Panasonic EH-NE42 User manual

© Panasonic Electric Works (Thailand) Co., Ltd.
2011. All rights reserved. Unauthorized copying and
distribution is a violation of law.
Order Number PEWT1103A13CE
Hair Dryer
Model No. EH-NE42
ASIA
TABLE OF CONTENTS PAGE PAGE
1 Warning-------------------------------------------------------------- 2
2 Specifications ----------------------------------------------------- 2
3 Troubleshooting Guide----------------------------------------- 3
4 Disassembly and Assembly Instructions ---------------- 4
5 Wiring Connection Diagram ---------------------------------11
6 Schematic Diagram---------------------------------------------12
7 Exploded View and Replacement Parts List -----------13

2
1Warning
Caution:
• Pb free solder has a higher melting point that standard solder; Typical the melting point is 50 - 70°F (30 - 40°C) higher. Please
use a soldering iron with temperature control and adjust it to 750 ± 20°F (400 ± 10°C). In case of using high temperature solder-
ing iron, please be careful not to heat too long.
• Pb free solder will tend to splash when heated too high (about 1100°F / 600°C).
2 Specifications

3
3 Troubleshooting Guide
Refer to WIRING CONNECTION DIAGRAM.

4
4 Disassembly and Assembly Instructions
4.1. Disassembly instruction
1. Take off nozzle as same direction in figure 4.
2. Remove 2 tapping screws by Plus Driver and 2 torx screws by IEC driver as figure 5.

5
3. Take off an air outlet grill and an air outlet ring by rotating.
Take off an air inlet ring by rotating, then pulling a rear cover as figure 6.
4. Take off a handle A from housing A and B as figure 7.

6
5. Take off a housing A from a housing B as figure 8.
6. Take off a motor heater block from a housing B as figure 9.

7
4.2. Assembly instruction
1. Install leadwire Black, Yellow, Violet, Orange, Ground lead wire and lead wire brown (from power cord) with a main switch
and a capacitor as figure 10.
2. Connecting and soldering a motor heater block with a main switch as figure 11.

8
3. Assemble discharge covers with a motor heater block.
Then assemble them with housing A and B as figure 12, 13.

9
4. Assemble motor heater block with handle B and housing B as figure 14.

10
5. Assembly handle A , screws and nozzle as shown figure 15.

11
5 Wiring Connection Diagram

12
6 Schematic Diagram

Model No. : EH-NE42 Exploded View
7 Exploded View and Replacement Parts List

Model No. : EH-NE42 Parts List
Safety
Ref.
No. Part No. Part Name & Description Q'ty Remarks
1 EHNE42T0312W TORX SCREW 3*12 2 FOR HANDLE AB *1
2 EHNE42HDHW HANDLE AB 1
3 EHNE42MSPHW MAIN SWITCH PLATE 1
4 EHNE42MSW MAIN SWITCH 1 INCLUDE 2 INSULATION TUBES (FOR 615,645
CODE)
4 EHNE42MS2W MAIN SWITCH 1 INCLUDE CAPACITOR, 4 INSULATION TUBES (F
OR 655,685 CODE)
5 EHNE42DECSW DISCHARGE ELECTRODE COVER 1
6 EHNE42HSNW HOUSING AB 1
7 EHNE42SRTW SWIVEL RING 1
8 EHNE42T2005W TAPPING SCREW 2.0*5 2 FOR HOUSING AND REAR COVER *1
9 EHNE42NZYW NOZZLE 1
10 EHNE42AOGW AIR OUTLET GRILL 1
11 EHNE42AORW AIR OUTLET RING 1
12 EHNE42MHB2W MOTOR HEATER BLOCK 1 B2-PLUG,INCLUDE 2 INSULATION TUBES
12 EHNE42MHS3W MOTOR HEATER BLOCK 1 S3-PLUG,INCLUDE 2 INSULATION TUBES
13 EHNE42AIRHW AIR INLET RING 1
14 EHNE42RCSW REAR COVER 1
15 EHNE42T3080W TAPPING SCREW 3*8 2 FOR POWER CORD RETAINER *1
16 EHNE42PCRBW POWER CORD RETAINER 1
- EHNE42S03W INSTRUCTION BOOKLET 1
- EHNE4261501W INDIVIDUAL PACKAGE 1 FOR 615 CODE (INDIA)
- EHNE4264501W INDIVIDUAL PACKAGE 1 FOR 645 CODE (VIETNAM)
- EHNE4265501W INDIVIDUAL PACKAGE 1 FOR 655 CODE (MALAYSIA)
- EHNE4268501W INDIVIDUAL PACKAGE 1 FOR 685 CODE (S'PORE,HONG KONG,KUWAIT,UA
E)