Panasonic Lumix DMC-GH1KPP User manual

© Panasonic Corporation 2009. Unauthorized copy-
ing and distribution is a violation of law.
ORDER NO. DSC0905029CE
B26
Digital Camera/Lens Kit
Model No.DMC-GH1KPP
DMC-GH1KEB
DMC-GH1KEC
DMC-GH1KEG
DMC-GH1KGC
DMC-GH1KGH
DMC-GH1KGK
DMC-GH1KGN
DMC-GH1KGT
Colour
(K)...........Black Type
(N)...........Gold Type (only PP/EC/EG/GC)
(R)...........Red Type (only PP/EB/EC/EG/GC)

2
TABLE OF CONTENTS
PAGE PAGE
1 Safety Precaution -------------------------------------------------3
1.1. General Guidelines ----------------------------------------3
1.2. Leakage Current Cold Check ---------------------------3
1.3. Leakage Current Hot Check (See Figure 1.)--------3
1.4. How to Discharge the Capacitor on Flash Sub
PCB------------------------------------------------------------4
2Warning--------------------------------------------------------------5
2.1. Prevention of Electrostatic Discharge (ESD)
to Electrostatically Sensitive (ES) Devices ----------5
2.2. How to Recycle the Lithium Ion Battery (U.S.
Only)-----------------------------------------------------------5
2.3. Caution for AC Cord(For EB/GC/GH) -----------------6
2.4. How to Replace the Lithium Battery-------------------7
3ServiceNavigation------------------------------------------------8
3.1. Introduction --------------------------------------------------8
3.2. Important Notice --------------------------------------------8
3.3. General Description About Lead Free Solder
(PbF) -------------------------------------------------------- 11
3.4. How to Define the Model Suffix (NTSC or PAL
model)------------------------------------------------------- 12
4Specifications---------------------------------------------------- 15
5LocationofControlsandComponents------------------ 16
6ServiceMode----------------------------------------------------- 32
6.1. Error Code Memory Function ------------------------- 32
7TroubleshootingGuide---------------------------------------- 34
8 Service Fixture & Tools --------------------------------------- 38
8.1. Service Fixture and Tools ------------------------------ 38
8.2. Clean Box -------------------------------------------------- 39
8.3. Service Position ------------------------------------------ 40
9DisassemblyandAssemblyInstructions--------------- 41
9.1. Disassembly Flow Chart-------------------------------- 41
9.2. PCB Location---------------------------------------------- 41
9.3. Disassembly Procedure -------------------------------- 42
9.4. Disassembly and Assemble Procedure for the
Lens --------------------------------------------------------- 53
10 Measurements and Adjustments -------------------------- 55
10.1. Matrix Chart for Replaced Part and Necessary
Adjustment------------------------------------------------- 55
11 Maintenace -------------------------------------------------------- 57
11.1. Notice in external cleaning----------------------------- 57
11.2. General description (Lens cleaning) ---------------- 58
11.3. Method of cleaning inside of lens (H-
VS014140: Included in DMC-GH1K)---------------- 59

3
1SafetyPrecaution
1.1. General Guidelines
1. IMPORTANT SAFETY NOTICE
There are special components used in this equipment
which are important for safety. These parts are marked by
in the Schematic Diagrams, Circuit Board Layout,
Exploded Views and Replacement Parts List. It is essen-
tial that these critical parts should be replaced with manu-
facturer’s specified parts to prevent X-RADIATION,
shock, fire, or other hazards. Do not modify the original
design without permission of manufacturer.
2. An Isolation Transformer should always be used during
the servicing of AC Adaptor whose chassis is not isolated
from the AC power line. Use a transformer of adequate
power rating as this protects the technician from acci-
dents resulting in personal injury from electrical shocks. It
will also protect AC Adaptor from being damaged by acci-
dental shorting that may occur during servicing.
3. When servicing, observe the original lead dress. If a short
circuit is found, replace all parts which have been over-
heated or damaged by the short circuit.
4. After servicing, see to it that all the protective devices
such as insulation barriers, insulation papers shields are
properly installed.
5. After servicing, make the following leakage current
checks to prevent the customer from being exposed to
shock hazards.
1.2. Leakage Current Cold Check
1. Unplug the AC cord and connect a jumper between the
two prongs on the plug.
2. Measure the resistance value, with an ohmmeter,
between the jumpered AC plug and each exposed metal-
lic cabinet part on the equipment such as screwheads,
connectors, control shafts, etc. When the exposed metal-
lic part has a return path to the chassis, the reading
should be between 1 Mand 5.2 M. When the exposed
metal does not have a return path to the chassis, the
reading must be infinity.
1.3. Leakage Current Hot Check
(See Figure 1.)
1. Plug the AC cord directly into the AC outlet. Do not use
an isolation transformer for this check.
2. Connect a 1.5 k, 10 W resistor, in parallel with a 0.15 F
capacitor, between each exposed metallic part on the set
and a good earth ground, as shown in Figure 1.
3. Use an AC voltmeter, with 1 k/V or more sensitivity, to
measure the potential across the resistor.
4. Check each exposed metallic part, and measure the volt-
age at each point.
5. Reverse the AC plug in the AC outlet and repeat each of
the above measurements.
6. The potential at any point should not exceed 0.75 V RMS.
A leakage current tester (Simpson Model 229 or equiva-
lent) may be used to make the hot checks, leakage cur-
rent must not exceed 1/2 mA. In case a measurement is
outside of the limits specified, there is a possibility of a
shock hazard, and the equipment should be repaired and
rechecked before it is returned to the customer.
Figure. 1

4
1.4. How to Discharge the Capacitor on Flash Sub PCB
CAUTION:
1. Be sure to discharge the capacitor on FLASH SUB PCB.
2. Be careful of the high voltage circuit on FLASH SUB PCB when servicing.
[Discharging Procedure]
1. Refer to the disassemble procedure and remove the necessary parts/unit.
2. Put the insulation tube onto the lead part of Resistor (ERG5SJ102:1k/5W).
(An equivalent type of resistor may be used.)
3. Put the resistor between both terminals of capacitor on FLASH SUB PCB for approx. 5 seconds.
4. After discharging confirm that the capacitor voltage is lower than 10V using a voltmeter.
Fig. F1

5
2Warning
2.1. Prevention of Electrostatic Discharge (ESD) to Electrostatically
Sensitive (ES) Devices
Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called Elec-
trostatically Sensitive (ES) Devices.
The following techniques should be used to help reduce the incidence of component damage caused by electrostatic discharge
(ESD).
1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any ESD on your
body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging ESD wrist strap,
which should be removed for potential shock reasons prior to applying power to the unit under test.
2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as alumi-
num foil, to prevent electrostatic charge buildup or exposure of the assembly.
3. Use only a grounded-tip soldering iron to solder or unsolder ES devices.
4. Use only an antistatic solder removal device. Some solder removal devices not classified as "antistatic (ESD protected)" can
generate electrical charge sufficient to damage ES devices.
5. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ES devices.
6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most
replacement ES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or compara-
ble conductive material).
7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material
to the chassis or circuit assembly into which the device will be installed.
CAUTION :
Be sure no power is applied to the chassis or circuit, and observe all other safety precautions.
8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise harmless motion such as the
brushing together of your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity (ESD) suf-
ficient to damage an ES device).
2.2. How to Recycle the Lithium Ion Battery (U.S. Only)

6
2.3. Caution for AC Cord
(For EB/GC/GH)
2.3.1. Information for Your Safety
IMPORTANT
Your attention is drawn to the fact that recordin g of pre-
recorded tapes or discs or other published or broadcast
material may infringe copyright laws.
WARNING
To redu c e t he ri s k of fir e o r s hock h a zard , d o not exp o se
this equipment to rain or moisture.
CAUTION
To redu c e the ris k o f f ire or sh o c k haza r d a nd ann o yin g
interference, use the recommended accessories only.
FOR YOUR SAFETY
DO NOT REMOVE THE OUTER COVER
To prevent electric shock, do not remove the cover. No user
serviceable parts inside. Refer servicing to qualified service
personnel.
2.3.2. Caution for AC Mains Lead
For your safety, please read the following text carefully.
This appliance is supplied with a moulded three-pin mains plug
for your safety and convenience.
A 5-ampere fuse is fitted in this plug.
Should the fuse need to be replaced please ensure that the
replacement fuse has a rating of 5 amperes and it is approved
by ASTA or BSI to BS1362
Check for the ASTA mark or the BSI mark on the body of the
fuse.
If the plug contains a removable fuse cover you must ensure
that it is refitted when the fuse is replaced.
If you lose the fuse cover, the plug must not be used until a
replacement cover is obtained.
A replacement fuse cover can be purchased from your local
Panasonic Dealer.
If the fitted moulded plug is unsuitable for the socket outlet in
your home then the fuse should be removed and the plug cut
off and disposed of safety.
There is a danger of severe electrical shock if the cut off plug is
inserted into any 13-ampere socket.
If a new plug is to be fitted please observe the wiring code as
shown below.
If in any doubt, please consult a qualified electrician.
2.3.2.1. Important
The wires in this mains lead are coloured in accordance with
the following code:
As the colours of the wires in the mains lead of this appliance
may not correspond with the coloured markings identifying the
terminals in your plug, proceed as follows:
The wire which is coloured BLUE must be connected to the ter-
minal in the plug which is marked with the letter N or coloured
BLACK.
The wire which is coloured BROWN must be connected to the
terminal in the plug which is marked with the letter L or coloured
RED.
Under no circumstances should either of these wires be con-
nected to the earth terminal of the three pin plug, marked with
the letter E or the Earth Symbol.
2.3.2.2. Before Use
Remove the Connector Cover as follows.
2.3.2.3. How to Replace the Fuse
1. Remove the Fuse Cover with a screwdriver.
2. Replace the fuse and attach the Fuse cover.
Blue Neutral
Brown Live

7
2.4. How to Replace the Lithium Battery
2.4.1. Replacement Procedure
1. Remove the AUDIO PCB. (Refer to Disassembly Procedures.)
2. Remove the Lithium battery (Ref. No. “B4001” at foil side of AUDIO PCB) and then replace it into new one.
NOTE:
This Lithium battery is a critical component.
(Type No.: ML-421S/ZTE Manufactured by Energy Company, Panasonic Corporation.)
It must never be subjected to excessive heat or discharge.
It must therefore only be fitted in requirement designed specifically for its use.
Replacement batteries must be of same type and manufacture.
They must be fitted in the same manner and location as the original battery, with the correct polarity contacts observed.
Do not attempt to re-charge the old battery or re-use it for any other purpose.
It should be disposed of in waste products destined for burial rather than incineration.
NOTE:
Above caution is applicable for a battery pack which is for DMC-GH1K series, as well.

8
3ServiceNavigation
3.1. Introduction
This service manual contains technical information, which allow service personnel’s to understand and service this model.
Please place orders using the parts list and not the drawing reference numbers.
If the circuit is changed or modified, the information will be followed by service manual to be controlled with original service manual.
3.2. Important Notice
*When servicing, it is recommended dealing with Clean box. (Refer to "8.2. Clean Box" section of this service manual for details.)
3.2.1. Camera Body Unit
3.2.1.1. About Mount Box Block (Ref. 7)
1. This Service Manual does not contain the repair service information for "MOUNT BOX BLOCK"(Ref.7), because it requires
special facilities and equipment.
a. Schematic diagram, Block diagram and P. C . B . l a y o u t o f " M O U N T B O X B L O C K " .
b. Parts list for individual parts of "MOUNT BOX BLOCK"
2. If the "MOUNT BOX BLOCK" is confirmed as defective, exchange the "MOUNT BOX BLOCK" as a unit (supplied as service
parts size).
3. Before exchange the "MOUNT BOX BLOCK", the performances must be carefully checked, by following the "7.Troubleshoot-
ing Guide" section of this service manual.
Fig. S1

9
Important:
1. After replacing the MOUNT BOX BLOCK, the mount box data has to be stored to the unit.
When the serial number of the mount box block which is put on the shield plate of mount box block is entered to the adjust-
ment unit, the applicable data is stored into the MAIN P.C.B.
For more details, consult the adjustment instruction which is available together with the Maintenance software at "software
download" on the "Support Information from NWBG/VDBG-AVC" web-site in "TSN system".
Fig. S2
2. The full adjustment procedures must be performed after replacing the "MOUNT BOX BLOCK", otherwise picture quality can
not be meet with specification.
3.2.1.2. About Main P.C.B. (Ref. 1) / Audio P.C.B. (Ref. 3)
1. This Service Manual does not contain the repair service information for "MAIN P.C.B."(Ref.1) and “AUDIO P.C.B.”(Ref.3),
because it requires special facilities and equipment.
a. Schematic diagram, Block diagram and P.C.B. layout of "MAIN P.C.B." / “AUDIO P.C.B.”.
b. Parts list for individual parts of "MAIN P.C.B." / “AUDIO P.C.B.”.
2. When a part replacement is required for repairing "MAIN P.C.B." and “AUDIO P.C.B.”, replace as an assembled P.C.B. parts
and send it/them to Central Repair Center.
3. The following category is recycle module part. Please send it/them to Central Repair Center.
*MAIN P.C.B. (VEP56084A: DMC-GH1KPP/GC/GH/GK/GN/GT)
*MAIN P.C.B. (VEP56084B: DMC-GH1KEB/EC/EG)
*AUDIO P.C.B. (VEP54012A): Excluding replacement of Lithium Battery
Important (About Main P.C.B.):
1. Before exchange the "MAIN P.C.B.", the performances must be carefully checked, by following the "7.Troubleshooting Guide"
section of this service manual.
2. Before replacing the "MAIN P. C . B . " , p r o c e e d t h e E E P R O M d a t a backup from the unit. After replacing the MAIN PCB, over-
write the EEPROM data with backup data from the unit first, then proceed the adjustment /inspection.
If it is impossible to make a data backup due to the unit does not turns on the power and so on, additional adjustment (using
the light box) is required.
For more details, consult the adjustment instruction which is available together with the Maintenance software at "software
download" on the "Support Information from NWBG/VDBG-AVC" web-site in "TSN system".
3. The full adjustment procedures must be performed after replacing the "MAIN P.C.B.", otherwise Picture quality can not be
meet with specification.

10
3.2.2. Lens Unit
3.2.2.1. About Lens MAIN Block unit (Ref. 215)
1. This Service Manual does not contain the repair service information for "LENS MAIN BLOCK UNIT"(Ref.215), because it
requires special facilities and equipment.
2. "LENS MAIN BLOCK UNIT" performance must be confirmed with the "7.Troubleshooting Guide" section of this service man-
ual.
3. In case of the "LENS MAIN BLOCK UNIT" defect, contact to the service department of sales company.
Fig. S3
3.2.2.2. About Lens Cleaning (Inside of the Lens Unit)
1. When there is a dust/dirt inside surface of the 1st lens frame unit and/or subject side of the 2nd lens frame unit, it can be
cleaned up by removing the "Hood Adaptor" (Ref.202) and 1st lens frame unit.
Refer to the "11.Maintenance" Section of this service Manual, for details.
IMPORTANT:
IT MUST BE PERFORMED INSIDE OF SATISFIED CLEAN LEVEL
(Satisfied clean level: Less than class 10,000 Federal Standard 209D).
As for clean box, refer to the "8.2. Clean box" in details.
3.2.2.3. About Flexible Cable and Connector
Do not touch carelessly so that the foreign body should not adhere to the terminal part of flexible cable and connector.
Wipe off with a clean cloth and the cotton bud, etc. when the terminal part is dirty.

11
3.3. General Description About Lead Free Solder (PbF)
The lead free solder has been used in the mounting process of all electrical components on the printed circuit boards used for this
equipment in considering the globally environmental conservation.
The normal solder is the alloy of tin (Sn) and lead (Pb). On the other hand, the lead free solder is the alloy mainly consists of tin
(Sn), silver (Ag) and Copper (Cu), and the melting point of the lead free solder is higher approx.30C (86F) more than that of the
normal solder.
Distinction of PCB Lead Free Solder being used
Service caution for repair work using Lead Free Solder (PbF)
•Theleadfreesolderhastobeusedwhenrepairingthe equipment for which the lead free solder is used.
(Definition: The letter of “PbF” is printed on the PCB using the lead free solder.)
•Toputleadfreesolder,itshouldbewellmoltenand mixed with the original lead free solder.
•RemovetheremainingleadfreesolderonthePCBcleanlyforsolderingofthenewIC.
• Since the melting point of the lead free solder is higher than that of the normal lead solder, it takes the longer time to melt the
lead free solder.
•Use the soldering iron (more than 70W) equipped with the temperature control after setting the temperature at 350±30C
(662±86F).
Recommended Lead Free Solder (Service Parts Route.)
•Thefollowing3typesofleadfreesolderareavailablethroughtheservicepartsroute.
RFKZ03D01KS-----------(0.3mm 100g Reel)
RFKZ06D01KS-----------(0.6mm 100g Reel)
RFKZ10D01KS-----------(1.0mm 100g Reel)
Note
* Ingredient: tin (Sn) 96.5%, silver (Ag) 3.0%, Copper (Cu) 0.5%, Cobalt (Co) / Germanium (Ge) 0.1 to 0.3%

12
3.4. How to Define the Model Suffix (NTSC or PAL model)
There are six kinds of DMC-GH1K, regardless of the colours.
•a)DMC-GH1K(Japandomesticmodel)
•b)DMC-GH1KPP
•c)DMC-GH1KEB/EC/EG/GH/GN
•d)DMC-GH1KGC
•e)DMC-GH1KGT
•f) DMC-GH1KGK
What is the difference is that the “INITIAL SETTINGS” data which is stored in Flash ROM mounted on MAIN PCB.
3.4.1. Defining methods:
To def i n e the m o d el su ffi x t o be se r vice d , re f e r to th e nameplate which is putted on the bottom side of the Unit.
NOTE:
After replacing the MAIN PCB, be sure to achieve adjustment.
The adjustment instruction is available at “software download” on the “Support Information from NWBG/VDBG-AVC” web-site in
“TSN system”, together with Maintenance software.

13
3.4.2. INITIAL SETTINGS:
When you replace the MAIN PCB, be sure to perform the initial settings after achieving the adjustment by ordering the following pro-
cedure in accordance with model suffix of the unit.
1. IMPORTANT NOTICE:
Before proceeding Initial settings, be sure to read the following CAUTIONS.
2. PROCEDURES:
•Preparation
Insert the SD memory card which has a few photo data.
•Step 1. The temporary cancellation of initial setting:
Set the Drive mode lever to [ SINGLE ].
While keep pressing [ DISPLAY ] and [ FILM MODE ] buttons simultaneously, turn the Power on.
•Step 2. The cancellation of initial setting:
Press the [PLAYBACK] button, then playback the picture.
Press [ FILM MODE ] and “[ UP ] of Cursor buttons” simultaneously, then turn the Power off.
•Step 3. Turn the Power on:
Set the mode dial to [ P ], and then turn the Power on.
•Step 4. Display the INITIAL SETTING:
While keep pressing [ MENU/SET ] and “[ RIGHT ] of Cursor buttons” simultaneously, turn the Power off.
When MAIN P.C.B. is replaced, all of the model suffix is displayed as follows.
There are two kinds of “INITIAL SETTINGS” menu format.
[CASE 1. After replacing MAIN P.C.B.]
[Except "EG, EB and EC" models : (VEP56084A is used as a Main P.C.B.)]
When MAIN P.C.B. has just been replaced, all of the model suffix are displayed as follows. (two pages in total)
[Only for "EG, EB and EC" models : (VEP56084B is used as a Main P.C.B.)]
When MAIN P.C.B. has just been replaced, only 4 model suffix are displayed as follows.

14
[CASE 2. Other than "After replacing MAIN P.C.B."]
•Step 5. Set the INITIAL SETTING: (Refer to “CAUTION 1”)
[Caution: After replacing MAIN P.C.B.]
The model suffix can been chosen, JUST ONE TIME.
Once one of the model suffix have been chosen, the model suffix lists will not be displayed, thus, it can be changed.
Select the area carefully.
Select the area with pressing “[ UP ] / [ DOWN ] of Cursor buttons”, and then press the “[ RIGHT ] of Cursor buttons”.
The only set area is displayed, and then press the “[ RIGHT ] of Cursor buttons” after confirmation.
(The unit is powered off automatically.)
Confirm the display of “PLEASE SET THE CLOCK” in English when the unit is turned on again.
•Step 6. CONFIRMATION:
The display shows “PLEASE SET THE CLOCK” when turn the Power on again.
When the unit is connected to PC with USB cable, it is detected as removable media.
1) As for your reference Default setting condition is given in the following table.
•Default setting (After “INITIAL SETTINGS”)
MODEL VIDEO OUTPUT LANGUAGE DATE REMARKS
a) DMC-GH1K (Japan domestic model) NTSC Japanese Year/Month/Date
b) DMC-GH1KPP NTSC English Month/Date/Year
c) DMC-GH1KEB/EC/EG/GC/GH/GN PAL English Date/Month/Year
d) DMC-GH1KGK PAL Chinese (simplified) Year/Month/Date
e) DMC-GH1KGT NTSC Chinese (traditional) Year/Month/Date

15
4Specifications

16
5LocationofControlsandComponents
Names of the Components
Camera body
1Flash
2 Sensor
3 Self-timer indicator
AF assist lamp
4Lensreleasebutton
5 Lens lock pin
6Mount
7Lensfittingmark
8Frontdial
9 [LVF/LCD] button
10 Diopter adjustment dial
11 Viewfinder
12 Eye sensor
13 Playback button
14 [AF/AE LOCK] button
15 Camera ON/OFF switch
16 Motion picture button
17 Eye Cup
18 LCD monitor
19 [DISPLAY] button
20 Delete button/
Preview button
21 [MENU/SET] button
22 Cursor buttons
/ISO
/AF mode
/Function button
Assign Menu to button. It is convenient to register Menu that is used often.
[ASPECT RATIO]/[QUALITY]/[METERING MODE]/[I.EXPOSURE]/[GUIDE LINE]/
[RECAREA]/[REMAININGDISP.]
/WB (White balance)
23
76 5 4
1
8
11 13
18 19
9 10 12 14 15
22
16
17 20 21

17
23 Focus mode dial
24 Flash open lever
25 Stereo microphone
26 Drive mode lever
Single:
Burst:
Auto Bracket:
Self-timer:
27 Shutter button
28 Focus distance reference mark
29 Hot shoe
30 Mode dial
31 Status indicator
32 [Q.MENU] button
33 [FILM MODE] button
34 [MIC/REMOTE] socket
35 Shoulder strap eyelet
sBe sure to attach the shoulder strap when
using the camera to ensure that you will not
drop it.
36 [HDMI] socket
37 [AV OUT/DIGITAL] socket
38 Card door
39 DC cable cover
28 29
2423 25
26
27
33323130
36
35
34
37
39
38
40 Battery door
41 Release lever
42 Tripod receptacle
sWhen you use a tripod, make sure the tripod
is stable when the camera is attached to it.
Lens
H-VS014140 (LUMIX G VARIO HD 14 –140 mm/F4.0–5.8 ASPH./MEGA O.I.S.)
43 Tele
44 Lens surface
45 Focus ring
46 Wide
47 Zoom ring
48 [O.I.S.] switch
49 Contact point
50 Lens fitting mark
Battery charger/AC adaptor
51 Power input socket [AC IN]
52 [CHARGE] indicator
53 Power output socket [DC OUT]
54 Battery holder
424140
45 46 49 50
48
47
43 44
5352
51
54

18
Mode switching
Basic
Selecting the [REC] mode, and record still picture
or motion picture
Turn the camera on.
sThe status indicator lights when you turn this unit
on .
sMake sure the drive mode lever is set to [ ].
Switching the mode by rotating the mode
dial.
Align a desired mode with part .
sRotate the mode dial slowly and surely to adjust
to each mode. (
The mode dial rotates 360 Q )
Basic
Intelligent Auto Mode
The subjects are recorded using settings automatically selected by the camera.
Program AE Mode
The subjects are recorded using your own settings.
ON
OFF
Advanced
Advanced Scene Mode
Aperture-priority AE Mode
The shutter speed is automatically determined by the aperture value you set.
Shutter-priority AE Mode
The aperture value is automatically determined by the shutter speed you set.
Manual Exposure Mode
The exposure is adjusted by the aperture value and the shutter speed which are
manually adjusted.
Creative Motion Picture Mode
Record motion picture with manual settings.
Custom Mode
Use this mode to take pictures with previously registered settings.
Scene Mode
This allows you to take pictures that match the scene being recorded.
My Color Mode
Easily check the color of light, brightness, and vividness of color when the picture is
taken.
Portrait mode
Use this mode to take pictures of people.
Scenery mode
Use this mode to take pictures of scenery.
Sports mode
Use this mode to take pictures of sporting events, etc.
Close-up mode
Use this mode to take pictures of a close-by subject.
Night portrait mode
Use this mode to take pictures of night scenes and people against night time scenery.

19
About the Lens
This unit can use the dedicated lenses compatible with the Micro Four Thirds ™ System
lens mount specification (Micro Four Thirds mount) such as the LUMIX G VARIO HD
14–140 mm/F4.0–5.8 ASPH./MEGA O.I.S. lens included in DMC-GH1K.
Select a lens that matches the scene being recorded and your use of the pictures.
If you use a lens other than a dedicated interchangeable lens, auto focus cannot be
activated and accurate metering is not possible. Also, some functions will not work.
“Micro Four Thirds Mount”
This is the lens mount standard for the
“Micro Four Thirds System”.
This was newly developed as
interchangeable lens dedicated for digital
cameras.
When using lenses other than the 14 –140 mm/F4.0– 5.8 lens included in
DMC-GH1K
sDepending on the type of lens, you may not be able to use some functions such as the direction
detection function, [STABILIZER], Quick AF and Continuous AF.
sThe available flash range etc. differs depending on the aperture value of the lens you are using.
sTa k e s o me t e s t p ic t u re s w it h t h e l e n s y o u a r e u s in g .
sLens with the Four Thirds™ mount
specification can be used by using the mount
adaptor (DMW-MA1; optional). Because of its
structure, Micro Four Thirds mount
specification lenses cannot be used on the
Four Thirds mount specification cameras. It
can only be used on the Micro Four Thirds
mount specification cameras.
Interchangeable lens that can be used with this unit and compatibility of the functions
(: Usable, :Somefunctions/featureslimited,—:Notusable)
1 Mount adaptor (DMW-MA1; optional) is necessary to use with this unit.
2Whenrecordingmotionpictures,thefocusiscontinuouslyadjustedforboth[AFS]and[AFC]
3FewertrackingfunctionsarecompatiblethanwiththeMicroFourThirdsmountspecification
lens compatible with motion pictures. Also, the sound of auto focus operation may be
recorded.
4Autofocusdoesnotworkand[MF]isusedwhenrecordingwith[RECMODE]setto
[AVCHD] and [REC QUALITY] set to [FHD] ([ ]).
5Thesoundofapertureoperationmayberecorded.
Lens type
when recording still pictures while recording motion pictures
Auto focus Auto aperture
setting Auto focus Auto aperture setting
Micro Four Thirds
mount specification
lens compatible to
motion pictures
(LUMIX G VARIO
HD)
([AFS], [AFC])
2
Micro Four Thirds
mount specification
lens not compatible
to motion pictures
([AFS], [AFC])
2, 3, 4 5
Four Thirds mount
specification lens
compatible to
contrast AF
1
([AFS])
3, 4 5
Four Thirds mount
specification lens
not compatible to
contrast AF
1
— — 5
Refer to catalogues/Web pages for most current information regarding compatible lenses.
http://panasonic.co.jp/pavc/global/cs (This Site is English only.)

20
Cautions for Use
Take care not to drop or knock the unit or put a lot of pressure on it.
sTa k e c a r e n o t t o k n o c k or d r o p t h e b a g / c a s e t h a t y o u i n s e r t e d t h e c a m e r a i n a s t h e s h oc k m a y
cause damage to the camera, lens or LCD monitor.
sDo not use a paper bag as it can easily rip causing the camera to fall and be damaged.
sWe strongly recommend you purchase a good camera bag/case from your local dealer to
protect your camera.
Keep the camera as far away as possible from electromagnetic equipment (such as
microwave ovens, TVs, video games etc.).
sIf you use the camera on top of or near a TV, the pictures and sound on the camera may be
disrupted by electromagnetic wave radiation.
sDo not use the camera near cell phones because doing so may result in noise adversely
affecting the pictures and sound.
sRecorded data may be damaged, or pictures may be distorted, by strong magnetic fields
created by speakers or large motors.
sElectromagnetic wave radiation generated by microprocessors may adversely affect the
camera, disturbing the pictures and sound.
sIf the camera is adversely affected by electromagnetic equipment and stops functioning
properly, turn the camera off and remove the battery or disconnect AC adaptor. Then reinsert
the battery or reconnect AC adaptor and turn the camera on.
Do not use the camera near radio transmitters or high-voltage lines.
sIf you record near radio transmitters or high-voltage lines, the recorded pictures and sound may
be adverselyaffected.
Always use the supplied cords and cables. If you use optional accessories, use the
cords and the cables supplied with them.
Do not extend the cords or the cables.
Do not spray the camera with insecticides or volatile chemicals.
sIf the camera is sprayed with such chemicals, the body of the camera may be damaged and the
surface finish may peel off.
sDo not keep rubber or plastic products in contact with the camera for a long period of time.
Before cleaning the camera, remove the battery or disconnect the power plug from
the outlet. Then wipe the camera with a dry soft cloth.
sWhen the camera is soiled badly, it can be cleaned by wiping the dirt off with a wrung wet cloth,
and then with a dry cloth.
sWipe off any dirt or dust on the zoom ring and the focus ring with a dry, dustless cloth.
sDo not use solvents such as benzine, thinner, alcohol, kitchen detergents, etc., to clean the
camera, since it may deteriorate the external case or the coatingmaypeeloff.
sWhen using a chemical cloth, be sure to follow the accompanying instructions.
Optimal use of the camera
Cleaning