Panasonic WV-Q122E User manual

Before attempting to connect or operate this product,
please read these instructions carefully and save this manual for future use.
The model number is abbreviated in some descriptions in this manual.
Wall Mount Bracket
Operating Instructions
Model No. WV-Q122E
The camera in the illustration is separately sold.

-2-
Front Cable Exit
1. Preparations
Specify the bracket fixing location, and then put in
four anchor bolts, or drill four bolt holes on the
installation surface. Refer to Dimensions on page 7.
2. Cable Bushing
Fit the supplied cable bushing into the front cable
exit of the bracket.
3. Cable Route
Route the connection cables from the front cable
exit through the bracket, and pull them out of the
pipe mouth.
4. Fixing Bracket
Fix the bracket to the wall using appropriate hard-
ware (not supplied): bolts and nuts, anchor bolts
and nuts, or the like.

Mark hole positions
Cable Bushing
Fixing Hardware
(Locally Procured)
■Introduction
This bracket is used for mounting the colour camera WV-CW960 or WV-CW964 onto a wall.
There are two ways of cable exit available from the front or rear of the bracket.
Precautions
•Make sure that the place you are installing the camera is strong enough to support it. If it is not strong enough, then the cam-
era may fall and hurt someone.
•The following steps of installation and connection work should be done by qualified service personnel or system installers
and should conform to all local codes.
•Be sure to turn the power off before installation and connection.
•Do not install the camera near the air outlet of an air conditioner.

-3-
5. Disassembly of Camera
(1) Remove the upper base from the camera by
loosening 3 screws. The screws that are
removed need to be used during reassembly.
Be careful to not lose them. Turn the upper base
and separate it.
* Special screw (mounting screw): Use a hexa-
gon wrench for the hexagon screw (M6).
(2) Remove the attachment pipe from the upper
base by loosening 4 screws.
* Special screw (mounting screw): Use a hexa-
gon wrench for the hexagon screw (M6).
6. Setting Switches
Refer to DIP SWITCH SETTINGS in the manual
included with the camera.
7. Cable Connection
Refer to CONNECTIONS in the manual included
with the camera.
Warning: Seal the cables with plastic or rubber
tape to prevent it from being exposed.
8. Mounting Upper Base
Fix the upper base to the bracket.
• Fasten 4 screws (the screws that were removed in
step (2) of “5. Disassembly of Camera”) making
sure that “REAR” engraved on the upper base faces
the wall.
9. Waterproofing
Fill the front cable exit with sealant.
Warning: Carefully apply the sealing so that water
or moisture cannot get inside. If water gets
inside the camera it could cause a shock or fire.
Also, if moisture gets inside the camera it could
cause the dome to become foggy.
10. Mounting Camera
(1) Aim the START arrow at the bent portion of the
leaf spring on top of the camera.
START
Sealant
Cable Bushing
Outside
Inside the bracket
Cables
Upper Base
Attachment Pipe
Camera Fixing Screw
x4
Upper Base
Bending Leaf Spring
Camera
x3
x4

-4-
(2) Be sure to hook the fall prevention wire to the
bracket.
(3) Fix the camera to the upper base.
• Move the camera up so that its guide pins fit into
the guide holes of the upper base.
• Turn the camera counter-clockwise to the end,
viewed from the bottom.
• Fasten 3 screws (the screws that were removed
in step (1) of “5. Disassembly of Camera”).
Caution: Tighten the three (3) mounting screws for
the upper base.
Recommended torque: Approximately 2.45 N/m
{24 kgf cm}
Poorly tightened screws may result in water
leaking into the camera or possible fire.
Fall Prevention Wire
x3
Upper Base
Camera

-5-
Rear Cable Exit
1. Preparations
Specify the bracket fixing location, and then put in
four anchor bolts (not supplied), or drill four bolt
holes on the surface.
Remember that a cable access hole is necessary on
the wall in this case.
Refer to Dimensions on page 7.
2. Rear Cable Exit
(1) Remove the rear plate, and then punch out the
cable exit on it.
(2) Fit the supplied blank bushing into the front
cable exit of the bracket.
(3) Fit the supplied cable bushing into the rear cable
exit of the plate.
(4) Replace the rear plate to the bracket fastening
four screws.
3. Cable Routing
Route the connection cables from the rear cable exit
through the bracket, and pull them out of the pipe
mouth.
4. Waterproofing
Fill the rear cable exit with sealant.
5. Fixing Bracket
Fix the bracket to the wall using appropriate hard-
ware (not supplied): bolts and nuts, anchor bolts
and nuts, or the like.

Cable Access Hole
on the wall
Front Cable Exit
(Not Used) Rear Cable Exit
Rear Plate
Blank Bushing Cable Bushing
Fixing Hardware
(Locally Procured)
Sealant
Cable Bushing
Outside
Inside the Bracket
Cables
Mark hole positions

-6-
6. Disassembly of Camera
(1) Remove the upper base from the camera by
loosening 3 screws. The screws that are
removed need to be used during reassembly. Be
careful to not lose them. Turn the upper base
and separate it.
* Special screw (mounting screw): Use a hexa-
gon wrench for the hexagon screw (M6).
(2) Remove the attachment pipe from the upper
base by loosening 4 screws.
* Special screw (mounting screw): Use a hexa-
gon wrench for the hexagon screw (M6).
7. Setting Switches
Refer to DIP SWITCH SETTINGS in the manual
included with the camera.
8. Cable Connection
Refer to CONNECTIONS in the manual included
with the camera.
Warning: Seal the cables with plastic or rubber
tape to prevent it from being exposed.
9. Mounting Upper Base
Fix the upper base to the bracket.
• Fasten 4 screws (the screws that were removed in
step (2) of “6. Disassembly of Camera”) making
sure that “REAR” engraved on the upper base faces
the wall.
10. Mounting Camera
(1) Aim the START arrow at the bent portion of the
leaf spring on top of the camera.
(2) Be sure to hook the fall prevention wire to the
bracket.
(3) Fix the camera to the upper base.
• Move the camera up so that its guide pins fit into
the guide holes of the upper base.
• Turn the camera counter-clockwise to the end,
viewed from the bottom.
• Fasten 3 screws (the screws that were removed
in step (1) of “6. Disassembly of Camera”).
Caution: Tighten the three (3) mounting screws for
the upper base.
Recommended torque: Approximately 2.45 N/m
{24 kgf cm}
Poorly tightened screws may result in water
leaking into the camera or possible fire.
START
Upper Base
Attachment Pipe
Camera Fixing Screw
x4
Upper Base
Bending Leaf Spring
Fall Prevention Wire
x3
Upper Base
Camera
Camera
x3
x4

-7-
■Specifications
Dimensions: 111.5(W) x 210.5(H) x 269(D) mm
Weight: 2 kg approx.
Weight and dimensions indicated are approximate.
Specifications are subject to change without notice.
■Accessories
Operating Instructions (this manual) ............................. 1 pc.
The following items are for installation.
Camera Fixing Screw (Hexagon screw (M6)) ...............4 pcs.
Cable Bushing ...............................................................1 pc.
Blank Bushing................................................................1 pc.
25
Ø58
269
80
（111.5）
180
(210.5)
4-Ø10
240
Unit: mm
(50)
(90)
30
Ø25.4
■Dimensions
Fall Prevention
Wire Hook
Rear Cable Exit
(Punch out the hole when using)
Camera Fixing
Screw Hole x4
Front Cable Exit

AM1105-2010 3TR004263CAA Printed in Japan