Panasonic HOME IoT User manual

PanasonicHOMEIoT
InstallationGuide
Warning
2020.7ver.1.0
・
 AHomeIoTGateway(MKG100C913)(referredto
belowasthe“Gateway”)isrequiredtousethe
PanasonicHOMEIoTApp.Ensurethatyoursmart-
phoneisconnectedtothesamehomewireless
network(WLAN)astheGateway.
・
 TheAppusesyourPanasonicID,
whichyoucanreceivebyemailfrom
sender.pcpf.panasonic.com.
・
 YoumayregisteronlyonePanasonicID.However,
thereisnolimittothenumberofsmartphones
youcanregistertoeachPanasonicID.
・Allimagesshowninthisdocumentarefor
illustrativepurposeonly.
PanasonicLifeSolutionsEurope
PanasonicElectricWorksEuropeAG
Contact: Mon.-Thu.／8：00〜12：0013：00〜17：00
[phone] Fri.／8：00〜12：0013：00〜14：00

Contents
SystemOverview P.3
InstallationFlow P.4
DownloadthePanasonicHOMEIoTApp P.6
InstallationandAppSetupbyInstaller P.7-P.30
AppSetupbyUser P.31-P.37
ErrorMessages,ImportantNotesandReferenceMaterials
P.42
ErrorMessages
NamesofComponents P.5
Other P.38-P.40
ImportantNotes
ReferenceMaterials
P.43-P.44
P.44
2

SystemOverview
Panasonic
CloudServer
HomeIoT
Gateway
PowerMeasuring
Unit

internet
WLANRouter
HOME
868MHz（Panasonic）
WLAN
Temperature/
HumiditySensor
(Indoor)
Temperature/
HumiditySensor
(Outdoor)
ThissystemlayoutisrepresentativeofasystemconfigurationasofJuly2020.
（MKG100C913）
(MKG1500-DE) (MKG1301913) (MKG1302913)
3

Theflowoftheinstallationandsetupprocessisprovidedwithpagereferences.Stepsinaboxareoptional.
STEP1 ConnectthePanasonicHOMEIoTApptotheHomeIoTGateway
DownloadthePanasonicHOMEIoTApp
STEP4
STEP5 ConnecttheHomeIoTGatewaytotheinternet
CheckthewirelesssignalstrengthtotheHomeIoTGateway
STEP2
STEP3
SetupthePowerMeasuringUnit
STEP1 CreateaPanasonicID
InitialregistrationtousetheApp
STEP2
InstallationFlow
InstallationandAppSetupbyInstaller AppSetupbyUser
Preparation
FirstOperation
*Fordetails,seethePanasonicHOMEIoTSmartphoneAppGuide.
P.33
P.31
P.28
P.26
SetuptheTemperature/HumiditySensor
P.23
P.7
P.6
P.14
option
4

NamesofComponents
StatusLED
ResetButton
TabTab
WLANAPSwich
(Swich1)
ACadapterterminal
Cordaperture
SceneControlButton
HomeIoTGateway
（MKG100C913）
PowerMeasuringUnit
（MKG1500-DE）
Temperature/HumiditySensor
(Indoor:MKG1301913,Outdoor:MKG1302913)
Rear
Front
Front
Rear
Lower
Side
Upper
Side
ApplicationLED
Cover
Front
SETbutton
CTconnector
Power
terminals LowBattery
Lamp(Red)
Supplied
LithiumBattery
Connector
RegisterLamp
(Red)
RegisterButton
RefreshButton
Incoming
DataLamp(Red)
*ImagesdepicttheMKG1301913(Indoor)model.
REGISTER-LED
5

*Screenlayoutmaydifferdependingonyoursmartphonemodel.
Screenlayoutmaychangewithoutnotice.(July2020)
*PanasonicHOMEIoTisafreedownload.
*iPhoneusersrequireanAppleIDtodownloadtheApp.
*CompatibleOSversions:
iOS:Version11orhigher
Android:Version5.0orhigher
PleasedownloadthePanasonicHOMEIoTApp.
Note
PanasonicHOMEIoT Search
Androidusersclickhere iPhoneusersclickhere
AppStore
Downloadonthe
GooglePlay
Getiton
Downloadthe
PanasonicHOMEIoTApp
Preparation
6

InstallationandAppSetupbyInstaller
TheHomeIoTGateway
(MKG100C913)
includestheproducts
totheright.
HomeIoTGateway ACadapter（C-type）
HomeIoTGateway
PanasonicHOMEIoTApp
ConnectthePanasonic
HOMEIoTAppto
theHomeIoTGateway
STEP1
7

Removethecoverusingthetabson
therearofthecover.
Removethecover.
1
ConnectthePanasonicHOMEIoTApptotheHomeIoTGateway
PlugintheACadapter,
passingthecord
throughthecordstops.
2Reattachthecover.
3
InstallerTasks
Alignthecoverandbodysothatthecord
passesthroughthecordaperture.
Note
Cover
TabTab
Cordstops(x3)
Powerplug
ACadapter
terminal
Rear
Cordaperture
STEP1
8

CheckthattheStatusLEDontherearofthe
Gatewaydoubleflashesingreen.Itwilltake
around1minutetostartupafterpluggingtheAC
adapterintothewallsocket.
PlugtheACadapterintothewallsocket.
4
ConnectthePanasonicHOMEIoTApptotheHomeIoTGateway
InstallerTasks
Oncethestart
screenappears,
tapthe“Start”
button.
TaptoopenthedownloadedPanasonicHOMEIoTApp
onyoursmartphone.
5
Rear
StatusLED
STEP1
9

ConnectthePanasonicHOMEIoTApptotheHomeIoTGateway
InstallerTasks
Theinstallprocedureisdisplayed.
Checkthedetailsandtapthe
“Start”button.
*Installationfollowsthe
followingprocess.
❶Connectyour 
smartphonetothe
Gateway.
❷RegisterthePower
MeasuringUnitand
sensorstotheGateway.
❸ConnecttheGateway
totheinternet.
Tapthe“Installersettings”button.
6
Next,proceedaccordingtotheinstructions
inthePanasonicHOMEIoTApp.
7
STEP1
10

Tapthe
“Next”button.
Ifthereareno
problems,tap
the“Next”
button.
TheGatewaymaytakearound1minute
tobootafterpoweringon.
Note
First,maketheinitialconnection
fromthesmartphonetotheGateway.
8
Switchtheconnectionmodeto“ON”.
9
ConnectthePanasonicHOMEIoTApptotheHomeIoTGateway
InstallerTasks
CheckthattheStatusLEDontherearoftheGatewayiseitherlitor
doubleortripleflashing,andsetWLANAPswitch1totheOnposi-
tion.TheGatewaywillimmediatelyenterAPmode.OnceinAPmode,
theApplicationLEDonthefrontoftheGatewaywillflashinorange.
PreparetheGatewayand
checkthatthepowerison.
ApplicationLED
1234
ON
StatusLED
Rear
WLANAPswitch
STEP1
11

Wirelessrouter1111
HomeIoTGW-XXXXXXX
123455GHz
PP-01-23456
router-A-0001
aa-wireless
Abcd-router10
ConnectthePanasonicHOMEIoTApptotheHOMEIoTGateway
InstallerTasks
10
TheHomeIoTGatewaySSIDisdisplayedas“HomeIoTGW-XXXXXXX”.
*TheXXXXXXXsectionindicatesnumbers.
SelectandconnecttotheGatewayʼsSSID
usingtheWi-FiSettingsonyoursmartphone.
1.Tapthe“GotoWi-FiSettings”buttontoopenthe
Wi-FiSettingsonyoursmartphone.
2.SelecttheGatewayʼsSSID.
3.OncetheselectedSSIDhasachecknexttoitindicating
itisconnected,taptheBackbuttononyoursmartphoneʼs
navigationbartoreturntothePanasonicHOMEIoTApp.
1.Beforetappingthe“PushhereafterWi-FiSettings”button
ontheguidancescreen,tapyoursmartphoneʼsHomebutton
toreturntoyourhomescreen.
2.TaptheSettingsicontoopenthesettingsscreen.
3.UnderWi-FiSettings,selecttheGatewayʼsSSID.
4.OncetheselectedSSIDhasachecknexttoitindicatingitis
connected,taptheHomebuttontoreturntoyourHomescreen.
NowtaptheappiconagaintoreturntothePanasonicHOMEIoTApp.
5.Tapthe“PushhereafterWi-FiSettings”buttonontheguidancescreen.
TheconfigurationprocessdiffersforAndroidandiOSsmartphones.
Android
iOS
1.
2.
2.
3. 4.
5.
HomeIoTGW-XXXXXXX
123455GHz
Wirelessrouter1111
PP-01-23456
outer-A-0001
Abcd-router10
Push here after Wi-Fi Settings
IMPORTANT
HomeIoTGW-XXXXXXX
Wirelessrouter1111
PP-01-23456
router-A-0001
aa-wireless
Abcd-router10
123455GHz
1.
3.
HomeIoTGW-XXXXXXX
Wirelessrouter1111
PP-01-23456
router-A-0001
aa-wireless
ABCDE-0001
Abcd-router10
123455GHz
STEP1
12

Tapthe“Next”button
tomoveto
thenextstep.
Thesmartphoneissuccessfully
connectedtotheGateway.
11
ConnectthePanasonicHOMEIoTApptotheHomeIoTGateway
InstallerTasks
Gotothenextstep
Tap "Next" button to proceed tothe next step.
*If not connedted tothe Gateway properly,
an error screen will be displayed after tapping "Next" button.
STEP1
13

ThePowerMeasuringUnit(MKG1500-DE)
includesthefollowingproducts.
InstallationandAppSetupbyInstaller
PowerMeasuringUnit
（MKG1500-DE）
CT×3CTCable(2m)
（MKG1500-DE）
Ifsolargeneratingorstoragebatterysystemsaretobe
monitored,theoptionalproducttotherightisrequired.
*2setsarerequiredifbothsolargeneratingand
storagebatterysystemsaretobeconnected.
(MKG1510-DE)
CTSensor
(Option)
SetupthePower
MeasuringUnit
STEP2
14

SetupthePowerMeasuringUnit InstallerTasks
IfthePowerMeasuring
Unitistobepositioned
inaconsumerunit,
ensurethatatleast
50mmofspaceis
providedabovetheunit
an230mmbelowthe
unit.Afterdetermining
theposition,tapthe
“Next”button.
Refertothediagram
fortheinstallationof
thePowerMeasuring
Unit.Toremove,usea
flat-headscrewdriver
tolowerthetab
beforepullingout.
Afterinstallation,tap
the“Next”button.
Installationofthe
PowerMeasuring
Unitmustbecarried
outbyacompetent
person.
Ifyouareacompe-
tentperson,tapthe
“OK”buttonto
continue.
Followtheinstructionsinthe
PanasonicHOMEIoTAppto
installandregisterthePower
MeasuringUnit.
Tapthe
“PowerMeasuringUnit”
buttontostart
registration.
1Installationmustbe
carriedoutbya
competentperson.
2
Ensurethemainbreaker
isopenedbeforestarting
thetask.
Note
First,determinethe
installationpositionofthe
PowerMeasuringUnit.
3AttachthePower
MeasuringUnittoarail
withintheconsumerunit.
4
Tappingthe“Next”
buttononthefinal
screenof
bringsupthe
screentotheleft.
STEP2
STEP1
15

SetupthePowerMeasuringUnit InstallerTasks
Ifthepowerwirestraddles
theDINrail,passit
throughtherear.*Power
wiresmustbesolidcore
andsizedat2.5mm².
Note
*Donotinsertapowerwireintothescrewdriveraperture.
*Useaflat-headscrewdriverwithtipwidth2.0to3.5mm.
*Afterconnectingthepowerwire,checkitcannotberemovedbylightlytugging.
*Donotuseabent,damagedorotherwisedeformedpowerwire.
*Adamagedpowerwirecanbetrimmed.
*Inappropriatewiringmaycausepoorretention,poorconnectionoroverheating.
Note
IMPORTANT
Connectionmethodfor
asinglephase,2-wiresystem.
5
ConnectionmethodforpowerandCT.
6
ConnectionmethodforpowerandCT.
7
Forasinglephase,
2-wiresystem,connect
thewirestoterminals
V1-VNonthePower
MeasuringUnit.
UseonlyI1ontheCT
anddonotconnect
theotherCT.
1.Preparethepower
wireandformthe
wirealongapath
fromthededicated
circuitbreakertothe
PowerMeasuring
Unit.
2.Preparethededicatedcircuitbreakerendofthepowerwireandconnect
ittothededicatedcircuitbreaker.
3.Remove10mmofinsulationfromthePowerMeasuringUnitsideofthe
powerwiretomatchtheunit'sstripgauge.(Powerwiresmustbesolid
coreandsizedat2.5mm²)
4.Connectpowerwirestothepowerconnectionterminals,asperthe
numberofvoltagephasesstatedonthePowerMeasuringUnit.Power
wireconnectionmethod:Pushthepowerwiretothebackofthepower
terminalwireaperturewhileaflat-headscrewdriverisinsertedintothe
screwdriveraperture.Oncethepowerwireisfullyinserted,removethe
screwdrivertolockthepowerwireinposition.
UnusedCTsmaybeused
forsolargenerationor
storagebatterysystemson
asinglephase,2-wire
systembypurchasingaCT
Cable(MKG1530-DE),
availableseparately.
Onceconnect,
tapthe“Next”button.
Tapthe
“Next”button.
Tapthe“Next”button.
Prepareadedicatedbreakerto
ensurethepowerMeasuring
Unitispowered.
STEP2
16

Note
SetupthePowerMeasuringUnit InstallerTasks
ConnectionmethodforpowerandCT.
8
Connectionmethod
forpowerandCT.
9
Connectionmethodforpower
andCTwithsolargeneration
andstoragebatterysystem.
10
5.PasstheCTCablethroughfromthePowerMeasuringUnituntil
sufficientspaceisavailableforinstallationofthemainbreakerCT.
6.ConnecttheCTtothethree-waysplitsideoftheCTCable.
7.ClamptheCTonthepowerwireasperthenumberofcurrentphases
statedontheCTCable.
8.ConnectthePower
MeasuringUnitside
oftheCTCableto
 theCTconnector
labelledMAINon
thePowerMeasur-
ingUnit.
Donotremove
anyothercovers.
OncetheCTcableis
connected,tapping
the“Next”button
displaysascreenwith
anoptionforwhether
asolargenerationor
storagebattery
systemispresent.
Skipto11forYes,
or12forNo.
*EnsurethatthereisnobranchwirebetweentheCTmeasurementpointand
thepowermeter,otherwiseaccurateenergymeasurementwillnotbepossible.
*TheCTcannotprovideaccuratemeasurementsifthecurrentphaseinstallation
positionsdiffer.
*TheCThasapolarity.WhenclampingtheCTtothepowerwire,ensureyou
followthedirectionlabelontheCT.
*DonotusetheCTinalocationwithwiringtemperaturesover50°C.
Note
Tapthe“Next”button.
STEP2
17

SetupthePowerMeasuringUnit InstallerTasks
ACTCableset(MKG1510-DE),availableseparately,
isrequiredforconnection.
ConnectionmethodforpowerandCTwithsolar
generationandstoragebatterysystems.
11
Checkingtheconnectionofthe
PowerMeasuringUnittotheGateway.
12
(1)RemovethecoverandpasstheCTCableandconnectittotheCTconnectoronthe
PowerMeasuringUnitlabelled“PV”formeasurementofasolargenerationsystem
ortheconnectorlabelled“SB”formeasurementofastoragebatterysystem.
(2)Checkthephaseofthebreakerconnectedtothesolargenerationorstorage
batterysystembeingmeasured,andconnectandinstalltheCTtoI1,I2andI3on
theCTCablesothattheyconnecttoV1,V2andV3onthepowerwire.
1.Arethephasesonthepowerterminalconnectionwirescorrect?
2.Arepowerterminalwiresonthecorrectpositionandfullyinserted?
3.IstheCTinstallationpositionanddirectioncorrect?
4.IstheCTCableinstalledinthecorrectlocation?
5.Turnthededicatedpowerconnectionbreakerandmainbreakeron,
andcheckthePowerMeasuringUnitpowerLEDlightsup.
Oncechecksarecomplete,tapthe"Next"button.
Note *ToattachmultiplesolarPVorstoragebatterysystems,thepositionoftheclamp
shouldbewherethesystemsshareawire.Ifsuchaconnectionsiteisnot
available,onlyasinglesystemcanbemeasured.Additionally,measurementwill
notbepossibleiftheratingisexceeded(63A).
*Whenaddingacableforasolargenerationorstoragebatterysystemtoan
existingsystem,ensurethatthemainbreakerordedicatedpowerconnection
breakeris“OFF”priortocommencingwork.
Onceconnect,
tapthe“Next”button.
IMPORTANT
STEP2
18

Tapthe
“Next”button.
Ifthereare
noproblems,
tapthe
“Next”button.
Ittakesaround1minutefortheGatewayto
bootafterpoweringon.
Note
ConnectthesmartphonetotheGateway.
13
SwitchtheGatewayʼsWLANAPswitch
totheONposition.
14
SetupthePowerMeasuringUnit InstallerTasks
ChecktheStatusLEDontherearoftheGatewayiseitherlitorrepeats
adoubleortripleflash,andsetWLANAPswitch1totheOFFposition,
andthebacktotheONposition.TheGatewaywillimmediatelyenter
APmode.OnceinAPmode,theApplicationLEDonthefrontofthe
Gatewaywillflashinorange.
ApplicationLED
1234
ON
StatusLED
Rear
WLANAPswitch
STEP2
19

15
SetupthePowerMeasuringUnit InstallerTasks
Wirelessrouter1111
HomeIoTGW-XXXXXXX
123455GHz
PP-01-23456
router-A-0001
aa-wireless
Abcd-router10
TheHomeIoTGatewaySSIDisdisplayedas“HomeIoTGW-XXXXXXX”.
*TheXXXXXXXsectionindicatesnumbers.
SelectandconnecttotheGatewayʼsSSID
usingtheWi-FiSettingsonyoursmartphone.
1.Tapthe“GotoWi-FiSettings”buttontoopenthe
Wi-FiSettingsonyoursmartphone.
2.SelecttheGatewayʼsSSID.
3.OncetheselectedSSIDhasachecknexttoitindicating
itisconnected,taptheBackbuttononyoursmartphoneʼs
navigationbartoreturntothePanasonicHOMEIoTApp.
1.Beforetappingthe“PushhereafterWi-FiSettings”button
ontheguidancescreen,tapyoursmartphoneʼsHomebutton
toreturntoyourhomescreen.
2.TaptheSettingsicontoopenthesettingsscreen.
3.UnderWi-FiSettings,selecttheGatewayʼsSSID.
4.OncetheselectedSSIDhasachecknexttoitindicatingitis
connected,taptheHomebuttontoreturntoyourHomescreen.
NowtaptheappiconagaintoreturntothePanasonicHOMEIoTApp.
5.Tapthe“PushhereafterWi-FiSettings”buttonontheguidancescreen.
TheconfigurationprocessdiffersforAndroidandiOSsmartphones.
Android
iOS
1.
2. 3. 4.
5.
HomeIoTGW-XXXXXXX
123455GHz
Wirelessrouter1111
PP-01-23456
outer-A-0001
Abcd-router10
IMPORTANT
1.
2. 3.
HomeIoTGW-XXXXXXX
Wirelessrouter1111
PP-01-23456
router-A-0001
aa-wireless
ABCDE-0001
Abcd-router10
123455GHz
HomeIoTGW-XXXXXXX
Wirelessrouter1111
PP-01-23456
router-A-0001
aa-wireless
Abcd-router10
123455GHz
STEP2
20