Panasonic ET-D3LEW10C User manual

Commercial Use
Model No. ET-D3LEW10C
ET-D3LET30C
ET-D3LET40C
DPQX1301ZC/X1
Zoom Lens
Operating Instructions
ENGLISH
Thank you for purchasing this Panasonic product.
■To ensure correct use of this lens, please read the operating instructions supplied
with the lens and the projector carefully.
■Before using this product, be sure to read “Read this rst!” (Page 3).
■Please save this manual for future use.
ET-D3LEW10C
ET-D3LET40C
ET-D3LET30C

2-ENGLISH
Read this rst! ......................................................................................3
Before Use.............................................................................................4
Preparation............................................................................................5
Before replacing the projection lens........................................................ 5
Attaching and Detaching the Lens .......................................................... 5
Peripheral focus adjustment function (ET-D3LEW10C) .......................... 6
Lens calibration ....................................................................................... 7
Projection relationships.......................................................................8
Lens shift ranges..................................................................................9
Specications .....................................................................................10
Dimensions .........................................................................................10
P rojected image size and Projection distance....... 附表 / Appendix 1
█ Contents

ENGLISH-3
Read this rst! Always follow these precautions
WARNING:
Do not look at or place your skin into the light emitted from the lens while the
projector is being used.
Doing so can cause burns or loss of sight.
zStrong light is emitted from the projector’s lens. Do not look at or place your hands
directly into this light.
zTurn off the power when moving away from the projection lens or projector.
Do not project an image with the lens cover attached.
zDoing so can cause re.
CAUTION:
Before replacing the projection lens, be sure to turn off the power and
disconnect the power plug from the wall outlet.
zUnexpected projection of light may cause injury to eyes.
zReplacing the projection lens without removing the power plug may result in electric
shock.
Do not stand in front of the lens while the projector is being used.
Doing so can cause damage and burns to clothing.
zStrong light is emitted from the projector’s lens.
Do not place objects in front of the lens while the projector is being used.
Doing so can cause re, damage to the object, or malfunction of the lens and
projector.
zStrong light is emitted from the projector’s lens.
Do not open the desiccant bag. Do not eat the contents.
Inadvertently ingesting desiccant could be harmful.
zIf the desiccant gets into your eyes or mouth, immediately rinse with plenty of water
and seek medical attention.
zKeep desiccant out of the reach of children.

4-ENGLISH
This zoom lens is a projection lens equipped with an EEPROM*1 and stepping motor.
*1 EEPROM: Electrically erasable programmable read-only memory
■Supported projectors
PT-SRQ32KC / PT-SRZ31KC / PT-SRS30KC / PT-SRQ22KC / PT-SRZ21KC /
PT-SRS20KC
Note
zModels other than the above may also be supported. Refer to the operating instructions of
the projector you are using.
zIf the projector you are using is the PT-SRQ32KC / PT-SRZ31KC / PT-SRS30KC /
PT-SRZ21KC / PT-SRS20KC, the following versions are not supported.
- PT-SRQ32KC / PT-SRZ31KC / PT-SRS30KC: Earlier than 3.00
- PT-SRZ21KC / PT-SRS20KC: Earlier than 2.00
For details, contact your dealer.
zThe main version of the rmware can be checked in the [STATUS] screen.
■Supplied Accessories
Make sure that the following has been provided.
Part name Appearance
Lens cover
1 each for front and rear
zThe product is delivered
with a lens cover attached.
zThe shape and size of the
lens caps are different for
each product.
Before Use

ENGLISH-5
Preparation
Before replacing the projection lens
Return the projection lens to the home position before replacing or removing it.
For details on how to return the lens to the home position, refer to the operating instructions
of the projector.
Attention
zMake sure that the projector power supply is switched off before attaching or detaching the
projection lens.
zAfter removing the projection lens, store it safely away from vibration or impacts.
z Do not touch the electrical contacts of the projection lens with your ngers. Dust and dirt on
the contacts may cause contact malfunctions, while static electricity may damage the unit.
zDo not touch the surface of the lens with bare hands. Finger prints and dirt on the surface
of the lens will be magnied by the lens and lower the quality of the projected image. Place
the supplied lens cover on the zoom lens when the projector is not in use.
zThe lens is made of glass. The lens could be damaged if brought into contact with or
rubbed against hard objects. Handle the lens carefully.
zUse a clean, soft and dry cloth to wipe away dust and dirt from the projection lens.
Do not use uffy cloths containing oil, water or dust for cleaning. The lens is easily
damaged, so do not apply excessive pressure when wiping it.
Attaching and Detaching the Lens
For details on attaching and detaching the projection lens, refer to the operating instructions
of the projector.

6-ENGLISH
Preparation (continued)
Peripheral focus adjustment function (ET-D3LEW10C)
When yo u change the size of the projected image, the focal balance between the center
and peripheral areas of the screen may shift. This shift in balance tends to increase
proportionally with smaller throw ratios.
The ET-D3LEW10C is equipped with a peripheral focus adjustment function to correct
the shift
in focal balance between the center and peripheral areas of the screen.
1) Operate the projector to align
the focus of the center of the
projected image.
2) Loosen the lock knob by
turning it counterclockwise.
Note
zThe screen sizes displayed on the lens are approximate guides.
3) Turn the peripheral focus
adjustment ring in the
directions of the arrows
to align the focus of the
peripheral areas of the image.
4) Tighten the lock knob by
turning it clockwise.
The illustrations in this procedure depict
use of the PT-SRZ21KC as an example.
■Adjusting the focus
ロックつまみ
周辺フォーカス調整リング
Peripheral focus adjustment ring
Lock knob

ENGLISH-7
Preparation (continued)
Lens calibration
Perform lens calibration after attaching the lens.
The illustrations in this procedure depict
use of the ET-D3LEW10C as an example.
1) Press the < 菜单 > button.
2) Use the ▲ and ▼ buttons to
select [PROJECTOR SETUP],
and press the < 执行 > button.
zThe [PROJECTOR SETUP] screen
appears.
3) Use the ▲ and ▼ buttons to
select [LENS], and press the
<执行 > button.
zThe [LENS] screen appears.
4) Use the ▲ and ▼ buttons to
select [LENS CALIBRATION],
and press the < 执行 > button.
zThe [LENS CALIBRATION] screen
appears.
5) Use the ▲ and ▼ buttons to
select [SHIFT/FOCUS/ZOOM],
and press the < 执行 > button.
zThe conrmation screen appears.
6) Use the and buttons to
select [OK], and press the < 执
行> button.
zLens calibration starts.
zThe projection lens moves to the
home position after adjustment range
calibration is complete.
1/2
PROJECTOR SETUP
PROJECTOR ID ALL
PROJECTION METHOD
LENS
OPERATION SETTING NORMAL
LIGHT OUTPUT 100.0%
BRIGHTNESS CONTROL AUTO
STANDBY MODE NORMAL
NO SIGNAL SHUT-OFF DISABLE
NO SIGNAL LIGHTS-OUT DISABLE
INITIAL STARTUP LAST MEMORY
STARTUP INPUT SELECT LAST USED
DATE AND TIME
SUB MENU
MENU SELECT
执行
SUB MENU
MENU SELECT
LENS
LENS TYPE ET-D3LEW10C
LENS INFORMATION SETTING
LENS MEMORY
LENS HOME POSITION
ACTIVE FOCUS OPTIMIZER
LENS CALIBRATION
执行
EXECUTE
MENU SELECT
LENS CALIBRATION : ET-D3LEW10C
SHIFT/FOCUS/ZOOM
SHIFT/FOCUS
ZOOM
执行
LENS CALIBRATION : ET-D3LEW10C
OK
Proceed LENS CALIBRATION,
and return to HOME POSITION.
EXECUTE
CHANGE
CANCEL
执行
Note
zIf lens calibration is not performed, the available zoom range will be narrowed.

8-ENGLISH
Projection relationships
The dimensional relationship between the screen and the projector is shown below.
■Dimensional relationship diagram
Note
zThis diagram assumes that the size and position of the projected image will be adjusted so
that the image lls the entire screen.
zThis illustration is not drawn to scale.
L Projection distance
LW Minimum distance
LT Maximum distance
L1 Lens protrusion dimension
SH Projected image height
SW Projected image width
SD Projected image size
zDimension for L1 (approximate values) (Unit: m)
Projector model Dimension for L1 (approximate value)
ET-D3LEW10C ET-D3LET30C ET-D3LET40C
PT-SRQ32KC / PT-SRZ31KC / PT-SRS30KC 0.18 0.15 0.10
PT-SRQ22KC / PT-SRZ21KC / PT-SRS20KC 0.21 0.18 0.13
Note
zThe illustrations of projectors in this manual are for informational purposes only and do not
represent a specic projector model. Congurations may vary with the model.
Attention
zTo prevent obstruction of the intake and exhaust vents, install the projector with a
clearance at least 500 mm (1 ft. 7 in.) from walls and objects.
If you are installing the projector in a sealed space, be sure to provide additional air
conditioning equipment and ventilation equipment. Insufcient ventilation will result in an
accumulation of heat and may activate the projector's protection circuit.
zAvoid setting up in places which are subject to sudden temperature changes, such as near
an air conditioner or lighting equipment (studio lamps, etc.).
■Dimensional relationship
For details on the projection distance (L), refer to “Projected image size and Projection
distance” and “Projection distance formulas” in the Appendix.
SD
L (LW/LT)
L1
L1
L (LW/LT)
SW SH
SH
SW
投写画面
スクリーン
スクリーン
Projected image
Screen
Screen

ENGLISH-9
Lens shift ranges
After moving the lens to the home position according to “Lens calibration” on page 7,
you can use the position of the projected image at that position (i.e., the standard
projection position) as a basis, and use the lens shift adjustment function on the projector
to adjust the position of the projected image within the respective lens shift ranges.
Perform lens shift adjustment within the ranges shown in the following illustrations.
Moving the lens outside of the adjustment ranges may alter the focus. This occurs due
to limitations in lens movement that are intended to protect the optical components.
The following illustrations depict lens shift ranges for oor installations of the projector.
PT-SRQ32KC / PT-SRQ22KC
PT-SRZ31KC / PT-SRZ21KC
PT-SRS30KC / PT-SRS20KC
Note
zThe home position of the projector a point of origin position for the lens shift (i.e., vertical and
horizontal positions of the lens) based on the results of lens calibration. It is not the optical
center position of the screen.
0.29H0.29H
0.15V0.15V
0.59V
0.59V
Projected image
width H
Projected image height V
Standard projection position
0.2H
0.2H
0.12V0.12V
0.55V
0.55V
Projected image
width H
Projected image height V
Standard projection position
0.3H
0.3H
0.1V0.1V
0.5V
0.5V
Projected image
width H
Projected image height V
Standard projection position

10-ENGLISH
Dimensions
Specications
(Unit: mm)
Model number Dimensions
ET-D3LEW10C
Ø 154 (6-1/16")
Ø 130 (5-1/8")
354 (13-15/16")
ET-D3LET30C
Ø 130 (5-1/8")
Ø 154 (6-1/16")
322 (12-11/16")
Check the specications of each projection lens, and use the appropriate lens for your
intended use.
Model No. ET-D3LEW10C ET-D3LET30C ET-D3LET40C
F value 2.5 2.5 2.5
Focal Length (f) 26.6 mm (1-1/16") -
36.4 mm (1-7/16")
50.4 mm (1-31/32") -
98.0 mm (3-27/32")
96.6 mm (3-13/16") -
154.9 mm (6-3/32")
Dimensions*1
Width 154 mm (6-1/16") 154 mm (6-1/16") 154 mm (6-1/16")
Height 154 mm (6-1/16") 154 mm (6-1/16") 154 mm (6-1/16")
Depth 354 mm (13-15/16") 322 mm (12-11/16") 279 mm (10-31/32")
Net Weight Approx. 6.2 kg (13.7 lb) Approx. 5.8 kg (12.8 lb) Approx. 5.0 kg (11 lb)
*1: Excluding protrusions.