Panasonic H-E08018PP User manual

file:///C|/U...l/Temp/Rar$EXa0.719/viewing/SGML_VIEW_DATA/ALL/H-E08018PP/SVC/DSC1705017CE/doc/DSC1705017CE_cvr.xml[11/11/2018 4:59:45 PM]
ORDER NO.DSC1705017CE
B26
Interchangeable Lens for Digital Camera
Model No. H-E08018PP
H-E08018E
H-E08018GK
© Panasonic Corporation 2017 Unauthorized copying and distribution is a violation of law.

file:///C|/Users/z.bAShir/AppData/Local/Temp/Rar$EXa0.719/viewing/SGML_VIEW_DATA/ALL/H-E08018PP/SVC/DSC1705017CE/doc/DSC1705017CE_01.xml[11/11/2018 5:17:55 PM]
1 Safety Precautions
1.1 Information for Your Safety

file:///C|/Users/z.bAShir/AppData/Local/Temp/Rar$EXa0.719/viewing/SGML_VIEW_DATA/ALL/H-E08018PP/SVC/DSC1705017CE/doc/DSC1705017CE_01.xml[11/11/2018 5:17:55 PM]
1.2 Cautions for use

file:///C|/Users/z.bAShir/AppData/Local/Temp/Rar$EXa0.719/viewing/SGML_VIEW_DATA/ALL/H-E08018PP/SVC/DSC1705017CE/doc/DSC1705017CE_01.xml[11/11/2018 5:17:55 PM]

file:///C|/U...al/Temp/Rar$EXa0.719/viewing/SGML_VIEW_DATA/ALL/H-E08018PP/SVC/DSC1705017CE/doc/DSC1705017CE_02.xml[11/11/2018 5:03:34 PM]
2 Service Navigation
2.1 Introduction
This service manual contains technical information, which allow service personnel’s to understand and service this model
Please place orders using the parts list and not the drawing reference numbers.

2.2 Important Notice
2.2.1 About LENS MAIN UNIT (Ref. 220)
1. 
lens adjustments.

2. 
209), to maintain Serial number of owner's original lens. Fig. 1-1
3. No adjustment is required when replacing the part mentioned on Fig.1-1. But, when tighten the concerned screws,apply proper torque

file:///C|/U...al/Temp/Rar$EXa0.719/viewing/SGML_VIEW_DATA/ALL/H-E08018PP/SVC/DSC1705017CE/doc/DSC1705017CE_02.xml[11/11/2018 5:03:34 PM]
mentioned on "6. Disassembly and Assembly Instruction" section.

file:///C|/U...al/Temp/Rar$EXa0.719/viewing/SGML_VIEW_DATA/ALL/H-E08018PP/SVC/DSC1705017CE/doc/DSC1705017CE_03.xml[11/11/2018 5:08:18 PM]
3 Specifcations
3.1 Specifcations (Rated)

file:///C|/U...al/Temp/Rar$EXa0.719/viewing/SGML_VIEW_DATA/ALL/H-E08018PP/SVC/DSC1705017CE/doc/DSC1705017CE_03.xml[11/11/2018 5:08:18 PM]
3.2 Accessories

file:///C|/U...al/Temp/Rar$EXa0.719/viewing/SGML_VIEW_DATA/ALL/H-E08018PP/SVC/DSC1705017CE/doc/DSC1705017CE_03.xml[11/11/2018 5:08:18 PM]

file:///C|/U...al/Temp/Rar$EXa0.719/viewing/SGML_VIEW_DATA/ALL/H-E08018PP/SVC/DSC1705017CE/doc/DSC1705017CE_05.xml[11/11/2018 5:08:45 PM]
5 Service Fixture & Tools
5.1 Service Fixture and Tools
The following Service Fixture and Tools are used for Checking & Servicing for this unit.
5.2 Clean Box

10,000 (Federal Standard 209D).
[NOTE]


file:///C|/U...al/Temp/Rar$EXa0.719/viewing/SGML_VIEW_DATA/ALL/H-E08018PP/SVC/DSC1705017CE/doc/DSC1705017CE_06.xml[11/11/2018 5:09:11 PM]
6 Disassembly and Assembly Instructions
6.1 Outline

Important:
1. It is recommended dealing with Clean Box, to keep maintaining the dustproof environment.
(Refef to "5.2. Clean Box " section of this Service Manual for details.)
2. To minimize the possibilities/risk of getting the dust/dirt on the lens surface, keep covering the lens unit with lens caps (front & rear), other
than necessary cases.
3. 
4. Blow off the dust on the surface of the lens with a blower brush.
5. Use lens cleaning KIT (BK)(VFK1900BK).
NOTE:
1. 
following.
Caution
Keep covering the lens unit with Lens caps (front & rear), other than necessary
cases.
6.2 Disassembly Flow Chart
6.3 Disassembly Procedure
Important:


file:///C|/U...al/Temp/Rar$EXa0.719/viewing/SGML_VIEW_DATA/ALL/H-E08018PP/SVC/DSC1705017CE/doc/DSC1705017CE_06.xml[11/11/2018 5:09:11 PM]

Less than class 10,000(Federal Standard 209D))
6.3.1 Removal of the Decoring Plate
1. The Decoring Plate is sticked on the Filter Ring.
2. Put the sheet so that the lens glass is fullty covered.
3. 
6.3.2 Removal of the Shading Frame
1. Remove 2 screws (A) and the Shading Frame.
6.3.3 Removal of the L Mount Unit
1. Remove screw (B) and 3 screws (C).
2. Remove the L Mount Unit.

file:///C|/U...al/Temp/Rar$EXa0.719/viewing/SGML_VIEW_DATA/ALL/H-E08018PP/SVC/DSC1705017CE/doc/DSC1705017CE_06.xml[11/11/2018 5:09:11 PM]
6.3.4 Removal of the Dustproof Rubber and the Rear Frame Unit
1. Remove the Dustproof Rubber.
2. Disconnect the Connector of the Lens P.C.B..
3. Remove 3 screws (D) and the Rear Frame Unit.
6.3.5 Removal of the Lens P.C.B. Unit and the Mount Contact Unit
1. Disconnect the 2 Connectors of the Lens P.C.B..

file:///C|/U...al/Temp/Rar$EXa0.719/viewing/SGML_VIEW_DATA/ALL/H-E08018PP/SVC/DSC1705017CE/doc/DSC1705017CE_06.xml[11/11/2018 5:09:11 PM]
2. Remove 2 screws (E) and the Lens P.C.B. with the Mount Contact Unit.
3. Remove the Mount Connect Unit from Lens P.C.B..
6.3.6 Removal of the Zoom Drive Pin and the Zoom Ring Unit
1. Remove 2 screws (F) and the Zoom Drive Pin.
2. Remove the Zoom Ring Unit.

file:///C|/U...al/Temp/Rar$EXa0.719/viewing/SGML_VIEW_DATA/ALL/H-E08018PP/SVC/DSC1705017CE/doc/DSC1705017CE_06.xml[11/11/2018 5:09:11 PM]
6.4 Assembly Flow Chart
6.5 Assembly procedure
Important:
1. 

file:///C|/U...al/Temp/Rar$EXa0.719/viewing/SGML_VIEW_DATA/ALL/H-E08018PP/SVC/DSC1705017CE/doc/DSC1705017CE_06.xml[11/11/2018 5:09:11 PM]
6.5.1 Installation of the Zoom Ring Unit and the Zoom Drive Pin
1. Install the Zoom Ring Unit and the Zoom Drive Pin.
2. 
6.5.2 Installation of the Mount Contact Unit and the Lens P.C.B.
1. Connect FPC of the Mount Connect Unit to connector.
2. Installation the Main P.C.B. with the Mount Contact Unit.
3. 

file:///C|/U...al/Temp/Rar$EXa0.719/viewing/SGML_VIEW_DATA/ALL/H-E08018PP/SVC/DSC1705017CE/doc/DSC1705017CE_06.xml[11/11/2018 5:09:11 PM]
4. Connect FPCs to 2 connectors of the Lens P.C.B. Unit.
6.5.3 Installation of the Rear Frame Unit and the Dustproof Rubber
1. Install the Rear Frame Unit and the Dustproof Rubber.
2. 
3. Connect FPC to connector of the Lens P.C.B. Unit.

file:///C|/U...al/Temp/Rar$EXa0.719/viewing/SGML_VIEW_DATA/ALL/H-E08018PP/SVC/DSC1705017CE/doc/DSC1705017CE_06.xml[11/11/2018 5:09:11 PM]
6.5.4 Installation of the L Mount Unit
1. Install the L Mount Unit.
2. 
6.5.5 Installation of the Shading Frame
1. Install the Shading Frame.
2. 

file:///C|/U...al/Temp/Rar$EXa0.719/viewing/SGML_VIEW_DATA/ALL/H-E08018PP/SVC/DSC1705017CE/doc/DSC1705017CE_06.xml[11/11/2018 5:09:11 PM]
6.5.6 Installation of the Decoring Plate
1. Insert the 3 holls of the Decoring Unit to the pins of the Filter Ring.
Use new one, do not use the one which is removed.
Double-stick tape sticks to the Decoring Unit of the repair part. Remove the old double-stick tape from the Filter Ring.
2. After installing the Decoring Plate, use a soft cloth to press it into place.

file:///C|/U...al/Temp/Rar$EXa0.719/viewing/SGML_VIEW_DATA/ALL/H-E08018PP/SVC/DSC1705017CE/doc/DSC1705017CE_07.xml[11/11/2018 5:09:35 PM]
7 Maintenance
7.1 Dust / Dirt on the outer casing part(s)
1. 
2. Wipe up the outer casing part with the dry fuzz-free cloth.
7.2 Dust / Dirt on the Lens Glasses (Lens Cleaning)
1. Blow off the dust on the Lens glass surface with the Blower, gently. (Do not blow strongly.)
2. Wipe out the dirt on the Lens glass surface with Lens Cleaning Kit (VFK1900BK) if necessary.
(Consult the instruction sheet which is included in the Lens Cleaning Kit in details.)