOR UNIT) 82
30 INSTALLATION (OUTDOOR UNIT) 92
31 REPLACEMENT PARTS 104
2

1 SERVICE INFORMATION
Caution:
OPb free solder has a higher melting point than standard solder; Typically the melting point is 50 - 70°F (30 - 40°C) higher. Please use
a high temperature soldering iron. In case of the soldering iron with temperature control, please set it to 700 ± 20°F (370 ± 10°C).
OPb free solder will tend to splash when heated too high (about 1100° F/600°C).
Notice of Address setting for NEW Ceiling / NEW Outdoor Unit.
The new Ceiling / new Outdoor models are possible to have address setting for twin / triple control or group control
automatically when main power supply is switched on.
(Manual address setting is also possible by using DSW1 switch on the indoor unit P.C. board.) However, this address setting is
only possible when proper wiring connection is made and indoor unit must be of original unit.
1.1. Example of trouble during test operation
If the below phenomenon is found during test operation, wrong address setting is possible.
Therefore, please inspect the address setting.
1.LCD display of the wired remote control is not illuminated although the main power supply switch is ‘on’.
2.LCD display had indicated as normal illumination when power supply switch is ‘on’, however outdoor unit cannot be operated.
(But, it is necessary to take 3 to 5 minutes for outdoor unit to start from the timing of remote control OFF/ON button is ‘on’.)
(For normal operation, the outdoor unit will only start its operation after 3 to 5 minutes upon pressing the OFF/ON button.)
3.P.C. board had memorized wrong setting information.
a.If main power supply is switched on with the wrong connection.
b.When changing the connection or combination of units due to re-installation etc.
• • •
• When changing the system from twin to triple (triple to twin).
• • •
• When changing the system from group control to normal one to one system.
• • •
• When making the replacement of units of master and slave etc.
1.2. Caution during test operation
Do not touch the remote control button and do not change any wirings for one minute when the main power supply switch is ‘on’.
(Because the unit is having automatic address setting during the first one minute.)
1.3. Caution during automatic address setting
When the main power supply switch is ‘on’, the P.C. board will automatically memorize the connecting system.
Consequently, when initial power supply is ‘on’, there mustn’t be any interchanging of units even of the same type and same
capacity unit.
Therefore, connection of the unit to another system is prohibited.
3

2.1. New design
2.1.1. Gentle curved styling
• • •
• The base has gentle curves which express a functional
beauty. It spreads the air quietly over a wide area.
2.2. Such quietness!
2.2.1. Several new mechanism add up to
low 49 dB noise (W50BT - High
Fan Speed)
1.Delta throat fan
A delta throat (projection) has been attached to the fan
outlet to suppress the generation of vortexes. This helps
maintain air flow speed even at lower fan speeds and is
effective in reducing noise.
2.Reflux orifice
The orifice at the intake port is equipped with an air flow
guide which minimizes the flow disturbances which occur at
the orifice and inside the impeller.
This reduces pressure losses inside the casing and also
helps reduce noise.
3.Adoption of wing-shaped vanes
• • •
• The vanes of the fan have been changed to
“aerodynamic” shaped vanes, so that the air flow more
smoothly over the vane surfaces and noise is thus
suppressed.
• • •
• Side filters have been adopted in the pipe partitions.
These allow the air intake space to be increased and
also further reduce noise.
2.2.2. Automatic swinging louvre
• • •
• The horizontal air flow angle is a wide 100 degrees
(manual). The louvre can swing automatically (through 70
degrees vertically) using the remote control. This increases
the area of comfortable air flow and warms the air even to
floor level.
2.2.3. Newly-shaped louvre
• • •
• The newly-shaped louvre and air outlet effectively distribute
the air flow. During cooling, this stops warm air from
collecting near the louvre, and prevents freezing.
2 FEATURES
4

2.3. Easy installation
2.3.1. Easy suspension
• • •
• A suspension bolt fixing bracket with 4-point support is
attached to the main unit, which increases the space
available for installation.
2.3.2. Two installation methods :
standard and wall
• • •
• In addition to the standard (1) ceiling installation, a wall (2)
installation method (using a wall-hanging bracket) is
available for cases where the ceiling is too high for the main
unit to be suspended.
2.4. Piping
2.4.1. 3-direction pipe lead-out
• • •
• The refrigerant piping can lead out in one of three directions
(right, rear-right and top-right), and the drain pipe direction
can be selected from four directions (right, rear-right, left
and rear-left).
2.5. Easy maintenance
2.5.1. Long life filter (standard
equipment)
• • •
• In general office environments, cleaning (maintenance) is
not required until after approximately 2,500 hours of
operation, thus reducing maintenance work.
• • •
• For optimum comfort, it is recommended to clean the air
filter every 1-1/2 months.
2.5.2. Maintenance is possible from
underneath the unit.
• • •
• If the bottom panel is detached, the drain pan can then be
removed and installed from underneath the unit, and
inspection and servicing of component such as the control
panel also becomes easier.
2.6. Auto fan mode (indoor unit)
• • •
• Auto fan mode is added besides high, medium and low. It
automatically adjusts the fan speed according to the indoor
unit’s temperature.
2.7. Hot start system (heat pump
models)
2.8. Automatic changeover
function (heat pump models)
• • •
• The unit automatically switches between cooling and
heating in accordance with operating load in order to
maintain a comfortable indoor temperature.
5

2.9.1. Product features
• • •
• Low-noise design improves comfort in surrounding
areas
1.The noise-suppressing winglet fan is a result of new
research into vane design theory. The unique curved
shape suppresses the generation of vortexes, thus
reducing air flow noise.
2.The adoption of double-orifice rings reduces air
passage resistance.
3.Strengthening of the noise insulation materials in the
compressor and the sealing-in of mechanical noise
allows vibration noise to be greatly enclosed and
suppressed.
4.The heat exchanger has an L-shaped design to allow air
to flow more smoothly.
5.Noise is automatically reduced further during night-time
operation with lower outdoor air temperatures.
2.10. Greatly improved workability
increases system renewal
capability
• • •
• Pipes that are one size larger can also be connected for
renewal.
− − −
− If renewing the system, existing refrigerant pipes can be
utilized so that only the indoor and outdoor units need to
be replaced.
− − −
− For example, liquid and gas pipes from 10 years ago
can be connected to current pipes with the same size or
one size larger. Effective utilization of materials reduces
working time and trouble. (Adaptor sockets are not
supplied.)
2.9. Low-noise outdoor units
6

• • •
• Additional refrigerant charging unnecessary for 30 m
− − −
− All models do not require any additional charging of
refrigerant for 30 m of pipe length. This makes
installation much easier.
• • •
• Drain water dripping-prevention structure
− − −
− The base of the outdoor unit is provided with a single
drain hole in order to prevent drain water from leaking
out of the unit. By connecting a drain elbow and a
discharge pipe, water leakages can be prevented even
when the unit is installed to a wall.
• • •
• Save space design allows units to be installed side-by-
side continuously
− − −
− Servicing after installation can be carried out by
removing the front covers.
• • •
• Long pipe design for refrigerant pipes
− − −
− Maximum piping length of 50m for all models.
• • •
• Internal pipe connection
− − −
− Pipes are connected inside the units (inside the side
covers), making the final appearance more attractive.
− − −
− Pipes can be diverted outward in any of four directions
(forward, right, down, rear).
− − −
− Small liquid pipe diameters of 9.52mm for 50BB models,
making installation work much easier.
• • •
• Centralized draining method
− − −
− Even when multiple outdoor units are installed to a wall,
the drain outlets can be concentrated into a single drain
pipe. This makes installation easier and also improves
appearance.
2.11. A brand-new control method
using the latest in technology
• • •
• Easier power supply wiring connection
Power supply wiring and other wiring tasks can be carried
out more easily.
− − −
− Twin non-polar wires used to connect indoor and
outdoor units.
− − −
− Adoption of connection error prevention circuits for drive
wires and signal wires. If a connection error is made, the
relay does not operate and current does not flow to the
circuit boards.
• • •
• Twin and Triple operation
− − −
− Simultaneous air conditioning of wide spaces and
corners is possible. Indoor units of different
horsepowers can even be used in combination.
− − −
− Master unit and slave-units can be set automatically in
twin and triple systems. No address setting is
necessary.
− − −
− Multiple indoor units can be operated simultaneously
with a single remote control. Note that individual
operation is not possible.
• • •
• Separate indoor/outdoor unit power supplies
The power supply can be connected to (1) just the outdoor
units, or (2) to both the indoor and outdoor units.
• • •
• Easy test operation
Test operation can be carried out for both indoor and
outdoor units.
• • •
• Automatic setting initialization function (Remote control
and Indoor unit)
In accordance with the indoor and outdoor units connected
and the connection methods, conditions such as the
connection configuration (twin or triple format) and remote-
control functions such as automatic louvre operation and
cooling or heating mode are automatically detected and set
instantly.
7

2.12. Wired Remote Control
• • •
• The new design includes an easily-visible red pilot lamp.
The power can be turned on and off at a single touch,
without opening the cover.
• • •
• Has a built-in thermistor, allowing indoor temperature
detection in accordance with indoor conditions by switching
with main unit thermistor.
• • •
• Twin non-polar wires make installation work easy. (10 m
cable supplied as accessory.)
2.13. Wireless Remote Control
• • •
• New design with compact size. (Operation range within
approximately 8 m.)
• • •
• Built-in timer with ON/OFF timer setting (within 24 hours)
Wired Wireless
Heat Pump CZ-RD51P CZ-RL51P
Cooling CZ-RD51P CZ-RL01P
NOTE: Both of the above remote control is packed separately
from the indoor unit.
2.14. Group Control Equipment
8

3 SPECIFICATION (HEAT PUMP TYPE )
CS-W50BTP / CU-W50BBP8
ITEM / MODEL Indoor Unit Outdoor unit
Main Body CS-W50BTP CU-W50BBP8
Remote CZ-RD51P (Wired)
Control CZ-RL51P (Wireless)
Cooling Capacity kW 14.0
BTU/h 47,700
Heating Capacity kW 16.0
BTU/h 54,600
Refrigerant Charge-less m 30
Standard Air Volume for High Speed m3/min 35
cfm 1236
Outside Dimension (H x W x D) mm 250 x 1600 x 700 1220 x 1100 x 320
inch 9-27/32 x 62-31/32 x 27-9/16 48-1/24 x 43-5/16 x 12-19/32
Net Weight kg 47 115
lbs 104 254
Piping
Connection Refrigerant Gas mm (inch) O.D Ø 19.05 (3/4) Flared Type
Liquid mm (inch) O.D Ø 9.52 (3/8) Flared Type
Drain mm O.D Ø 20 I.D Ø 20 x 1
Compressor Type, Number of Set -Hermetic-1 (Scroll), 1
Starting Method - Direct on-line starting
Motor Type -2-pole 3-phase induction motor
Rated Output kW - 4.10
Fan Type, Number of Set Sirocco fan Propeller fan
Motor Type 4-pole single phase induction motor 6-pole single phase induction motor
Rated Output kW 0.14 0.055 x 2
Air-heat Exchanger Slit-fin type X-Louvre-fin type
Refrigerant Control Cool Capillary tube -
Heat - Capillary tube
Refrigerant Oil (Charged) litre - MMMAPOE
Refrigerant (Charged) kg - R407C (4.4)
(oz) (155)
Running
Adjustment Control Switch Wireless or Wired Remote Control -
Room Temperature Thermostat (Main Body) -
Safety Devices Internal protector for compressor, Internal thermostat for fan motor,
Crankcase heater, High and heating pressure switch, Current transformer
Noise Level dB (A) Hi 49 Lo 45 Cooling 56, Heating 58
Power level dB Cooling : Hi 66 Lo 62
Heating : Hi 66 Lo 62 Cooling 69, Heating 71
1.Cooling capacities are based on indoor temperature of 27°C D.B. (80.6°F D.B.), 19.0°C W.B. (66.2°F W.B.) and outdoor air
temperature of 35°C D.B. (95°F D.B.), 24°C W.B. (75.2°F W.B.)
2.Heating capacities are based on indoor temperature of 20°C D.B. (68°F D.B.) and outdoor air temperature of 7°C D.B.
(44.6°F D.B.), 6°C W.B. (42.8°F W.B.)
ELECTRICAL DATA (50Hz)
ITEM / MODEL CS-W50BTP, CU-W50BBP8
Condition by JIS B 8615
Volts V 380 400 415
Phase 3N 3N 3N
Power Consumption kW Cool 5.35 5.35 5.35
Heat 5.45 5.45 5.45
Running Current ACool 9.2 9.2 9.2
Heat 9.2 9.2 9.2
Starting Current A 69 69 69
Power Factor % Cool 88 84 81
Heat 90 86 82
*Power Factor means total figure of compressor, indoor fan motor and outdoor fan motor.
Panasonic Power source AC, 3N~380V, 400V, 415V 50Hz
9

4 SPECIFICATION (COOLING ONLY TYPE )
CS-W50BTP / CU-V50BBP8
ITEM / MODEL Indoor Unit Outdoor unit
Main Body CS-W50BTP CU-V50BBP8
Remote CZ-RD51P (Wired)
Control CZ-RL01P (Wireless)
Cooling Capacity kW 14.0
BTU/h 47,700
Refrigerant Charge-less m 30
Standard Air Volume for High Speed m3/min 35
cfm 1236
Outside Dimension (H x W x D) mm 250 x 1600 x 700 1220 x 1100 x 320
inch 9-27/32 x 62-31/32 x 27-9/16 48-1/24 x 43-5/16 x 12-19/32
Net Weight kg 47 112
lbs 104 247
Piping
Connection Refrigerant Gas mm (inch) O.D Ø 19.05 (3/4) Flared Type
Liquid mm (inch) O.D Ø 9.52 (3/8) Flared Type
Drain mm O.D Ø 20 I.D Ø 20 x 1
Compressor Type, Number of Set -Hermetic-1 (Scroll), 1
Starting Method - Direct on-line starting
Motor Type -2-pole 3-phase induction motor
Rated Output kW - 4.10
Fan Type, Number of Set Sirocco fan Propeller fan
Motor Type 4-pole single phase induction motor 6-pole single phase induction motor
Rated Output kW 0.14 0.055 x 2
Air-heat Exchanger Slit-fin type X-Louvre-fin type
Refrigerant Control Capillary tube Capillary tube
Refrigerant Oil (Charged) litre - MMMAPOE
Refrigerant (Charged) kg - R407C (4.4)
(oz) (155)
Running
Adjustment Control Switch Wireless or Wired Remote Control -
Room Temperature Thermostat (Main Body) -
Safety Devices Internal protector for compressor, Internal thermostat for fan motor,
Crankcase heater, High pressure switch, Current transformer
Noise Level dB (A) Hi 49 Lo 45 56
Power level dB Hi 66 Lo 62 69
1.Cooling capacities are based on indoor temperature of 27°C D.B. (80.6°F D.B.), 19.0°C W.B. (66.2°F W.B.) and outdoor air
temperature of 35°C D.B. (95°F D.B.), 24°C W.B. (75.2°F W.B.)
ELECTRICAL DATA (50Hz)
ITEM / MODEL CS-W50BTP, CU-V50BBP8
Condition by JIS B 8615
Volts V 380 400 415
Phase 3N 3N 3N
Power Consumption kW Cool 5.35 5.35 5.35
Running Current ACool 9.2 9.2 9.2
Starting Current A 69 69 69
Power Factor % Cool 88 84 81
*Power Factor means total figure of compressor, indoor fan motor and outdoor fan motor.
Panasonic Power source AC, 3N~380V, 400V, 415V 50Hz
10

5 TECHNICAL DRAWING
11

12

6 CIRCUIT DIAGRAM
13

14

15

16

17

18

19

20