Panasonic H-FS1442APP User manual

file:///C|/U...emp/Rar$EXa0.829/viewing/SGML_VIEW_DATA/ALL/H-FS1442APP/SVC/DSC1302014CE/doc/DSC1302014CE_cvr.xml[11/12/2018 11:14:52 AM]
Order No.DSC1302014CE
B26
Interchangeable Lens for Digital Camera
Model No. H-FS1442APP
H-FS1442AE
H-FS1442AGK
Colour
(S)...............Silver Type
(K)...............Black Type

file:///C|/U...emp/Rar$EXa0.829/viewing/SGML_VIEW_DATA/ALL/H-FS1442APP/SVC/DSC1302014CE/doc/DSC1302014CE_cvr.xml[11/12/2018 11:14:52 AM]
© Panasonic Corporation 2013 Unauthorized copying and distribution is a violation of law.

file:///C|/U...emp/Rar$EXa0.829/viewing/SGML_VIEW_DATA/ALL/H-FS1442APP/SVC/DSC1302014CE/doc/DSC1302014CE_01.xml[11/12/2018 11:15:49 AM]
1 Service Navigation
1.1 Introduction
This service manual contains technical information, which allow service personnel’s to understand and service this model.
Please place orders using the parts list and not the drawing reference numbers.

1.2 Important Notice
1.2.1 About LENS MAIN UNIT (Ref. 208)
1. 
critical lens adjustments.

2. 
(Ref. 202), to maintain Serial number of owner's original lens.

file:///C|/U...emp/Rar$EXa0.829/viewing/SGML_VIEW_DATA/ALL/H-FS1442APP/SVC/DSC1302014CE/doc/DSC1302014CE_01.xml[11/12/2018 11:15:49 AM]
3. No adjustment is required when replacing the part mentioned on Fig.1-1. But, when tighten the concerned screws,apply proper
torque mentioned on "4. Disassembly and Assembly Instruction" section.

file:///C|/U...emp/Rar$EXa0.829/viewing/SGML_VIEW_DATA/ALL/H-FS1442APP/SVC/DSC1302014CE/doc/DSC1302014CE_02.xml[11/12/2018 11:16:56 AM]
2 Operating Guide
2.1 Before Use
(Information for Your Safety)
2.2 Cautions For Use

file:///C|/U...emp/Rar$EXa0.829/viewing/SGML_VIEW_DATA/ALL/H-FS1442APP/SVC/DSC1302014CE/doc/DSC1302014CE_02.xml[11/12/2018 11:16:56 AM]
2.3 Components
2.3.1 Accessories
2.3.2 Attaching/Detaching the Lens

file:///C|/U...emp/Rar$EXa0.829/viewing/SGML_VIEW_DATA/ALL/H-FS1442APP/SVC/DSC1302014CE/doc/DSC1302014CE_02.xml[11/12/2018 11:16:56 AM]

file:///C|/U...emp/Rar$EXa0.829/viewing/SGML_VIEW_DATA/ALL/H-FS1442APP/SVC/DSC1302014CE/doc/DSC1302014CE_03.xml[11/12/2018 11:17:41 AM]
3 Service Fixture and Tools
3.1 Service Fixture and Tools
The following Service Fixture and Tools are used for Checking & Servicing for this unit.
3.2 Clean Box

10,000 (Federal Standard 209D).
(When cleaning the inside of a lens, it is indispensable.)
[NOTE]

when cleaning the inside of a lens.

file:///C|/U...emp/Rar$EXa0.829/viewing/SGML_VIEW_DATA/ALL/H-FS1442APP/SVC/DSC1302014CE/doc/DSC1302014CE_04.xml[11/12/2018 11:18:42 AM]
4 Disassembly and Assembly Procedure
4.1 Outline
It is recommended dealing with clean box, to keep maintaining the dustproof environment.
(Refer to“3.2. Clean Box”section of this service manual for details.)
Important:
1. 

As for procedure, refer to the “5 Maintenance” for details.
2. To minimize the possibilities/risk of getting the dust/dirt on the lens surface, keep covering the lens unit with lens caps (front &
rear), other than necessary cases.
3. 
4. Blow off the dust on the surface of the lens with a blower brush.
5. Use lens cleaning KIT (BK)(VFK1900BK).
Proceed disassemble/assemble, by referring the following table and Fig. W1.
NOTE:
1. 
on the following table.
2. Use VFK1390 (small driver) when screwing Ref. B213.
Interchangeable Lens (H-FS1442A)

file:///C|/U...emp/Rar$EXa0.829/viewing/SGML_VIEW_DATA/ALL/H-FS1442APP/SVC/DSC1302014CE/doc/DSC1302014CE_04.xml[11/12/2018 11:18:42 AM]
4.2 Disassembly procedure
Important:


4.2.1 Removal of the Decoration Ring
1. Decoration ring is sticked on the 1st lens frame unit.
2. Put the sheet so that the lens glass is fully covered.
3. 

file:///C|/U...emp/Rar$EXa0.829/viewing/SGML_VIEW_DATA/ALL/H-FS1442APP/SVC/DSC1302014CE/doc/DSC1302014CE_04.xml[11/12/2018 11:18:42 AM]
4.2.2 Removal of the 1st lens frame unit
1. Remove the 3 screws (A).
4.2.3 Removal of the Shading frame
1. Remove the 3 screws (B).

file:///C|/U...emp/Rar$EXa0.829/viewing/SGML_VIEW_DATA/ALL/H-FS1442APP/SVC/DSC1302014CE/doc/DSC1302014CE_04.xml[11/12/2018 11:18:42 AM]
4.2.4 Removal of the L mount unit
1. Remove 1 screw (C) and 3 screws (D).
2. Insert 3 adjustment shafts(VMS7941 or an equivalent one) to screw holes in order not to remove Back adjust-ment washers.Then,
remove the L mount unit.

file:///C|/U...emp/Rar$EXa0.829/viewing/SGML_VIEW_DATA/ALL/H-FS1442APP/SVC/DSC1302014CE/doc/DSC1302014CE_04.xml[11/12/2018 11:18:42 AM]
4.2.5 Removal of the Rear frame unit
1. Remove 4 screws (E).
4.2.6 Removal of the Lens P.C.B.unit and the Lens mount contact unit
1. Disconnect 4 connectors.
4.2.7 Removal of the Lens mount contact unit

file:///C|/U...emp/Rar$EXa0.829/viewing/SGML_VIEW_DATA/ALL/H-FS1442APP/SVC/DSC1302014CE/doc/DSC1302014CE_04.xml[11/12/2018 11:18:42 AM]
1. Disconnect 1 connector.
4.3 Assembly procedure
Important:

4.3.1 Installation of the 1st lens frame unit
1. 
(Torque Driver : RFKZ0456)
(Torque : 8 ± 0.5N cm)
4.3.2 Installation of the Decoration ring
1. Please insert the pins of the Decoration ring to the hole of the Lens top unit
Use new one, do not use the one which is removed.
Double-stick tape sticks to the Decoration ring of therepair part.
Please remove the old double-stick tape from the Lenstop unit.
2. After installing the Decoration ring, use a soft cloth to press it into place.

file:///C|/U...emp/Rar$EXa0.829/viewing/SGML_VIEW_DATA/ALL/H-FS1442APP/SVC/DSC1302014CE/doc/DSC1302014CE_04.xml[11/12/2018 11:18:42 AM]
4.3.3 Installation of the Lens mount contact unit
1. Connect 1 connector.
4.3.4 Installation of the Lens P.C.B.unit and the Lens mount contact unit
1. Connect 4 connectors.

file:///C|/U...emp/Rar$EXa0.829/viewing/SGML_VIEW_DATA/ALL/H-FS1442APP/SVC/DSC1302014CE/doc/DSC1302014CE_04.xml[11/12/2018 11:18:42 AM]
4.3.5 Installationl of the Rear frame unit
1. 
(Torque Driver : RFKZ0456)
(Torque : 8 ± 0.5N cm)
4.3.6 Installation of the L mount unit
1. Install the L mount unit.
Then, remove 3 adjustment shafts(VMS7941 or an equivalent one).

file:///C|/U...emp/Rar$EXa0.829/viewing/SGML_VIEW_DATA/ALL/H-FS1442APP/SVC/DSC1302014CE/doc/DSC1302014CE_04.xml[11/12/2018 11:18:42 AM]
2. 
(Torque Driver : RFKZ0456)
(Torque for screw (D) : 16±0.5N cm)
4.3.7 Installation of the Shading frame
1. 
(Torque Driver : RFKZ0456)
(Torque for screw (B) : 7.5±0.5N cm)

file:///C|/U...emp/Rar$EXa0.829/viewing/SGML_VIEW_DATA/ALL/H-FS1442APP/SVC/DSC1302014CE/doc/DSC1302014CE_04.xml[11/12/2018 11:18:42 AM]

file:///C|/U...emp/Rar$EXa0.829/viewing/SGML_VIEW_DATA/ALL/H-FS1442APP/SVC/DSC1302014CE/doc/DSC1302014CE_05.xml[11/12/2018 11:19:47 AM]
5 Maintenance
5.1 Lens Cleaning
5.1.1 Dust / Dirt on the outer casing part(s)
1. 
2. Wipe up the Outer casing part with the dry fuzz-free cloth.
5.1.2 Dust / Dirt on the Lens Glasses.

1. When it is outside surface of the lens
When the dust and / or dirt gets on the outer side surface of the Lens glasses, order the following procedures.
1. Blow off the dust on the Lens glass surface with the Blower, gently. (Do not Blow too strongly.)
2. Wipe out the dirt on the lens glass surface with Lens cleaning KIT (VFK1900BK) if necessary.
(Consult the Instruction sheet which is included in the Lens cleaning KIT in details.)
2. When it is inside of the lens
When there is dust / dirt inside surface of the 1st lens frame unit and 8th lens, remove it by referring to the following procedures.

file:///C|/U...emp/Rar$EXa0.829/viewing/SGML_VIEW_DATA/ALL/H-FS1442APP/SVC/DSC1302014CE/doc/DSC1302014CE_05.xml[11/12/2018 11:19:47 AM]
1. 
(Less than class 10,000 (Federal Standard 209D))
As for clean box, refer to the "3.2. Clean Box", in details.
2. 
3. To keep the Lens performance, can only use the original 1st lens frame unit and 8th lens.
So the 1st lens frame unit and 8th lens is not supplied as spare parts.
Also do not exchange the 1st lens frame unit and 8th lens taking from others.
4. When clean inside 8th lens, blow out dust by gas duster at Tele side.
(Refer to the following picture.)