Panasonic WhisperCeiling FV-20VQ3 User manual

1
INSTALLATION
INSTRUCTIONS
Ventilating Fan FV-20VQ3 FV-30VQ3 FV-40VQ3
Panasonic
READ AND SAVE THESE INSTRUCTIONS.
Please read these instructions carefully before attempting to install,
operate or service the Panasonic Ventilating Fan. Failure to comply
with instructions could result in personal injury and/or property
damage. Please retain this booklet for future reference.
Table f C ntents
upplied Accessories.......................................................................................... 2
Description .......................................................................................................... 2
Dimensions ......................................................................................................... 3
pecifications ...................................................................................................... 3
Unpacking ........................................................................................................... 3
General afety Information ................................................................................. 4
Installation I ( uspended Ceiling)....................................................................... 5
Installation II (Wooden Header Installation) ....................................................... 6
Installation III (In Existing Construction)............................................................. 7
Maintenance........................................................................................................ 7–8
Product ervice .................................................................................................. 8
Panasonic_E 19/02/02, 11:24 AMPage 1 Adobe PageMaker 6.5C/PPC

2
SUPPLIED ACCESSORIES
FV-20VQ3 FV-30VQ3 FV-40VQ3
Part name Appearance Quantity
Grille 1
uspension
bracket set
uspension 4
bracket
Rubber 1 4
Rubber 2 4
Rubber 3 4
Washer 8
crew 8
Long screw 6
DESCRIPTION
These Panasonic ceiling mount ventilating fan models use a low noise sirocco fan driven by a capacitor motor.
The motor is designed to have an extended service life with reduced energy consumption.
It also incorporates a thermal-cutoff for safety. The grille covering the main body is a spring-loaded, quick-remove type.
A damper for preventing counterflow is provided.
Panasonic_E 19/02/02, 11:24 AMPage 2 Adobe PageMaker 6.5C/PPC

3
Model no. Air direction V Hz Power consumption peed Air deliver at Weight
(W) (RPM) 0.1" WG (CFM) kg (lb.)
FV-20VQ3 43.5 560 200 6.2 (13.6)
FV-30VQ3 Exhaust 120 60 66.5 730 300 6.7 (14.7)
FV-40VQ3 119 680 400 9.6 (21.1)
*At 0.0" tatic pressure, (Pa)
DIMENSIONS
FV-20VQ3 FV-30VQ3 FV-40VQ3
No. Part name No. Part name
1Grille 5Body
2Adapter 6Damper
3Junction box 7Plug connector
4Junction box cover 8uspension bracket
Dimensions: mm (inch)
M del N . ABCDEF G H I
FV-20VQ3 420 312 142 146 236 22 380ⵧ309ⵧ357ⵧ
FV-30VQ3 (16 17/32) (12 9/32) (5 19/32) (5 3/4) (9 9/32) (7/8) (15ⵧ) (12 3/16ⵧ) (14 1/16ⵧ)
FV-40VQ3 484 376 142 146 236 22 450ⵧ374ⵧ422ⵧ
(19 9/16) (14 25/32) (5 19/32) (5 3/4) (9 9/32) (7/8) (17 11/16ⵧ) (14 23/32ⵧ) (16 5/8ⵧ)
M del N . J K L M N O P Q
FV-20VQ3 66 97 50 236 138 228 175–225 338–382
FV-30VQ3 (2 19/32) (3 13/16) (1 31/32) (9 5/16) (5 7/16) (8) (6 7/8–8 7/8) (13 5/16–15 1/32)
FV-40VQ3 66 161 50 250 138 292 235–285 403–447
(2 19/32) (6 11/32) (1 31/32) (9 27/32) (5 7/16) (11 1/2)
(9 5/16–11 7/32) (15 7/8–17 19/32)
SPECIFICATIONS
UNPACKING
Unpack and carefully remove unit from carton.
Refer to the supplied accessories list to verify that all parts are present.
2
3
5
4
7
6
8
1
A
B
P
H
I
JE
M
L
F
N
Q
O
K
C
D
G
Panasonic_E 19/02/02, 11:24 AMPage 3 Adobe PageMaker 6.5C/PPC

4
GENERAL SAFETY INFORMATION
1. Do not install this ventilating fan where air temperature may exceed 40°C. (104°F)
2. Make certain that the electric service supply voltage is 120V 60 Hz.
3. Follow all local electrical and safety codes, as well as the National Electrical Code (NEC) and the
Occupation afety and Health Act (O HA).
4. Always disconnect the power source before working on or near the fan, motor or junction box.
5. Protect the power cord from sharp edges, oil, grease, hot surfaces, chemicals, or other objects.
6. Do not kink the power cord.
7. Do not install the unit where ducts are configured as shown in Fig. A.
8. Provide suction parts with proper ventilation.
9. This unit is approved for use over a bathtub or shower when installed in a GFCI protected branch
circuit.
CAUTION
1. For general ventilating use only. Do not use to exhaust
hazardous or explosive materials and vapors.
2. Not for use in cooking area. (Fig. B)
3. This product must be properly grounded.
Fig. A
(Cooking area)
Do not install above
or inside this area.
Cooking
equipment Floor
WARNING:
To reduce the risk of fire, electric shock, or injury to persons, observe the following:
A. Use this unit only in the manner intended by the manufacturer. If you have any questions, contact the
manufacturer.
B. Installation work and electrical wiring must be done by qualified person(s) in accordance with all applicable
codes and standards, including fire-rated construction.
C. ufficient air is needed for proper combustion and exhausting of gases through the flue (chimney) of fuel
burning equipment to prevent backdrafting. Follow the heating equipment manufacturer’s guideline and safety
standards such as those published by the National Fire Protection Association (NFPA), and the American
ociety for Heating Refrigeration and Air Conditioning Engineers (A HRAE), and the local code authorities.
D. When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.
E. Ducted fans must always be vented to the outdoors.
F. If this unit is to be installed over a tub or shower, it must be marked as appropriate for the application.
G. Do not use this unit with any solid-state control device.
H. Before servicing or cleaning unit, switch power off at service panel and lock the “service disconnecting mains”
to prevent power from being switched on accidentally. When the service disconnecting mains cannot be
locked, securely fasten a prominent warning device, such as a tag, to the service panel.
I. NEVER place a switch where it can be reached from a tub or shower.
J. Not to be installed in a ceiling thermally insulated to a value greater than R40.
Fig. B
Panasonic_E 19/02/02, 11:24 AMPage 4 Adobe PageMaker 6.5C/PPC

5
INSTALLATION I (SUSPENDED CEILING)
1. Disconnect plug connector from receptacle before start-
ing installation.
2. Assemble suspension bracket and rubber 1 to body.
(Fig. 1)
3. uspend body with anchor bolts. (not supplied) (Fig. 2)
4. Remove junction box cover and secure conduit to junc-
tion box knockout hole. (7/8 inch) (Fig. 3)
5. Refer to wiring diagram
Using wire nuts, connect house power wires to ventilat-
ing fan wires (Fig. 3): black to black; white to white;
green to greens.
Replace junction box cover.
CAUTION
Mount junction box cover carefully so that lead
wires are not pinched.
Wiring Diagram
6. Install circular duct (6 inch) and secure it with tape.
7. Finish ceiling work. Ceiling hole should be aligned with
fan opening.
8. Connect plug connector to receptacle.
9. Insert mounting springs into slots as shown and mount
grille to fan body. (Fig. 4)
Fig. 1
Fig. 2
Fig. 3
Fig. 4
uspension bracket
crew
Rubber 1
Rubber 1
Anchor bolt
Body
Anchor bolt (Not supplied)
Rubber
2 and 3
Washer
Anchor
bolt
Green wires
Junction box Conduit
Wire nut
Lead wires
Grille
lot Mounting spring
Motor
White
Thermal Cut Off
Power upply
AC120V 60Hz
Earth
WhiteWhite
Neutral
Red
Black BlackBlack
GreenGreen
Capacitor
Live
Panasonic_E 19/02/02, 11:25 AMPage 5 Adobe PageMaker 6.5C/PPC

6
INSTALLATION II (WOODEN HEADER)
1. Install header between ceiling joists using nails or
screws. (Fig. 5)
2. Install the ventilating fan to the header with long screws.
(Figs. 5 & 6)
Fig. 5
Fig. 6
Fig. 7
Ceiling joist Header
Adapter
Ceiling joist
Ventilating fan
mm (inch)
Model No. A B
FV-20VQ3 315 454
FV-30VQ3 (12 13/32) (17 7/8)
FV-40VQ3 380 518
(15) (20 13/32)
3. Insert the circular duct to the adapter.
Remove the junction box cover and secure conduit to
junction box knockout hole. (7/8 inch) (Fig. 6)
4. Refer to wiring diagram.
Using wire nuts, connect house power wires to ventilat-
ing fan wires: black to black; white to white; green to
green. Replace junction box cover.
CAUTION
Mount junction box cover carefully so that lead
wires are not pinched.
Wiring Diagram
Long screw
Adapter
Circular duct
Junction box cover
Flange
Ceiling
5. Finish ceiling work. Ceiling hole should be aligned with
the edge of the flange. (Fig. 7)
6. Mount grille to fan body. (Fig. 4 of page 5).
Motor
White
Thermal Cut Off
Power upply
AC120V 60Hz
Earth
WhiteWhite
Neutral
Red
Black BlackBlack
GreenGreen
Capacitor
Live
Panasonic_E 19/02/02, 11:25 AMPage 6 Adobe PageMaker 6.5C/PPC

7
INSTALLATION III (IN EXISTING CONSTRUCTION)
Installing the ventilating fan in an existing building requires an accessible area (attic or crawl space) above the planned
installation location, or existing ducting and wiring.
1. To install the ventilating fan, follow the procedures described in Installation II. Take the following precautions before
installation.
CAUTION
Check area above planned installation location to be sure that:
1. Duct work can be installed and that area is sufficient for proper ventilation.
2. Wiring can be run to planned location.
3. No wiring or other obstructions will interfere with installation.
2. Inspect duct work and wiring before proceeding with installation.
3. Plan suitable location for ventilating fan (next to ceiling joist).
4. Before installation, ensure there is sufficient space available (no obstruction or interference).
MAINTENANCE
WARNING
Disconnect power source before working on unit. Routine maintenace of the fan must be done every year.
CAUTION
1. Never use petrol, benzene, thinner or any other such chemicals for cleaning the ventilating fan.
2. Do not allow water to enter motor.
3. Do not immerse resin parts in water over 60°C (140°F).
1. Remove grille. ( queeze mounting spring and pull
down.) (Fig. 8) 2. Wash and clean grille. (Use non-abrasive kitchen detergent.) Wipe dry with new cloth. (Fig. 9)
Fig. 9Fig. 8
lot
Mounting spring
Glove Grille
Panasonic_E 19/02/02, 11:25 AMPage 7 Adobe PageMaker 6.5C/PPC

8
MAINTENANCE (CONT.)
3. Remove dust and dirt from fan body using a vacuum
cleaner. (Fig. 10)
Fig. 10
Fig. 11
Cleaner
4. Using a cloth dampened with kitchen detergent, remove
any dirt from fan body. Wipe dry with new cloth. (Fig. 11)
5. Replace grille.
PRODUCT SERVICE
Warning C ncerning Rem val f C vers.
This unit should be serviced by qualified technicians only. No service information is provided for customers. Your product
is designed and manufactured to ensure a minimum of maintenance. However, should your unit ever require service, a
nationwide system of factory service centers and AUTHORIZED INDEPENDENT ERVICE CENTER are maintained to
support your product’s warranty. (In the U. .A., call 1-866-292-7292 to locate the Panasonic Authorized ervice Center
nearest you.)
PANASONIC HOME AND COMMERCIAL PRODUCTS COMPANY
One Panasonic Way, ecaucus, NJ 07094
PANASONIC CANADA INC.
5770 Ambler Drive, Missisauga, Ontario L4W 2T3
32CD54020EUL2-I0297-5
Panasonic_E 19/02/02, 11:25 AMPage 8 Adobe PageMaker 6.5C/PPC